Chamberlain GAILM Bedienungsanleitung

Carton Inventory

Overview

The Gate Access Intercom can be used as either a

primary or secondary door and gate access point. It

can be used to control electric gates, entry doors, or

pedestrian doors with electric strikes. The Intercom

uses a secure digital connection that allows it to

operate without interfering with other Intercom

networks.

The Intercom is compatible with various Liftmaster

Wireless Products.

Setup

Intercom

Model GAILM

Gate Access Intercom

Bolt (4)

Washer (4)

Nut (4)

Screw (4)

Allen Wrench

Install 4 AA Alkaline

batteries (not provided).

(Lithium batteries

recommended for colder

environments.)

Install Batteries

Set Dipswitches

Primary Intercom: Switch #1 is set to

the UP position (default).

Secondary Intercom: Switch #1 is set

to the DOWN position.

Gate Control Unit (GCU) (not provided)

NOTE: This step applies only if Intercom is going to

control a gate or electric strike. If not, proceed to

Program Accessories.

Set the Dipswitches on the Intercom to match the

GCU number to be controlled:

Control Dipswitch Dipswitch

Gate # #1 #2

1 DOWN DOWN

2 UP DOWN

3 DOWN UP

Refer to GCU manual for GCU Dipswitch settings.

Step 2: Install 4 AA Alkaline

batteries (not provided). (Lithium

batteries recommended for colder

environments.)

Step 1: Remove GCU cover.

Step 3: Press the Learn button on

the GCU for one second. The LED

will light for 20 seconds.

Program Intercom to GCU

Step 4: Within 20 seconds, press

and hold the Learn button for 10

seconds.

The Intercom will beep and the GCU will

cycle the relay and flash 3 times indicating

programming is successful.

NOTE: If there is already an existing receiver proceed

to Pre-Installed LiftMaster Receiver section.

NOTE: If there is already an existing receiver proceed

to Pre-Installed LiftMaster Receiver.

Program Accessories

Telephone Interface Unit (OTIU)

NOTE: If the Intercom is set as the Secondary

Intercom, there is no need to program it to any

accessory.

To clear the memory on the OTIU, dial “**#8” on the

telephone connected to the OTIU. A beep will be

heard.

Step 1: On the phone connected to the OTIU, press

“**07” after hearing the dial tone. Listen for a double

beep. Hang up and Learn LED will flash for 15

seconds.

Step 2: Within 15 seconds, press and release the

Learn button on the Intercom.

The OTIU will ring the telephone and Caller ID will

display “Unit Learned”.

Refer to OTIU manual for more details.

To clear Portable Intercom memory, press and hold

Learn button until a beep is heard.

Step 1: Press and hold the Learn button on the

Intercom until a beep is heard.

Step 2: Within 15 seconds, press and release the

Learn button on the Portable Intercom.

Intercom will beep indicating programming is

successful.

Program any additional intercoms to the Portable

Intercom that has already been programmed.

Refer to Portable Intercom manual for more details.

To clear Flush Mount Intercom memory, press and

hold both buttons. Two beeps will be heard and the

channel lights will begin to cycle. Continue to hold

until a third beep is heard (about 15 seconds).

Step 1: Press and hold the Learn button on the

Intercom until a beep is heard.

Step 2: Within 20 seconds, press and hold both

buttons on the Flush Mount Intercom for 3 seconds.

The LEDs will flash.

Intercom will beep indicating programming is

successful.

Program any additional intercoms to the Flush Mount

Intercom that has already been programmed.

Pre-Installed Liftmaster

Receiver

Step 1: Pry open the front

panel of the receiver case

with a coin or a

screwdriver.

Step 2: Set Dipswitch #1 to

the UP position on the

Intercom.

Step 3: Press and release the

Learn button on the receiver. The

Indicator Light will light for 30 seconds indicating that

receiver is in Learn Mode.

Step 4: Within 30 seconds, press and release the

Learn button on the Intercom for 10 seconds.

Repeat Steps 2-4 for each remote, or control device

that will be used to access the Liftmaster door or gate

operator.

Program

Erase All Control Codes

Press and hold the Learn button on the receiver until

the Indicator Light turns off indicating that the receiver

memory is clear (about 6 seconds).

Indicator Light

Learn Button

Flush Mount Intercom

Portable Intercom

Operation

Mount Intercom

Step 1

Choose mounting location for Intercom. Remove the

back panel and attach it to a solid surface or post.

Mount the Intercom onto the back panel with screws.

Tighten screws with Allen wrench.

Step 2

It is recommended that the Intercom be mounted to a

Gooseneck post or non-metallic surface.

NOTE: Metal surfaces can shorten the range of the

Intercom. If mounting on a metal surface and long

range is required, use a non-metallic spacer to move

the Intercom away from the metal surface.

The Intercom is waterproof so that rain or high

humidity will not effect it. However, do not mount

Intercom in the direct path of a sprinkler system as

the Intercom’s life can be reduced.

Battery: The AA batteries (not provided) will last up to

two years depending on use (Lithium batteries

recommended for colder environments.) If batteries

are low, the intercom will emit a tone every ten

minutes.

If used with the OTIU, the OTIU will ring the

telephone and display Caller ID message of

GAPLM low battery after a call from the gate is made.

Volume: To increase the speaker

volume, set Dipswitch #4 to the UP

position.

Sensitivity: To increase microphone

sensitivity, set Dipswitch #3 to the UP

position.

Clear Memory: Set Dipswitch #1 to

the DOWN position (secondary

device mode). Press and hold the

Learn button for 15 seconds, during

this time the Intercom may beep (once

or consecutively). Continue to hold until

a long beep is heard.

Program Secondary Intercom

NOTE: This step applies only if there is a Secondary

Intercom. If not, proceed to Mount Intercom.

Step 1: Set Dipswitch #1 to the DOWN position on

the Secondary Intercom.

Step 2: Press the Learn button on the Primary

Intercom.

Step 3: Within 15 seconds, press the Learn button on

the Secondary Intercom.

Intercom will beep indicating programming is

successful. Secondary Intercom is now connected to

the whole network.

Gate Access Panel (GAPLM)

Step 1: Set Dipswitch #1 to the DOWN position on

the Secondary Intercom.

Step 2: Press the Learn button on the Secondary

Intercom.

Step 3: Within 20 seconds enter Master PIN Number

on GAPLM.

Step 4: Press “05” and GAPLM will beep indicating

programming is successful.

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this receiver and/or transmitter are prohibited,

except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:

1-800-528-2806

www.liftmaster.com

Troubleshooting

When it gets cold, Intercom does not function.

In this case, use AA Photo Lithium batteries, which

are 1.5V each. They will also extend battery life.

Intercom is not getting expected transmission

range.

Metal surfaces can shorten the range of the Intercom.

If mounting on a metal surface and long range is

required, use a non-metallic spacer to move the

Intercom away from the metal surface.

When used in buildings with stucco or cement walls,

the range is greatly reduced. Repeaters can be used

close to the building to solve this problem.

Repeaters can also be used if there is a 900 Mhz

noise source nearby that is affecting the range.

When using with Repeaters, the sound is not

clear.

Ensure that the Repeaters are properly programmed.

To test, remove the batteries from one Repeater. If

the remaining Repeater is working, switch the

batteries and test the other Repeater. If one of the

Repeaters does not work, it means if has not been

programmed. Both Repeaters must be programmed

for the system to work.

Intercom is too loud/not loud enough.

Adjust Dipswitch #4 as explained in the Operation

section.

Intercom is too sensitive/not sensitive enough.

Adjust Dipswitch #3 as explained in the Operation

section.

Inhaltsverzeichnis

Andere Chamberlain Gegensprechanlage Handbücher

Chamberlain

Chamberlain LiftMaster Professional RIFM1LM Bedienungsanleitung

Chamberlain

Chamberlain 75EV Bedienungsanleitung

Chamberlain

Chamberlain ELITE EL2000LG Betriebsanleitung

Chamberlain

Chamberlain LiftMaster FDI Bedienungsanleitung

Chamberlain

Chamberlain RIFMS2 Bedienungsanleitung

Chamberlain

Chamberlain Icon26 series Bedienungsanleitung

Chamberlain

Chamberlain Elite EL25N Bedienungsanleitung

Chamberlain

Chamberlain WIRELESS PORTABLE INDOOR/OUTDOOR INTERCOM... Bedienungsanleitung

Chamberlain

Chamberlain myQ Business CAPXM Bedienungsanleitung

Chamberlain

Chamberlain EL1SS Montageanleitung

Chamberlain

Chamberlain LiftMaster 833-1LM Bedienungsanleitung

Chamberlain

Chamberlain RWIA Bedienungsanleitung

Chamberlain

Chamberlain WIRELESS GATE ACCESS RGAIPI Bedienungsanleitung

Chamberlain

Chamberlain LIFTMASTER MUGAPLM Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster ELITE EL25 Bedienungsanleitung

Chamberlain

Chamberlain 845EML Bedienungsanleitung

Chamberlain

Chamberlain OPI Bedienungsanleitung

Chamberlain

Chamberlain ROI2 Bedienungsanleitung

Chamberlain

Chamberlain TAC11 Montageanleitung

Chamberlain

Chamberlain Smart Video Intercom M Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster ELITE EL25 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster ELITE EL25 Bedienungsanleitung

Chamberlain

Chamberlain MyQ Business CAPXL Bedienungsanleitung

Chamberlain

Chamberlain WIRELESS PORTABLE INDOOR/OUTDOOR INTERCOM... Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung