Chamberlain 1A4324 Bedienungsanleitung

1. Review the illustrations shown (Figure 1) and select the one

(A, B, or C) that matches your application.

NOTE: Illustrations shown are for LEFT hand mounting.

RIGHT hand mounting opposite.

FIGURE 1

Front of Hood

ABOVE Door Shaft

Bracket

Headplate

Door

Shaft

Front of Hood

BELOW Door Shaft

BBracket

Headplate

Door

Shaft

Top of Hood

Door

Shaft

Bracket

Headplate

2. Attach the gusset to the bracket using the four 3/8" x 1" cap

screws and hardware shown. Then tighten.

NOTE: For Application 1A attach gusset to end of bracket

marked A, etc., (Figure 2).

3. Install the four 3/8" x 1-1/2" cap screws and hardware shown.

Do not tighten.

4. Temporarily locate and clamp bracket in correct position

on headplate.

NOTE: Leave a minimum of 1" between bracket and headplate

(Figure 3).

5. Place drive sprocket on operator output shaft and driven

sprocket on door shaft. Do not insert keys or tighten set

screws.

6. Hold operator in position on bracket and wrap #50 roller

chain around drive sprocket and driven sprocket to determine

length of chain required.

NOTE: Lockwasher and nut will need to be removed and

replaced on operator mounting screws to perform this step.

NOTE: Observe location of mounting screws in slots of

bracket. Leave room in slots for chain tensioning. For

Application 1A, screws should be close to bottom of slot with

chain installed, for Application 1B, screws should be close to

top of slot, and for Application 1C, screws should be close to

end of slot towards wall. Readjust bracket if necessary and

repeat procedure before cutting chain.

NOTE: Make certain that operator shaft is above, below or in

front of door shaft, never in-line. 7. Remove operator from

bracket and cut #50 chain to required length.

3/8" Flat

Washer

3/8" Split Washer

3/8" Hex Nut

3/8 x 1"

Cap Screw

Bracket

3/8" Flat Washer

3/8" Hex Nut

3/8 x 1-1/2"

Cap Screw

3/8" Split

Washer

Gusset

FIGURE 2

Model 1A4324

GJ Hood Mount

Installation

FIGURE 3

Headplate

Top View

1" MinimumBracket

Door

Shaft

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other

reproductive harm. For more information go to www.P65Warnings.ca.gov

8. Permanently attach bracket to headplate in the location

determined in Step 6. Welding is recommended for this

procedure.

9. Attach operator to bracket using 3/8 x 1-1/2 mounting

screws and hardware. Do not tighten.

10. Insert key in driven sprocket and align driven sprocket with

drive sprocket. Tighten set screws. Do not place key in

drive sprocket at this time.

11. Wrap #50 chain around drive and driven sprocket and

connect ends using #50 master link.

12. Remove slack from chain by moving operator and mounting

screws in bracket slots. Tighten mounting screws.

NOTE: Keyway in operator output shaft may not be aligned

with keyway in drive sprocket. Complete electrical

connections to operator (refer to manual) then operate unit

with 3 button control until keyways align. Insert key in drive

sprocket and tighten set screws. Complete the installation

according to the owner’s manual.

114A1545C

Inhaltsverzeichnis

Andere Chamberlain Garagentoröffner Handbücher

Chamberlain

Chamberlain Whisper Drive Security+ HD700DS Bedienungsanleitung

Chamberlain

Chamberlain Power Drive 3132E FS2 Bedienungsanleitung

Chamberlain

Chamberlain AccessMaster Security+ M3100M-1/2HP Bedienungsanleitung

Chamberlain

Chamberlain H Bedienungsanleitung

Chamberlain

Chamberlain 8355W Bedienungsanleitung

Chamberlain

Chamberlain Power Drive Security+ PD752DS Bedienungsanleitung

Chamberlain

Chamberlain 050DCRJWF Bedienungsanleitung

Chamberlain

Chamberlain merlin professional C943 Bedienungsanleitung

Chamberlain

Chamberlain B980 Bedienungsanleitung

Chamberlain

Chamberlain 248739M Bedienungsanleitung

Chamberlain

Chamberlain GPD60 Bedienungsanleitung

Chamberlain

Chamberlain merlin MR800a Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster LM21XPBB Bedienungsanleitung

Chamberlain

Chamberlain HJ Bedienungsanleitung

Chamberlain

Chamberlain GT Bedienungsanleitung

Chamberlain

Chamberlain 8500W Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 1000A Bedienungsanleitung

Chamberlain

Chamberlain ATS 2113X 1/2 HP Bedienungsanleitung

Chamberlain

Chamberlain WhisperDrive WD962KD Bedienungsanleitung

Chamberlain

Chamberlain 8557 Bedienungsanleitung

Chamberlain

Chamberlain WHISPER DRIVE 248739 Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive Security+ WD912KS Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional Security+ 3850 Bedienungsanleitung

Chamberlain

Chamberlain 8810CB Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Craftsman

Craftsman 139.53997D Bedienungsanleitung

Bauer

Bauer CROSS18 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8124 Kurzanleitung

Craftsman

Craftsman 139.18867 Bedienungsanleitung