Chamberlain SMART GARAGE MYQ-G0301 Bedienungsanleitung

Smart Garage™Hub

Manual

MYQ-G0301 • MYQ-G0301C

MYQ-G0301-D • MYQ-G0301LA

Smart Garage™Hub

Manual

For Android™

devices

- 2 -

Read instructions thoroughly BEFORE beginning.

If using this product with residential door openers, this product must be used only with door openers

manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located

on or near the bottom of the door track.

Before you start, you MUST have…

• A router with 2.4GHz Wi-Fi® frequency

• Router congured with 802.11 B/G/N

• Router within 50 ft. of MyQ Smart Garage Hub

• Mobile phone connected to your home Wi-Fi network

• Home Wi-Fi network password

• Latest version of MyQ App

• Compatible garage door opener (see Compatible Garage Door Openers on page 20)

• Locate program or learn button on the garage door opener

See Appendix on page 21 for a more detailed list of program or learn button locations.

To reduce the risk of SEVERE INJURY to persons:

• DO NOT enable the MyQ® Smart Garage™ Hub if operating either one-piece or swinging doors. To be enabled

ONLY on a sectional door.

Before You Start

Program Button

LED

WARNING: This product can expose you to chemicals including lead, which are known to the State of California

to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

- 3 -

Wi-Fi Hub

Door Sensor

Model MYQ-G0302

Power Adapter

Hardware for Wi-Fi Hub

(5/32" x 1-1/2" screws)

Mounting bracket

Hardware for

Door Sensor

(5/32" x 3/4" screws

)

Fastening Strips for

Door Sensor

Warning Label

(not shown)

Blue LED

Red

LED

Test

Button

Green LED

Yellow LED

What’s in the Box

Tools Needed: Drill, 5/32" Drill Bit, Screwdriver, Ladder

MyQ Smart Garage Hub

Blue LED

Light

Door Sensor

Fastening Strips for

Door Sensor

Hardware for

Door Sensor

(5/32” x 3/4” screws)

Warning Label

(not shown)

Hardware for

MyQ Smart Garage Hub

(5/32” x 1-1/2” screws)

Mounting bracket

Power Adapter

Test Button

Green LED

Yellow LED

Before You Start

- 4 -

Step 1: Check your Wi-Fi signal

Make sure your mobile phone is connected to your Wi-Fi network. Hold the mobile phone near where you plan to

install the MyQ Smart Garage Hub.

If you see:

Wi-Fi signal is strong. You’re all set! Proceed to next step.

Wi-Fi signal is weak. The MyQ Smart Garage Hub may not connect to your Wi-Fi network. If it doesn’t

connect, try one of the options below.

No Wi-Fi signal. Try one of the following options:

• Move your router closer to the garage to minimize interference from walls and other objects.

• Buy a Wi-Fi range extender.

To watch a video on How to test your Wi-Fi Signal Strength before setting up your MyQ® product,

go to youtu.be/_Ow1wVF-7AU

Wireless Setup and Installation

(mounting area)

MyQ Smart Garage Hub

mounting area

- 5 -

Step 2: Install door sensor

1. Remove the pull tab from the door sensor to activate the battery.

2. Test the door sensor by pushing the test button and conrming the LED on the door sensor blinks.

If the LED on the door sensor does not blink, see Troubleshooting on page 16.

3. Install the door sensor on the top panel of the garage door using the fastening strips or provided hardware.

IMPORTANT: Door sensor MUST be installed to read “myQ” lettering right-side up.

Step 3: Download the MyQ® App

If you already have the MyQ App, verify you have the latest version. To conrm you have the

latest version of the app, go to Google PlayTM store and search for the Chamberlain MyQ App.

If you see Update, tap Update.

Wireless Setup and Installation

Door Sensor

LED

“TOP” MUST

always face UP

Test

Button Fastening

Strips

Screws

CR2450 Battery

Press

- 6 -

If you have already registered a MyQ account, skip this step and login.

Step 4: Create and Register your MyQ Account

1. Open the MyQ App and tap Sign Up.

2. Enter rst name, last name, valid email address, and password

(twice), country, and zip code.

NOTES:

• Check email address for errors.

• Use a valid email address you can access.

• If the email address you are attempting to use is already in the

MyQ system, you will receive an error message.

• If necessary, tap Forgot Password to retrieve the password

for that email and login. For more information, see

Troubleshooting on page 16.

3. Tap Submit (top right-hand corner). An email will be sent to the

email address you provided.

5. Open the email from Chamberlain support and tap the link to

complete your registration. The MyQ App will open, verifying

registration of email address was successful. NOTE: If you didn’t

receive an email, check the Junk or Spam folder.

6. Tap OK.

7. Enter your email address and password and tap Login.

Congratulations! Registration of your account is now complete.

Wireless Setup and Installation

- 7 -

Blue LED blinks

Step 6: Login to MyQ App

Enter the email and password you used to register your account and

tap Login.

TIP: Select Remember Me if you want the MyQ App to remember

your email address and password. You can change the security

settings within the MyQ App by tapping the menu bar in top-left

corner and then your name on bottom-left to access settings.

Blue LED blinks

MyQ Smart Garage Hub

Wireless Setup and Installation

Settings Button

Step 5: Power up the MyQ Smart Garage Hub

Find a convenient location and plug in the MyQ Smart

Garage Hub. Wait for the blue LED to blink.

If blue LED is not blinking:

Unplug and plug back in.

If the blue LED still does not blink, reset to factory

default:

1. Press and hold the Settings button until the

blue LED blinks (about 10 seconds) then release.

2. Press and hold Settings button again until the

MyQ Smart Garage Hub beeps.

IMPORTANT NOTE: Resetting the MyQ Smart Garage

Hub to factory default erases the Wi-Fi settings, erases

door sensors, and removes the MyQ Smart Garage Hub

from the currently paired MyQ account.

- 8 -

Wireless Setup and Installation

In the MyQ App:

1. Tap Get Started or tap “+”.

3. Tap YES to connect your MyQ Smart Garage Hub

to your Wi-Fi network.

2. Tap “MyQ-nnn” under Discoverable Devices.

Step 7: Connect the Smart Garage Hub to the Wi-Fi Network

- 9 -

Wireless Setup and Installation

Step 7: Connect the Smart Garage Hub to your Wi-Fi Network continued

4. Select your home Wi-Fi network from the list. 5. Enter your home Wi-Fi network password and tap Connect.

Wait for the solid green LED on your MyQ Smart Garage

Hub. This can take up to 2 minutes.

Result: LED is solid green. NOTE: If the LED is not solid

green, see Troubleshooting on page 16.

6. Enter a name for your MyQ Smart Garage Hub and

tap Save.

- 10 -

Wireless Setup and Installation

Step 8: Add New Device

Now that your MyQ Smart Garage Hub is connected to your home Wi-Fi network, the next steps will guide you through

the process of pairing your garage door opener to your MyQ Smart Garage hub.

TIP: A device is any MyQ accessory that can be paired with your MyQ Smart Garage hub for monitoring and control. This

includes MyQ Lighting accessories and an add-on door sensor that expands your MyQ functionality to a second garage door.

The following steps are to add a garage door opener.

1. Conrm your door sensor is mounted and tap Next.

3. Press and release the test button on the door sensor.

The MyQ Smart Garage Hub will beep and the light

will ash.

Door Sensor

Red

LED

Test

Button

MyQ Smart Garage Hub

Light

2. Locate the test button on the door sensor and tap

Next.

Andere Handbücher für SMART GARAGE MYQ-G0301

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chamberlain Garagentoröffner Handbücher

Chamberlain

Chamberlain Power Drive PD200C Bedienungsanleitung

Chamberlain

Chamberlain Icon 26 Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chamberlain

Chamberlain merlin MT5580P Bedienungsanleitung

Chamberlain

Chamberlain J Bedienungsanleitung

Chamberlain

Chamberlain 98022 Bedienungsanleitung

Chamberlain

Chamberlain Merlin Whisper Drive MT3850EVO Bedienungsanleitung

Chamberlain

Chamberlain 4000 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster LM800A-2 Gebrauchsanweisung

Chamberlain

Chamberlain 821LM Bedienungsanleitung

Chamberlain

Chamberlain RollerLift Plus Bedienungsanleitung

Chamberlain

Chamberlain 2265C Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive Security+ 248739 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster LM3800A Bedienungsanleitung

Chamberlain

Chamberlain Power Drive PD752 Bedienungsanleitung

Chamberlain

Chamberlain HD220 Bedienungsanleitung

Chamberlain

Chamberlain 3800C Bedienungsanleitung

Chamberlain

Chamberlain 821LM Bedienungsanleitung

Chamberlain

Chamberlain MT5011U Bedienungsanleitung

Chamberlain

Chamberlain Merlin MT60P Bedienungsanleitung

Chamberlain

Chamberlain K72-16421 Bedienungsanleitung

Chamberlain

Chamberlain APT Montage- und Bedienungsanleitung

Chamberlain

Chamberlain Liftmaster ATS 211X Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Security+ 2500BC Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung

Craftsman

Craftsman 139.53997D Bedienungsanleitung

Bauer

Bauer CROSS18 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8124 Kurzanleitung

Craftsman

Craftsman 139.18867 Bedienungsanleitung