Chamberlain KPR2000 Benutzerhandbuch
For How-to videos, visit the LiftMaster Training Academy
at LiftMasterTraining.com
Installation
and Set Up Manual
KPR2000
Waterproof
Keypad/Proximity Reader
123
456
789
*
0
#
Para Manual en Español ir a:
http://www.LiftMaster.com/CatalogResourcesV3/en-us/shared/files/
tucmanuals/0137261SP.pdf
2
INTRODUCTION. . . . . . . . . . . . . . 2-4
Specifications. . . . . . . . . . . . . . . . . . . . 2
Features . . . . . . . . . . . . . . . . . . . . . . . . 3
Accessories . . . . . . . . . . . . . . . . . . . . . 3
One Year Limited Warranty . . . . . . . . . 3
Carton Inventory . . . . . . . . . . . . . . . . . 4
INSTALLATION . . . . . . . . . . . . . . 5-6
Install the KPR2000. . . . . . . . . . . . . . . 5
Choose an Operation Mode. . . . . . . . . 6
WIRING . . . . . . . . . . . . . . . . . . 7-10
Wire the KPR2000. . . . . . . . . . . . . .7-10
SET UP . . . . . . . . . . . . . . . . . .11-22
Configure the KPR2000. . . . . . . . .11-14
Program Cards and PINS. . . . . . . .15-19
Alarm . . . . . . . . . . . . . . . . . . . . . . . . . 20
Reset the KPR2000 . . . . . . . . . . . . . . 21
Erase all Codes . . . . . . . . . . . . . . . . . 21
Sound & Light Indication. . . . . . . . . . 22
SPECIFICATIONS
User Capacity......................... 2000 User ID's with card and/or PINS
Operating Voltage ................... 12 ~ 24 Vdc or 12 ~ 18 Vac
Idle Current....................... ~ 50mA
Active Current .................... ~ 80mA
Keypad................................. 12 Key (3x4)
Two output formats ............. 26 bit Wiegand Card keypad mode, 8 bit ASCII keypad mode
Proximity Card Reader.............. HID 26 bit and 30 bit (Sentex)
Radio Technology.....................125 KHz Industry Standard Proximity Card
Read Range .............................. 1 inch - 2.5 inches
Wiring Connections........................Relay Output, REX, DOTL, Alarm, Wiegand (in/out)
Relay ..............................................One (NO, NC, Common)
Adjustable Relay Output Time.... 1 ~ 99 Seconds (5 seconds default)
Adjustable Auxiliary
Alarm Output Time ................... 0 ~ 3 Minutes (1 minute default)
Lock Output Load .....................2 Amp Maximum
Auxiliary Alarm Output Load.....10 Amp Maximum
Wiegand Interface ................... HID Wiegand 26 and 30 bit Format Input & Output
Environment .......................... Meets or exceeds IP68
Operating Temperature.............-20°C ~ 60°C, or -4°F ~ 140°F
Operating Humidity...................10% ~ 90% Non-Condensing
Physical ............................... Zinc-Alloy Enclosure
Surface Finish...........................Powder Coat
Dimensions...............................L:128mm x W:82mm x D:28mm
Unit Weight...............................1 Pound
Shipping Weight .......................1.4 Pounds
INTRODUCTION INSTALLATION WIRING SET UP
3
FEATURES
• Waterproof (IP68)
(meets or exceeds N4)
• Vandal Resistant Enclosure
• Blue Backlit Keypad
• Multi-color LED status display
• Integrated Alarm Buzzer & Output
• One Programmable Relay Output
• Stand Alone or Pass-Through
Operation
• 2000 Users (Card/PIN/Card+PIN)
• Low power consumption (50mA)
• Anti-Tamper Alarm
• Latch Mode to hold door or gate open
• Two Keypad Operating Modes
• Time Saving Block Card Enrollment
ACCESSORIES (Sold Separately)
• Model PS12D2A 12 Vdc, 2 Amp
Power Supply
• Model 142A0271 Decorative Trim
Plate
• Model PED42 Gooseneck Pedestal
• Model PED64 Gooseneck Pedestal
• Model LMPC2-ST HID 26 Bit
Proximity Clamshell Card
• Model LMPK3-ST HID 26 Bit
Proximity Key
The LiftMaster KPR2000 is a single entry multi-function Access Controller with
integrated keypad and card reader. It is designed and manufactured to perform in a
wide range of indoor, outdoor, and harsh environments.
The KPR2000 supports up to 2000 users in multiple access configurations (Card Only,
Card or PIN, or Card + PIN). The built in 125 KHz card reader supports HID 26 bit
Wiegand and 30 bit Sentex Wiegand proximity card formats. The KPR2000 offers
advanced programming features like; block enrollment, advanced relay programming,
and Panic PINs/Cards (which open the entry and set off the alarm).
INTRODUCTION INSTALLATION WIRING SET UP
ONE YEAR LIMITED WARRANTY
LiftMaster warrants to the first consumer purchaser of this product that it is free from
defect in materials and/or workmanship for a period of 1 year from the date of purchase.
4
NOTICE: This device complies with part 15 of the FCC rules and Industry Canada (IC) license-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
This device must be installed in a way where a minimum 8" (20 cm) distance is maintained between users/
bystanders and device.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INTRODUCTION INSTALLATION WIRING SET UP
CARTON INVENTORY
NOT SHOWN: Manual
KPR2000
Keypad/Proximity Reader/Controller
Diode IN4007 (For Relay
circuit protection)
Self Tapping Screws #8 x 1"
Wall Anchors #6 x 1 1/8"
Manager Add Card
Manager Delete Card
Security Screwdriver
(T-10 Security Torx Driver)
5
Trim Plate (142A0271)
(optional)
Face Plate
Ø 1.81"
(4.6 cm)
.29" (.74 cm)
3" 7.6 cm)
2.4" (6.1 cm)
4" (10.2 cm)
4" (10.2 cm)
INTRODUCTION INSTALLATION WIRING SET UP
INSTALL THE KPR2000
The KPR2000 fits a standard single outlet box, or a 2.4" (6.1 cm) square pedestal
mount.
6
INTRODUCTION INSTALLATION WIRING SET UP
CHOOSE AN OPERATION MODE
STAND ALONE OPERATION (KPR2000 WITH A GATE OPERATOR)
The KPR2000 functions as a complete access control system. The user database is
stored in non-volatile memory, reads the PINs and card codes, performs the
authentication, and grants and monitors access to the property or device. In Stand
Alone Operation there are three different Access Configurations listed below:
• Card or PIN (Default): The User must present a valid Wiegand Card to the
KPR2000 or enter their PIN code followed by the # key, in order to be granted
access.
• Card Only: The User must present a valid Wiegand Card to the KPR2000 in order
to be granted access. The facility code and the ID number are both read and
validated as one block of Wiegand data.
• Card + PIN: The User must first present a valid Wiegand Card to the KPR2000
and then enter their PIN code followed by the # key, in order to be granted
access.
PASS-THROUGH OPERATION (KPR2000 WITH TELEPHONE ENTRY SYSTEM)
The KPR2000 passes all keypad and card reader Wiegand data to an external
controller. The KPR2000 should be in the “Card or PIN” access configuration for
pass-through operation. In this mode the LED will stay red, and the KPR2000 will
beep 3 times when credentials are presented that are authenticated to the external
controller. To change this mode and allow the KPR2000 to flash the green LED, and
beep 1 time, the KPR2000 will have to learn the same credentials as the external
controller.
IMPORTANT NOTE: Both modes of operation support Auto User ID generation
(simplest method) and manual entry of user ID.
KEYPAD OPERATION
The KPR2000 keypad may output an 8 bit ASCII code every keystroke, or output a
26 bit Wiegand card packet with a facility code and a 4-5 digit card number when the
# key is pressed. See configuration options on page 11.
7
Wire Insulation
Color
Wiring
Function
Notes
BASIC STAND ALONE WIRING (WITH A GATE OPERATOR)
Red Power 12 - 24 Volts DC or 12 - 18 Volts AC regulated power input
Black Power 12 - 24 Volts DC or 12 - 18 Volts AC regulated power input
Blue Relay NO Normally Open Relay Output (Install diode) provided)
Purple Relay
Common Common Connection for Relay Output
Orange Relay NC Normally Closed Relay Output (Install diode[provided])
CONNECTING TWO KPR2000 UNITS
Red Power 12 - 24 Volts DC or 12 - 18 Volts AC regulated power input
Black Power 12 - 24 Volts DC or 12 - 18 Volts AC regulated power input
Green Data 0 Wiegand Output (Pass-through)/Input (Stand Alone) Data 0
White Data 1 Wiegand Output (Pass-through)/Input (Stand Alone) Data 1
Pink Ground Ground reference for Wiegand Output/Input
ADVANCED INPUT AND OUTPUT FEATURES
Yellow REX Request To Exit (REX) Input
Gray Alarm Output Negative contact for Alarm
Brown Contact Input Door/Gate Contact Input (Normally Closed)
Pink Ground Ground reference for REX, and Door/Gate contact inputs.
ACCESS CONTROL SYSTEM
Red Power 12 - 24 Volts DC or 12 - 18 Volts AC regulated power input
Black Power 12 - 24 Volts DC or 12 - 18 Volts AC regulated power input
Pink Ground Ground reference for Wiegand Output/Input
Green Data 0 Wiegand Output (Pass-through)/Input (Stand Alone) Data 0
White Data 1 Wiegand Output (Pass-through)/Input (Stand Alone) Data 1
INTRODUCTION INSTALLATION WIRING SET UP
WIRE THE KPR2000
8
WIRING EXAMPLES:
Connecting to an Access Control System
INTRODUCTION INSTALLATION WIRING SET UP
Pink
Black
White
Green*
Red Power
*Maximum of 500 feet
(152.4 m)
(Same distance limitations
as used for networking 2
KPR2000's)
OR AC or DC
Power Supply
(+) and (-) shown
for DC applications
Black (DC -)
Red (DC +)
Pink
White
Green
The example below uses the EL25/EL2000SS Wiegand Module (WOMDKT).
KPR2000 can be connected to other access systems with the same Wiegand inputs.
KPR2000 can be connected to Device 1, 2, 3 or 4 (EL25, EL2000SS).
Acc +
Acc -
Exit +
Exit -
Red
Black
Blue
Purple
Connecting to a Gate Operator
4-wire connection with KPR2000 powered from the CSL24U/CSW24U/LA500PKGU/
LA400PKGU accessory power output.
9
Red
Black
Normally Open
Blue
Purple
Gray
Pink
For DC Power:
Install a 1N4007 or
equivalent diode.
(1 Amp Maximum)
For AC Power:
S10K30MOV
(Metal Oxide Varistor)
(not provided)
AC or DC
External Alarm
Brown Door Contact
KPR2000
Request to Exit
(+) and (-) shown
for DC applications
Yellow
Red
Black
Orange
Purple
Normally Closed
Gray
(1 Amp Maximum)
Pink
Yellow
Brown Door Contact
Request to Exit
For DC Power:
Install a 1N4007 or
equivalent diode.
For AC Power:
S10K30MOV
(Metal Oxide Varistor)
(not provided)
AC or DC
External Alarm
(+) and (-) shown
for DC applications
KPR2000
Magnetic Lock or
Fail-Safe Strike
INTRODUCTION INSTALLATION WIRING SET UP
WIRING EXAMPLES:
Door Operator or
Fail-Secure Strike
10
Green (Data 0)
Maximum of 500 feet (152.4 m)
White (Data 1)
Maximum of 500 feet (152.4 m)
Pink
(must connect for ground reference)
Maximum of 500 feet (152.4 m)
Red
Black
Normally Open
Blue
Purple
Gray
Pink
(1 Amp Maximum)
Black
Pink
Red
For DC Power:
Install a 1N4007 or
equivalent diode.
For AC Power:
S10K30MOV
(Metal Oxide Varistor)
(not provided)
KPR2000 Stand-Alone
(Master Unit)
KPR2000 Stand-Alone
(Remote Unit)
(+) and (-) shown
for DC applications
AC or DC
AC or DC
External Alarm
WIRING EXAMPLES:
Networking Two KPR2000 Units
INTRODUCTION INSTALLATION WIRING SET UP
Andere Handbücher für KPR2000
2
Inhaltsverzeichnis
Sprachen:
Andere Chamberlain Tastenfeld Handbücher
Chamberlain
Chamberlain LiftMaster Professional 387LM Bedienungsanleitung
Chamberlain
Chamberlain LiftMaster ELITE EL25 Bedienungsanleitung
Chamberlain
Chamberlain LiftMaster ELITE EL25 Betriebsanleitung
Chamberlain
Chamberlain 747EML Series Bedienungsanleitung
Chamberlain
Chamberlain KPR2000 Bedienungsanleitung
Chamberlain
Chamberlain LiftMaster Security+ WKP5LM Bedienungsanleitung
Chamberlain
Chamberlain KPW250 Bedienungsanleitung
Chamberlain
Chamberlain Clicker KLIK2U Bedienungsanleitung
Chamberlain
Chamberlain 780EV Bedienungsanleitung
Chamberlain
Chamberlain Clicker KLIK2U Bedienungsanleitung
Chamberlain
Chamberlain Clicker KLIK2U Bedienungsanleitung
Chamberlain
Chamberlain LiftMaster Professional 387LM Bedienungsanleitung
Chamberlain
Chamberlain Clicker KLIK2U Bedienungsanleitung
Chamberlain
Chamberlain 920GA Bedienungsanleitung
Chamberlain
Chamberlain WKP5LM3 Bedienungsanleitung
Chamberlain
Chamberlain KPW5 Bedienungsanleitung
Chamberlain
Chamberlain LiftMaster Q Bedienungsanleitung
Chamberlain
Chamberlain LiftMaster Security+ WKP250LM Bedienungsanleitung
Chamberlain
Chamberlain KPR2000 Bedienungsanleitung
Chamberlain
Chamberlain LiftMaster TAC2C Bedienungsanleitung
