Chamberlain ELITE SERIES K1A6426-2 Bedienungsanleitung

CONTROL BOARD REPLACEMENT KIT

K1A6426-2

Before installing the new control board, be sure to note the locations of all terminal block connections.

After installing the new control board, the limits, force adjustments and remote controls will have to be reprogrammed.

To reduce the risk of SEVERE INJURY or DEATH:

• Disconnect ALL electric and battery power BEFORE performing ANY service

or maintenance.

• Without a properly installed safety reversal system, persons (particularly small children)

could be SERIOUSLY INJURED or KILLED by a closing gate.

• Too much force on gate will interfere with proper operation of safety

reversal system.

• NEVER increase force beyond minimum amount required to close gate.

• NEVER use force adjustments to compensate for a binding or sticking gate.

• If one control (force or travel limits) is adjusted, the other control may also need

adjustment.

• After ANY adjustments are made, the safety reversal system MUST be tested. Gate MUST

reverse on contact with a rigid object.

• READ AND FOLLOW ALL INSTRUCTIONS.

• ANY maintenance to the operator or in the area near the operator MUST NOT be

performed until disconnecting the electrical power and locking-out the power via the

operator power switch. Upon completion of maintenance the area MUST be cleared and

secured, at that time the unit may be returned to service.

• Disconnect power at the fuse box BEFORE proceeding. Operator MUST be properly

grounded and connected in accordance with local electrical codes.

NOTE: The operator should be on a separate fused line of adequate capacity.

• NEVER let children operate or play with gate controls. Keep the remote control away

from children.

• ALWAYS keep people and objects away from the gate. NO ONE SHOULD CROSS THE

PATH OF THE MOVING GATE.

• Test the gate operator monthly. The gate MUST reverse on contact with a rigid object or

stop when an object activates the non-contact sensors. After adjusting the force or the

limit of travel, retest the gate operator. Failure to adjust and retest the gate operator

properly can increase the risk of INJURY or DEATH.

• Activate gate ONLY when it can be seen clearly, is properly adjusted and there

are no obstructions to gate travel.

INSTALLATION

CHGR

OVLD CTRL

AC PWR

/SOLAR

Cover

Dust Guard

Connector

Coaxial

Cable

Battery

Plug

Terminal

Blocks

Terminal

Blocks

Transformer or Solar Panel

Battery

Disconnect all electric power to the operator.

Remove the cover and dust guard from the operator.

Disconnect the battery.

Disconnect the coaxial cable and all terminal block connections

from the control board.

Remove the mounting screws from the control board.

Remove the control board.

Copy all settings from the existing control board to the new control board

(Force, Timer-To-Close, Bipart Delay, and Auto Open Jumper).

Install the new control board with the mounting screws.

Reconnect all terminal block connections and the coaxial cable.

Reconnect the battery.

Reconnect power to the operator.

Verify all other inputs and outputs as necessary (photoelectric sensors,

edges, loops, locks, alarm, reset, accessory power, open and single button).

ADJUSTMENT

Press and hold the GATE 1 left button to move the gate to the desired CLOSED position.

When the gate is in the desired position, release the button.

NOTE: The Gate 1 right and left buttons can be used to jog the gate back and forth

as needed.

When gate is in the desired CLOSED position, press the LEARN LIMITS button. The

control board will beep and the SET CLOSE LIMITS LED will stop blinking.

Close the gate.

Press and release the LEARN LIMITS button. The SET OPEN LIMIT LED will blink.

PROGRAM OPEN

Press and hold the GATE 1 right button to move the gate to the desired OPEN position.

When the gate is in the desired position, release the button.

NOTE: The Gate 1 right and left buttons can be used to jog the gate back and forth

as needed.

When the gate is in the desired OPEN position, press and release the LEARN LIMITS button.

The control board will beep and the SET CLOSE LIMITS LED will blink.

SINGLE GATE LEFT-HAND SIDE

PROGRAM CLOSE

Close the gate.

Press and release the LEARN LIMITS button. The SET OPEN LIMIT LED will blink.

PROGRAM OPEN

Press and hold the GATE 1 left button to move the gate to the desired OPEN position.

When the gate is in the desired position, release the button.

NOTE: The Gate 1 right and left buttons can be used to jog the gate back and forth

as needed.

When the gate is in the desired OPEN position, press and release and release the

LEARN LIMITS button. The control board will beep and the SET CLOSE LIMITS LED will blink.

LEARN LIMIT ASSEMBLY

The limits are internal settings that indicate when the gate is in the fully open position and the fully closed position. For proper functionality, the limits must be programmed during the

installation process. The gate has to travel a minimum of 6 feet in order to program the limits.

The programming uses a combination of buttons on the control board. The specific buttons used for programming depends on which side of the gate the primary operator is installed and how

many operators the installation includes.

BEFORE programming the limits ensure that the gate is closed and the chain is connected to the operator. To close the gate press the reset switch to RESET/DISCONNECT, then manually close the

gate. To resume normal operation press the reset switch back to NORMAL OPERATION.

SINGLE GATE RIGHT-HAND SIDE

DUAL GATES

Refer to the installation manual for dual gate programming.

Press and hold the GATE 1 right button to move the gate to the desired CLOSED

position. When the gate is in the desired position, release the button.

NOTE: The Gate 1 right and left buttons can be used to jog the gate back and forth

as needed.

When the gate is in the desired CLOSED position, press and release the

LEARN LIMITS button. The control board will beep and the SET CLOSE LIMITS LED will

stop blinking.

PROGRAM CLOSE

Programming is now complete. (If the SET OPEN LIMIT LED continues to blink, repeat

programming or refer to the following page.)

Test the limits by pressing the SINGLE BUTTON to open and close the gate.

Programming is now complete. (If the SET OPEN LIMIT LED continues to blink, repeat

programming or refer to the following page.)

Test the limits by pressing the SINGLE BUTTON to open and close the gate.

SET

DIAGNOSTIC

GATE 1

SET

DIAGNOSTIC

GATE 1

GATE 1 Left Button

GATE 1 Right Button

GATE 2

SET

LIMIT

LEARN

LIMITS

GATE 1

SET

LIMI

LEAR

LIMITS

SET

OPEN

LIMIT

"BEEP"

GATE 2

SET

LIMIT

LEARN

LIMITS

GATE 1

SET

LIMI

LEAR

LIMITS

SET

OPEN

LIMIT

"BEEP"

LEARN LIMITS Button

Outside

Property

Inside

Property

GATE 2

SET

LIMIT

GATE 1

SET

LIMI

SET

OPEN

LIMIT

LEARN

LIMITS

LEARN LIMITS Button

GATE 2

SET

LIMIT

LEARN

LIMITS

GATE 1

SET

LIMI

LEAR

LIMITS

SET

OPEN

LIMIT

"BEEP"

GATE 2

SET

LIMIT

LEARN

LIMITS

GATE 1

SET

LIMI

LEAR

LIMITS

SET

OPEN

LIMIT

"BEEP"

LEARN LIMITS Button

SET

DIAGNOSTIC

GATE 1

GATE 1 Right Button

SET

DIAGNOSTIC

GATE 1

GATE 1 Left Button

Outside

Property

Inside

Property

GATE 2

SET

LIMIT

GATE 1

SET

LIMI

SET

OPEN

LIMIT

LEARN

LIMITS

LEARN LIMITS Button

Outside

Property

Inside

Property

FORCE ADJUSTMENT

The operator is equipped with an obstruction sensing feature. If the gate encounters an

obstruction the operator will automatically reverse direction for a short time and stop. Based

on the length and weight of the gate it may be necessary to make force adjustments. The

force adjustment should be high enough that small objects such as branches or wind will not

cause nuisance interruptions but low enough to prevent serious injury to a person or a vehicle.

Use the SINGLE BUTTON to open and close the gate.

If the gate stops or reverses before reaching the fully open or closed position increase the

force by turning the force control clockwise.

If the gate hits a rigid object and does not stop or reverse, decrease the force by turning the

force control counterclockwise.

Run operator through a complete cycle and verify proper operation.

NOTE: Weather conditions can affect the gate movement, so seasonal adjustment may be

required. The force control is factory set to the mid-position.

Disconnect the operator by pressing the reset switch to RESET/DISCONNECT.

Manually close the gate.

Remove the learn limit cover and move the learn limit nut to the center position.

Press the reset switch to NORMAL OPERATION.

Program the limits again.

IF THE LIMITS WILL NOT PROGRAM

Outsid

Property

Inside

Property

TEST

After any adjustments are made, test the operator:

Use the SINGLE BUTTON to open and close the gate.

Test the limits by making sure the gate is stopping at the OPEN and CLOSE limits.

Test the force by making sure the gate will stop and reverse direction for a short time on

contact with an obstruction.

SINGLE BUTTON

RESET/

DISCONNECT

NORMAL

OPERATION

Learn Limit Nut

Learn Limit Switch

FORCE

OFF MAX

SINGLE BUTTON

LEARN

XMITTER

LEARN

XMITTER

Press and release the LEARN XMITTER button (LED will light).

Press the remote control button. The LED will flash and the alarm output will activate twice.

To program additional remote controls, repeat the steps until all the remote controls are

programmed.

TO ADD, REPROGRAM OR CHANGE A WIRELESS KEYLESS

ENTRY PIN (NOT PROVIDED)

Press and release the LEARN XMITTER button (LED will light).

Enter a 4-digit personal identification number (PIN) of your choice on the keypad.

Press the ENTER button on the keypad. The LED will flash and the alarm output will

activate twice.

TO ADD OR REPROGRAM A REMOTE CONTROL

(NOT PROVIDED)

LEARN

XMITTER

PIN Number

? ? ? ?

A combined total of 50 remote controls and keyless entry PINs can be programmed to

the operator.

ERASE ALL CODES

Press and hold the LEARN XMITTER button on the control board until the learn indicator light

goes out (approximately 6 seconds). All previous codes are now erased.

PROGRAMMING

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this

receiver and/or transmitter are prohibited, except for changing the code setting or replacing the

battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

Andere Chamberlain Steuereinheit Handbücher

Chamberlain

Chamberlain 041A8071-4 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional Security+ 395LM Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster CB202EV Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster CB1 Bedienungsanleitung

Chamberlain

Chamberlain 41D7742-7 Bedienungsanleitung

Chamberlain

Chamberlain liftmaster CB2 Bedienungsanleitung

Chamberlain

Chamberlain 041-0200-000 Bedienungsanleitung

Chamberlain

Chamberlain CLLA1 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional CB124 Bedienungsanleitung

Chamberlain

Chamberlain 41A7114-7 Bedienungsanleitung

Chamberlain

Chamberlain 945CB Bedienungsanleitung

Chamberlain

Chamberlain CB24 Bedienungsanleitung

Chamberlain

Chamberlain K1A6424-2 Bedienungsanleitung

Chamberlain

Chamberlain GCU Bedienungsanleitung

Chamberlain

Chamberlain 41A7928-3 Bedienungsanleitung

Chamberlain

Chamberlain CAPXLCAM Bedienungsanleitung

Chamberlain

Chamberlain 79LM Bedienungsanleitung

Chamberlain

Chamberlain MyQ 825LM Bedienungsanleitung

Chamberlain

Chamberlain MyQ 888LM Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster GOC1A Bedienungsanleitung

Chamberlain

Chamberlain 041D8071-4 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung