Chamberlain HD920EV Bedienungsanleitung

Model Number:

Serial Number:

Date of Purchase:

CONTENTS

Preparation . . . . . . . . . . . . . . . .2-5

Assembly . . . . . . . . . . . . . . . . 6-10

Installation . . . . . . . . . . . . . . 11-20

Install the Door Control. . . . . . 21-23

Install the Protector System®. . 23-26

Power. . . . . . . . . . . . . . . . . . 27-28

Adjustments . . . . . . . . . . . . . 29-31

Battery Backup. . . . . . . . . . . . 32-33

Operation . . . . . . . . . . . . . . . . . 34

Features . . . . . . . . . . . . . . . . . . 35

Door Control . . . . . . . . . . . . . 36-38

Remote Control . . . . . . . . . . . 39-40

To Erase the Memory . . . . . . . . . 40

To Open the Door Manually . . . . . 41

Maintenance . . . . . . . . . . . . . . . 42

Troubleshooting. . . . . . . . . . . 43-44

Repair Parts . . . . . . . . . . . . . 45-46

Accessories. . . . . . . . . . . . . . . . 47

Warranty. . . . . . . . . . . . . . . . . . 48

Belt Drive Battery Backup Garage Door Opener

The Chamberlain Group, Inc.

845 Larch Avenue

Elmhurst, Illinois 60126-1196

■ Please read this manual and the enclosed safety materials carefully!

■ Fasten the manual near the garage door after installation.

■The door WILL NOT CLOSE unless the Protector System®is connected and properly

aligned.

■ Periodic checks of the garage door opener are required to ensure safe operation.

■The model number label is located on the left side panel of your garage door opener.

■This garage door opener is compatible with MyQ™and Security✚2.0™ accessories.

■DO NOT enable the Timer-to-Close feature if you are installing the garage door opener

on a one-piece door. The Timer-to-Close is to be used ONLY with sectional doors.

www.chamberlain.com

Write down the following information for

future reference:

Models

HD920EV • 349544 • WD962KEV • WD962KPEV

FOR RESIDENTIAL USE ONLY

Safety Symbol and Signal

Word Review

Thisgarage door opener hasbeen designed and

tested to offer safe service provided it isinstalled,

operated,maintained and tested in strict

accordance with the instructions and warnings

contained in this manual.

When you see these Safety Symbolsand Signal

Words on the following pages, they will alert you

to the possibilityof serious injury or death if you

do notcomply with the warnings that accompany

them. The hazard maycome from something

mechanical or from electric shock. Read the

warnings carefully.

Mechanical

Electrical

When you see this Signal Word on the following

pages, it will alertyou to the possibilityof damage

to your garage door and/or the garage door

opener if you do notcomply with the cautionary

statements that accompany it. Read them

carefully.

Check the Door

1. Disable locks and remove any ropes

connected to the garage door.

2. Lift the door halfway up. Release the

door. If balanced, it should stay in

place, supported entirely by its springs.

3. Raise and lower the door to check for

binding or sticking. Ifyour door binds,

sticks, or is out of balance, call a trained

door systems technician.

4. Check the seal on the bottom of the

door.Anygap between the floor and

the bottom of the door mustnot exceed

1/4 inch (6 mm). Otherwise, the safety

reversal system may not work properly.

5. The opener should be installed above

the center of the door. If there is a

torsion spring or center bearing plate

in the way ofthe header bracket,itmay

be installed within 4 feet (1.2 m) to the

left or right of the door center.

See page 13.

Torsion Spring Extension Spring

To prevent possible SERIOUS NJURYor

DEATH:

• ALWAYS call a trained door systems

technician if garage door binds, sticks, or

isoutofbalance. An unbalanced garage

door may NOT reverse when required.

• NEVER try to loosen, move or adjust

garage door,door springs,cables,

pulleys,brackets or their hardware,

ALLof which are under

EXTREMEtension.

• Disable ALLlocks and remove ALLropes

connected to garage door BEFORE

installation and operating garage door

opener to avoid entanglement.

To prevent damage to garage door and

opener:

• ALWAYS disable locks BEFORE

installing and operating the opener.

• ONLY operate garage door opener at

120 V,60 Hzto avoid malfunction and

damage.

Preparation

üAdditional items you may need:

Survey your garage area to see if you will need

any of the following items:

q(2) 2X4 PIECES OF WOOD

Maybe used to fasten the header bracket to

the structural supports. Also used to position

the garage door opener during installation

and for testing the safetyreversing sensors.

qSUPPORT BRACKET AND FASTENING

HARDWARE

Mustbe used if you have a finished ceiling in

your garage.

qEXTENSION BRACKETS (MODEL

41A5281) OR WOOD BLOCKS

Depending upon garage construction,

extension brackets or wood blocks may be

needed to install the safetyreversing sensor.

qFASTENING HARDWARE

Alternate floor mounting of the safety

reversing sensor will require hardware not

provided.

qOUTSIDEQUICKRELEASE

(MODEL 7702CB)

Required for a garage with NO accessdoor.

qDOOR REINFORCEMENT

Required ifyou have a lightweightsteel,

aluminum, fiberglass or glass panel door.

qRAIL EXTENSION KIT

Required ifyour garage door is more than 7

feet (2.13 m) high.

Tools Needed

3/16

7/16

1/2

5/32

5/16

5/8 9/16 1/4

7/16

Preparation

Carton Inventory

Your garage door opener ispackaged in one carton which containsthe motor unitand all partsillustrated below.Accessoriesvarydepending on the garage door opener model purchased.Depending on your

model, other accessoriesmaybe included with your garage door opener.Instructions for these accessories will be attached to the accessory and are notincluded in this manual. Ifanything ismissing, carefully

check the packing material. Partsmay be stuck in the foam. Hardware for assembly and installation is shown on the nextpage. Save the carton and packing material until the installation and adjustment is

complete. The images throughout this manual are for reference only and your product may look different.

A. Header bracket

B. Pulley

C. Door bracket

D. Curved door arm

E. Straight door arm

(Packaged inside rail section)

F. Trolley

NOTE: Be sure to assemble the trolley

before sliding onto rail.

G. Emergency release rope and handle

H. Rail (1 front and 4 center sections)

I. Hanging brackets (2)

(Packaged inside rail section)

J. Garage door opener

K. Sprocket cover and screws

L. “U” bracket

M. Belt

N. Door control (Motion-Detecting Control

Panel or Smart Control Panel®)

O. Remote control

P. The Protector System®

Safety reversing sensors with 2 conductor

white and white/black wire attached:

Sending Sensor (1), Receiving Sensor (1),

and Safety Sensor Brackets (2)

NOTSHOWN

White and red/white wire

Owner's manual

Preparation

Carton Inventory

Hex Screw #8x3/8" (3)

(packed with the

sprocket cover)

Bolt

1/4"-20x1-3/4" (2)

Lock Nut 1/4"-20 (2)

Bolt

Nut 3/8" H7

Lock Washer 3/8"

Master Link

Spring

Trolley Nut

H12

Clevis Pin 5/16"x1-1/2"

H19

Ring Fastener (3)

H15

Hex Bolt 5/16"-18x7/8" (4)

H21

Lock Washer 5/16"-18 (7)

H20

Nut 5/16"-18 (8)

H16

Self-Threading Screw

1/4"-14x5/8" (2)

H14

Clevis Pin 5/16"x1"

H13

Clevis Pin 5/16"x1-1/4"

H17

Carriage Bolt 1/4"-20x1/2" (2)

H18

Wing Nut 1/4"-20 (2)

ASSEMBLY HARDWARE INSTALLATION HARDWARE

Screw 6ABx1-1/2" (2)

Drywall Anchors (2)

Screw 6-32x1" (2)

DOOR CONTROL HARDWARE

Insulated

Staples

H11

Lag Screw 5/16"-9x1-5/8" (2)

H10

Lag Screw 5/16"-18x1-7/8" (2)

Threaded

Shaft

with

Preparation

To prevent NJURY from pinching, keep hands

and fingers away from the joints while assembling

the rail.

To avoid installation difficulties, do not run the

garage door opener until instructed to do so.

1.1 Assemble the trolley by sliding the inner

trolley into the outer trolley.

1.2 Carefully remove the straight door arm

and hanging brackets packaged inside the

front rail.

1.3 Align the railson a flat surface as shown.

The front rail has a cut out window near

the end. Make sure that the larger hole on

the front rail isfacing up.

1.4 Slide the tapered end of each rail section

into the larger end of the rail section in

frontofit. The tabs along the side will lock

in place. All holes in the rail sections

should face up.

1.5 Insert a screwdriver into the hole shown

(this will temporarily keep the trolley from

sliding off the end of the rail).

1.6 Checkto make sure that the 4 plastic wear

padsare inside the inner trolley.Ifthey are

missing check all the packing material and

snap them back into place.

1.7 Slide the trolley along the rail toward the

screwdriver as shown.

Trolley

To garage

door opener

Wear Pads

Inner Trolley

Outer Trolley

Assembly

1 Assemble the rail and trolley

2 Fasten the rail to the garage door opener

To avoid SERIOUS damage to garage door

opener, use ONLY those bolts/fasteners

mounted in the top of the opener.

(Mounted in the

garage door opener)

HARDWARE

Bolt 1/4"-20x1-3/4"

Lock Nut 1/4"-20

NOTE: ONLY use the bolts removed from the

garage door opener.Place the garage door

opener on the packing material to prevent

scratching.

2.1 Insert the bolt (H2) into the hole on the

back end of the rail as shown. Tighten

securely with the locknut (H4). Do not

overtighten.

2.2 Remove the two bolts from the top of the

garage door opener.

2.3 Place the “U” bracket, flatside down onto

the garage door opener and align the

bracket hole with the bolt holes.Fasten the

“U” bracketwith the previouslyremoved

bolts.

2.4 Prop up the end of the rail on the carton to

help align it with the “U” bracket.

2.5 Slide the rail onto the “U” bracket, until it

reaches all the stops on the top and sides

of the “U” bracket.

“U” Bracket

Bolts

SLIDE RAIL TO

STOPS ON TOP AND

SIDES

Cover

Protection

Bolt Hole

Carton

Assembly

HARDWARE

Bolt H2

Bolt 1/4"-20x1-3/4"

Lock Nut 1/4"-20

Nut 3/8"

Lock Washer 3/8"

3.1 Lay the belt beside the rail, as shown.

Grasp the end with the hooked trolley

connector and pass approximately12" (30

cm) of belt through the window. Keep the

ribbed side toward the rail,and allowit to

hang.

3.2 Remove the tape from the pulley.The

center should be greased, if not, regrease

the center of the pulley.

3.3 Insert the pulley into the window of the

front rail.

3.4 Insert the bolt (H3) into the rail and pulley.

Tighten securely with the lockwasher (H7)

and nut (H6).

3.5 Rotate the pulley to be sure it spins freely.

3.6 Insert the bolt (H2) into the hole shown

and fasten with the lock nut(H4).

Screwdriver

Rail

Pulley

Trolley

Connector

Assembly

3 Install the pulley

4.1 Pull the belt around the pulley and toward

the trolley.The ribbed side mustcontact

the pulley.

4.2 Hook the trolley connector into the

retaining slot on the trolley as shown.

4.3 With the trolleyagainst the screwdriver,

dispense the remainder of the belt along

the rail length toward the motor unit and

around the sprocket. The sprocket teeth

must engage the belt.

4.4 Checkto make sure the belt isnot twisted.

Connect the trolley threaded shaft (H1)

with the master link (H5).

• Push pins of master link bar through

holes in end of beltand trolleythreaded

shaft (H1).

• Push master link cap over pins and past

pin notches.

• Slide clip-on spring over cap and onto

pin notches until both pins are securely

locked in place.

4.5 Remove the spring trolley nut (H8) from

the threaded shaft (H1).

4.6 Insert the trolley threaded shaft (H1)

through the hole in the trolley.

HARDWARE

Master Link

Spring

Trolley Nut

Threaded Shaft

with

Sprocket

Assembly

4 Install the belt

To avoid possible SERIOUS NJURY to finger from moving garage door opener:

• ALWAYS keep hand clear of sprocket while operating opener.

• Securely attach sprocket cover BEFORE operating.

Spring Trolley Nut H9 (3)

Hex Screw #8x3/8"

(Packed with the

sprocket cover)

HARDWARE

5.1 By hand, thread the spring trolley nut on the

threaded shaft(H8) until itis finger tight

againstthe trolley.Do not use any tools.

Remove the screwdriver.

(to motor unit)

5.2 Insert a flathead screwdriver tip into one

of the nut ring slotsand brace itfirmly

against the trolley.

Nut ring slot

5.3 Tighten the spring trolley nut with an adjustable wrench or a 7/16" open end wrench about a quarter turn until the spring releasesand snapsthe

nut ring againstthe trolley.This sets the spring to optimum belttension.

Nut Ring

BEFORE

(2.5 cm)

Nut Ring

AFTER

1-1/4"

(3.18 cm)

5.4 Position the sprocket cover over the garage

door opener sprocket and attach with hex

screws (H9).

Assembly

5 Tighten the belt and install the sprocket cover

Andere Handbücher für HD920EV

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chamberlain Garagentoröffner Handbücher

Chamberlain

Chamberlain 1245LMC-R 1/3 HP Bedienungsanleitung

Chamberlain

Chamberlain C870 Bedienungsanleitung

Chamberlain

Chamberlain Model MotorLift 1000 Bedienungsanleitung

Chamberlain

Chamberlain GH Handbuch

Chamberlain

Chamberlain GH Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive Security+ HD900D Bedienungsanleitung

Chamberlain

Chamberlain Dial Code Bedienungsanleitung

Chamberlain

Chamberlain ML700-GB Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional Security+ 3800 Bedienungsanleitung

Chamberlain

Chamberlain WHISPER DRIVE 248739 Bedienungsanleitung

Chamberlain

Chamberlain B980C Bedienungsanleitung

Chamberlain

Chamberlain 9601 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster LM60 Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive Security+ WD952KCS Bedienungsanleitung

Chamberlain

Chamberlain H Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster LM60 Bedienungsanleitung

Chamberlain

Chamberlain HandyLift Deluxe CR650EVO Bedienungsanleitung

Chamberlain

Chamberlain 1200 Bedienungsanleitung

Chamberlain

Chamberlain CLLP1 Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive WD922KC Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Security+ 2500B Bedienungsanleitung

Chamberlain

Chamberlain Power Drive PD600C Series Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional 387LM Bedienungsanleitung

Chamberlain

Chamberlain MyQ 8550W Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Craftsman

Craftsman 139.53997D Bedienungsanleitung

Bauer

Bauer CROSS18 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8124 Kurzanleitung

Craftsman

Craftsman 139.18867 Bedienungsanleitung