Chamberlain HD920EV Bedienungsanleitung

CONTENTS

Preparation . . . . . . . . . . . . . . . .1-4

Assembly . . . . . . . . . . . . . . . . .5-9

Installation . . . . . . . . . . . . . . 10-19

Install the Door Control. . . . . . 20-21

Install the Protector System®. . 22-25

Power. . . . . . . . . . . . . . . . . . 26-28

Adjustments . . . . . . . . . . . . . 29-31

Battery Backup. . . . . . . . . . . . 32-33

Operation . . . . . . . . . . . . . . . . . 34

Features . . . . . . . . . . . . . . . . . . 35

Door Control . . . . . . . . . . . . . 36-38

Remote Control . . . . . . . . . . . 39-40

To Erase the Memory . . . . . . . . . 40

To Open the Door Manually . . . . . 40

Maintenance . . . . . . . . . . . . . . . 41

Troubleshooting. . . . . . . . . . . 42-43

Accessories. . . . . . . . . . . . . . . . 44

Warranty. . . . . . . . . . . . . . . . . . 45

Repair Parts . . . . . . . . . . . . . 46-47

Belt Drive Battery Backup

Garage Door Opener

The Chamberlain Group, Inc.

845 Larch Avenue

Elmhurst, Illinois 60126-1196

■ Please read this manual and the enclosed safety materials carefully!

■ Fasten the manual near the garage door after installation.

■The door WILL NOT CLOSE unless the Protector System®is connected and

properly aligned.

■ Periodic checks of the garage door opener are required to ensure safe operation.

■The model number label is located on the left side panel of your garage door

opener.

■This garage door opener is compatible with MyQ®and Security✚2.0™

accessories.

■DO NOT enable the Timer-to-Close feature if you are installing the garage

door opener on a one-piece door. The Timer-to-Close is to be used ONLY with

sectional doors.

www.chamberlain.com

Model Number:

Serial Number:

Date of Purchase:

Models

• HD920EV

• HD930EV

• LW5000EV

• WD962KEV

• WD962KPEV

• WD962MLEV

• 349544

FOR RESIDENTIAL USE ONLY Write down the following information for

future reference:

Safety Symbol and Signal Word Review

This garage door opener has been designed and tested to offer safe service provided itis installed,

operated,maintained and tested in strictaccordance with the instructions and warnings contained in this

manual.

When you see these Safety Symbols and Signal Words on the following pages,they will alert you to the

possibility of serious injury or death if you do notcomply with the warnings that accompanythem. The

hazard may come from something mechanical or from electric shock.Read the warnings carefully.

Mechanical

Electrical

When you see this Signal Word on the following pages,itwill alert you to the possibility ofdamage to

your garage door and/or the garage door opener ifyou do not complywith the cautionary statements that

accompany it. Read them carefully.

Check the Door

To prevent possible SERIOUSINJURYor DEATH:

• ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance.

An unbalanced garage door may NOT reverse when required.

• NEVER try to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or their

hardware, ALLof which are under EXTREMEtension.

• Disable ALLlocksand remove ALLropes connected to garage door BEFORE installation and

operating garage door opener to avoid entanglement.

To preventdamage to garage door and opener:

• ALWAYS disable locks BEFORE installing and operating the opener.

• ONLY operate garage door opener at120 V,60 Hz to avoid malfunction and damage.

1. Disable locks and remove any ropes connected to the garage door.

2. Lift the door halfway up. Release the door. If balanced, it should stay in

place, supported entirely by its springs.

3. Raise and lower the door to checkfor binding or sticking.If your door

binds, sticks, or is out of balance, call a trained door systems

technician.

4. Check the seal on the bottom ofthe door. Any gap between the floor

and the bottomof the door must not exceed 1/4 inch (6 mm).

Otherwise, the safety reversal system may not work properly.

5. The opener should be installed above the center ofthe door. Ifthere is

a torsion spring or center bearing plate in the wayof the header

bracket, it may be installed within 4 feet (1.2 m) to the leftor rightof the

door center.See page 12.

Torsion

Spring

Extension

Spring

Preparation

Additional Items You May Need:

Surveyyour garage area to see ifyou will need any of the following items:

n(2) 2X4 PIECES OF WOOD

Maybe used to fasten the header bracket to the structural supports. Also used to position the

garage door opener during installation and for testing the safety reversing sensors.

nSUPPORT BRACKET AND FASTENING HARDWARE

Must be used if you have a finished ceiling in your garage.

nEXTENSION BRACKETS (MODEL 41A5281) OR WOOD BLOCKS

Depending upon garage construction,extension bracketsor wood blocksmaybe needed to

install the safety reversing sensor.

nFASTENING HARDWARE

Alternate floor mounting of the safety reversing sensor will require hardware not provided.

nOUTSIDEQUICKRELEASE (MODEL 7702CB)

Required for a garage with NO accessdoor.

nDOOR REINFORCEMENT

Required if you have a lightweight steel, aluminum, fiberglass or glass panel door.

nRAIL EXTENSION KIT

Required ifyour garage door is more than 7 feet (2.13 m) high.

Tools Needed

3/16

7/16

1/2

5/32

5/16

5/8

9/16

1/4

7/16

Preparation

Carton Inventory

Your garage door opener ispackaged in one carton which contains the motor unit and all parts

illustrated below.Accessories vary depending on the garage door opener model purchased. Depending

on your model, other accessoriesmaybe included with your garage door opener. Instructions for these

accessorieswill be attached to the accessoryand are not included in this manual. Ifanything is missing,

carefully check the packing material. Hardware for assembly and installation is shown on the nextpage.

Save the carton and packing material until the installation and adjustment is complete. The images

throughout this manual are for reference only and your product may look different.

A. Header bracket

B. Pulley

C. Door bracket

D. Curved door arm

E. Straight door arm

(Packaged inside front rail section)

F. Trolley

NOTE: Be sure to assemble the trolley before sliding onto rail.

G. Emergency release rope and handle

H. Rail (1 front and 4 center sections)

I. Hanging brackets (2)

(Packaged inside the front rail section)

J. Garage door opener (motor unit)

K. Sprocket cover and screws

L. “U” bracket

M. Belt

N. Door control (Motion-Detecting Control Panel or Smart Control Panel®)

O. Remote control

P. The Protector System®

Safety reversing sensors with 2 conductor white and white/black wire attached: Sending Sensor (1),

Receiving Sensor (1), and Safety Sensor Brackets (2)

NOTSHOWN

White and red/white wire

Owner's manual

Preparation

Hardware Inventory

Hex Screw

#8x3/8" (3)

(packed with the

sprocket cover)

Bolt

1/4"-20x1-3/4"

Lock Nut

1/4"-20

Bolt

Nut 3/8"

Lock Washer 3/8"

Clevis Pin 5/16"x1-1/2"

Ring Fastener (3)

Hex Bolt 5/16"-18x7/8" (4)

Lock Washer

5/16"-18 (5)

Nut

5/16"-18 (6)

Self-Threading Screw

1/4"-14x5/8" (2)

Clevis Pin 5/16"x1"

Clevis Pin 5/16"x1-1/4"

Carriage Bolt

1/4"-20x1/2" (2)

Wing Nut 1/4"-20 (2)

ASSEMBLY HARDWARE INSTALLATION HARDWARE

Screw 6ABx1" (2)

Drywall Anchors (2)

Screw 6-32x1" (2)

DOOR CONTROL HARDWARE

Insulated

Staples

(Not Shown)

Lag Screw 5/16"-9x1-5/8" (4)

Preparation

Assembly

STEP 1 Assemble the rail and trolley

To prevent INJURY from pinching, keep handsand fingersaway from the jointswhile assembling the

rail.

To avoid installation difficulties, do not run the garage door opener until instructed to do so.

The front rail has a cut out“window” at the door end (see illustration). The hole above thiswindow is

larger on the top of the rail than on the bottom.A smaller hole 3-1/2" (8.9 cm) away isclose to the rail

edge. Rotate the backrail so ithas a similar hole close to the opposite edge, about 4-3/4" (12 cm) from

the far end.

1. Remove the straight door arm and hanging bracket packaged inside the front rail and set

aside for Installation Step 5 and 9. NOTE: To prevent INJURY while unpacking the rail

carefully remove the straight door arm stored within the rail section.

2. Align the rail sections on a flatsurface as shown and slide the tapered ends into the larger

ones. Tabsalong the side will lock into place.

3. Place the motor unit on packing material to protect the cover, and restthe backend of the rail

on top. For convenience,put a support under the front end of the rail.

4. As a temporarystop, insert a screwdriver into the hole 10" (25 cm) from the front end of the rail,

as shown.

5. Check to be sure there are 4 plasticwear padsinside the inner trolley. Iftheybecame loose

during shipping, check all packing material. Snap them back into position as shown.

6. Slide the trolley assembly toward the screwdriver asshown.

7. Slide the rail onto the “U” bracket, until it reaches all the stops on the top and sides ofthe “U”

bracket.

To garage

door opener

(TO MOTOR UNIT)

Front Rail

Section

(TO DOOR)

“U” Bracket

Outer Trolley

Inner Trolley

Wear Pads

Rail

Tab

Trolley

Window

Cut-Out

SLIDE TO STOPS

ON TOP AND

SIDES OF

“U” BRACKET

Idler

Pulley

Hole

Assembly

STEP 2 Fasten the rail to the motor unit

To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fastenersmounted in the

top of the opener.

1. Insert a 1/4"-20x1-3/4" boltinto the cover protection bolthole on the backend of the rail as

shown.Tighten securely with a 1/4"-20 locknut.Do NOT overtighten.

2. Remove the two bolts from the top of the motor unit.

3. Use the carton to supportthe front end of the rail.

4. Place the “U” bracket,flat side down onto the motor unit and align the bracketholeswith the

bolt holes.

5. Fasten the “U” bracket with the previouslyremoved bolts; DO NOTuse any power tools. The

use of power toolsmay permanentlydamage the garage door opener.

(Mounted in the

Bolts

garage door opener)

HARDWARE

Bolt 1/4"-20x1-3/4"

Lock Nut 1/4"-20

“U” Bracket

Bolts

Cover Protection

Bolt Hole

Bolt 1/4"-20x1-3/4"

Lock Nut 1/4"-20

Assembly

STEP 3 Install the idler pulley

1. Lay the belt beside the rail, asshown. Grasp the end with the hooked trolley connector and

passapproximately12" (30 cm) of belt through the window. Keep the ribbed side toward the

rail,and allow it to hang until Assembly Step 4.

2. Remove the tape from the idler pulley. The inside center should be pre-greased. Ifdry,

regrease to ensure proper operation.

3. Place the idler pulley into the window asshown.

4. Insert the idler boltfrom the top through the rail and pulley. Tighten with a 3/8" lock washer and

nut underneath the rail until the lock washer is compressed.

5. Rotate the pulleyto be sure it spins freely.

6. Locate the rail tab.The rail tab is between the idler bolt and the trolley in the frontrail section.

Use a flathead screwdriver and liftthe rail tab until the tab is vertical (90º).

HARDWARE

Bolt Nut 3/8"

Lock Washer 3/8"

Screwdriver

Rail

Trolley Connector

Bolt

Lock Washer 3/8"

Nut 3/8"

Rail

Tab

CORRECT

INCORRECT

Rail Tab

Idler Pulley

Grease Inside Pulley

Assembly

STEP 4 Install the belt

1. Pull the belt around the idler pulley and toward the trolley.The ribbed side must contact the

pulley.

2. Hook the trolley connector into the retaining slot on the trolley. (a)

3. With the trolley againstthe screwdriver, dispense the remainder of the belt along the rail

toward the motor unitaround the sprocket. The sprocket teeth mustengage the belt. (b)

4. Thread the inner nut and lockwasher onto the trolleythread shaft(c). Checkto make sure the

belt is not twisted.

5. Insert the trolley threaded shaft through the hole in the trolley.Be sure the beltis not

twisted. (c)

6. Loosely thread the outer nut onto the trolley threaded shaft.

7. Remove the screwdriver.

Trolley Connector

Retaining Slot

Threaded

Shaft

Outer

Nut

Front Rail

Section

(TO DOOR)

Inner

Nut

Lock

Washer

Sprocket

Idler

Pulley

Assembly

STEP 5 Tighten the belt and install the sprocket cover

To avoid possible SERIOUS INJURY to finger from moving garage door opener:

• ALWAYS keep hand clear of sprocketwhile operating opener.

• Securely attach sprocket cover BEFORE operating.

1. Spin the inner nutand lock washer down the trolley threaded shaft, awayfrom the trolley

2. To tighten the belt, turn outer nut in the direction shown until the line on the spring retainer

plate is visible. Be sure the beltis not twisted,and the ribbed side faces the rail.

3. Tighten the inner nutto secure the adjustment.Thissets the spring to optimum belttension.

4. Position the sprocket cover over the sprocketas shown and fasten to the mounting plate with

8x3/8" hex screws provided.

You have now finished assembling your garage door opener. Please read the following warnings

before proceeding to the installation section.

Hex Screw #8x3/8"

(Packed with the

sprocket cover)

HARDWARE

Hex Screw #8x3/8"

Sprocket Cover

INCORRECT

CORRECT

Line

Lock Washer

Inner Nut

Spring RetainerOuter Nut

Line

Andere Handbücher für HD920EV

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chamberlain Garagentoröffner Handbücher

Chamberlain

Chamberlain Security+ 9902 Bedienungsanleitung

Chamberlain

Chamberlain 8164W Bedienungsanleitung

Chamberlain

Chamberlain GH Bedienungsanleitung

Chamberlain

Chamberlain 2565 1/2 HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive Security+ 8200C Bedienungsanleitung

Chamberlain

Chamberlain MyQ 819LMB Bedienungsanleitung

Chamberlain

Chamberlain MotorLift 1703EML Originalbetriebsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive Security+ WD912KS Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster LM3800A Bedienungsanleitung

Chamberlain

Chamberlain 655502 "Single" Bedienungsanleitung

Chamberlain

Chamberlain Contractor Series Bedienungsanleitung

Chamberlain

Chamberlain SLY300 Bedienungsanleitung

Chamberlain

Chamberlain 1245LMC-R 1/3 HP Bedienungsanleitung

Chamberlain

Chamberlain Power Drive PD432DM Bedienungsanleitung

Chamberlain

Chamberlain merlin MT5580P Bedienungsanleitung

Chamberlain

Chamberlain Security+ 3950 Bedienungsanleitung

Chamberlain

Chamberlain POWER DRIVE Security+ PD752D Bedienungsanleitung

Chamberlain

Chamberlain 8010 Bedienungsanleitung

Chamberlain

Chamberlain 4000UK Bedienungsanleitung

Chamberlain

Chamberlain 2265C Bedienungsanleitung

Chamberlain

Chamberlain J Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive Security+ WD962KD Bedienungsanleitung

Chamberlain

Chamberlain 3245C 1/3 HP Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Craftsman

Craftsman 139.53997D Bedienungsanleitung

Bauer

Bauer CROSS18 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8124 Kurzanleitung

Craftsman

Craftsman 139.18867 Bedienungsanleitung