Chamberlain LiftMaster Professional VSL595 Installationshandbuch

SL595 Variable Speed

Motor Learn Instruction

01-34753A

APPLICATION REQUIREMENTS:

This instruction is intended for use with the SL595 Variable Speed operators as a supplemental instruction to the standard

SL595 manual, 01-34850. All other installation, programming, and configuration information should refer to the 01-34850

manual.

PROGRAMMING INSTRUCTIONS

BEFORE STARTING

Before starting, the operator should be correctly installed

and connected to the gate. The gate operator should

not be run until after the motor is learned. The limit nut

should be adjusted so that the gate can travel several

feet in either direction without hitting a limit.

MOTOR LEARN FUNCTION (FORCE

PROFILE)

In order to accurately set the force control for the

operator, the control board must “learn” the specific RPM

profile for your operator. This is done using the red

button, “S3”, located at the end of the control board, next

to the microprocessor.

NOTE: Motor learn must be performed in stand alone

mode while running at its slowest speed setting as set by

the main speed potentiometer. The gate must be

correctly installed and connected to the operator.

1. Set the gate speed to the slowest setting by turning

the main speed potentiometer (located in front of the

small control board) fully counter-clockwise.

2. Press the motor learn button (S3) on the main control

board. The yellow LED should start to flash rapidly.

3. Push and hold down either the open or the close

buttons. The motor will run for a few seconds and

then stop. If the LED goes out the motor is learned.

If the unit hits a limit before completing the learn

sequence or some other error occurs, the LED will go

back to “on” continuously. If this happens, try

learning the motor in the opposite direction.

COMPLETING THE INSTALLATION

The limits and other aspects of the operator can be

configured at this time. Refer to the main operator

manual, 01-34850, for these instructions.

After the limits are set and the gate is operating as

intended, the main speed potentiometer can be adjusted

as desired. Verify that the gate can run the full open and

close distances without incident after adjusting the main

speed potentiometer.

NOTE: If the gate cannot move at full speed without

stopping, the motor profile must be re-learned at a

higher minimum speed. To do this, increase the

minimum speed by turning the Min Speed Trimpot

clockwise. Adjust the Main Speed Potentiometer to its

minimum setting (fully counter clockwise) and repeat the

motor learn process.

Min Speed

Trimpot

Main Speed

Potentiometer

Inhaltsverzeichnis

Andere Chamberlain Garagentoröffner Handbücher

Chamberlain

Chamberlain Infinity B Bedienungsanleitung

Chamberlain

Chamberlain Merlin MT60P Bedienungsanleitung

Chamberlain

Chamberlain LM50 Bedienungsanleitung

Chamberlain

Chamberlain MT5011U Bedienungsanleitung

Chamberlain

Chamberlain RJO Bedienungsanleitung

Chamberlain

Chamberlain MyQ 8550W Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Premium 8355 Bedienungsanleitung

Chamberlain

Chamberlain LIFTMASTER 373LM Bedienungsanleitung

Chamberlain

Chamberlain 2565 1/2 HP Bedienungsanleitung

Chamberlain

Chamberlain LM800A Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive Security+ 248739L Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional Security+ 3800 Bedienungsanleitung

Chamberlain

Chamberlain merlin MT23O Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster CRX100 Bedienungsanleitung

Chamberlain

Chamberlain Security+ 8200 Series Bedienungsanleitung

Chamberlain

Chamberlain 1200 Bedienungsanleitung

Chamberlain

Chamberlain 3750E-1A Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive Security+ WD962KD Bedienungsanleitung

Chamberlain

Chamberlain Series OCG Bedienungsanleitung

Chamberlain

Chamberlain GH Bedienungsanleitung

Chamberlain

Chamberlain MGJ Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster ATS 2113X Bedienungsanleitung

Chamberlain

Chamberlain HD220C Bedienungsanleitung

Chamberlain

Chamberlain GH Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Craftsman

Craftsman 139.53997D Bedienungsanleitung

Bauer

Bauer CROSS18 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8124 Kurzanleitung

Craftsman

Craftsman 139.18867 Bedienungsanleitung