Chamberlain 950ESTD-P2 Bedienungsanleitung

TO ERASE ALL CODES FROM MEMORY

REMOTE CONTROL

MODEL 950ESTD-P2

To prevent possible serious injury or death from a moving gate or garage door:

•ALWAYS keep remote controls out of reach of children. NEVER permit children to operate,

or play with remote controls.

•Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are

no obstructions to door travel.

•ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to

cross path of moving gate or door.

Press and hold the button

on the remote control.

“click”

Release the button

when the garage

door opener lights

blink or two clicks

are heard.

Locate the

LEARN button. Press and

immediately release

the LEARN button.

The LEARN LED will glow

steadily for 30 seconds.

Within 30 seconds...

With the door closed,

press and hold

the remote

control button to

control the light.

Press and

hold the

LIGHT button

on the

door control.

Press and

hold the

LOCK button

on the

door control.

After the garage

door opener

lights ﬂash,

release all

buttons.

“click”

Press and hold the LEARN button on garage door

opener or other product until the LEARN LED goes out

(approximately 6 seconds). All previous codes are

now erased. Reprogram each remote control you

wish to use.

Press the LEARN button again,

the LED will ﬂash once.

Press the LEARN button on

the door control to enter

Programming Mode.

The command LED

will ﬂash once. The command LED

will ﬂash once again.

Press and hold the button

on the remote control. Release the button when

the garage door opener

lights blink or two clicks

are heard.

“click”

For use with Security+ 2.0®Garage Door Openers which have a yellow LEARN button and yellow

antenna wire, and are manufactured after 2010. The code between the remote control and the

receiver changes with each use, randomly accessing over a billion new codes. Refer to your

product manual for the location of the LEARN button.

NOTE: Your product may look different than the products illustrated in this manual.

When deactivating any unwanted remote

control codes, all previous codes will be

erased. All additional accessories will

also be erased. Refer to your product

manual for more information.

Press and hold the button

on the remote control.

“click”

Release the button

when the garage

door opener lights

blink or two clicks

are heard.

Locate the

LEARN button. Press and

immediately release

the LEARN button.

The LEARN LED will glow

steadily for 30 seconds.

Within 30 seconds...

With the door closed,

press and hold

the remote

control button to

control the light.

Press and

hold the

LIGHT button

on the

door control.

Press and

hold the

LOCK button

on the

door control.

After the garage

door opener

lights ﬂash,

release all

buttons.

“click”

Press and hold the LEARN button on garage door

opener or other product until the LEARN LED goes out

(approximately 6 seconds). All previous codes are

now erased. Reprogram each remote control you

wish to use.

Press the LEARN button again,

the LED will ﬂash once.

Press the LEARN button on

the door control to enter

Programming Mode.

The command LED

will ﬂash once. The command LED

will ﬂash once again.

Press and hold the button

on the remote control. Release the button when

the garage door opener

lights blink or two clicks

are heard.

“click”

LED

PROGRAM USING THE GARAGE DOOR OPENER

PROGRAM USING THE DOOR CONTROL

Press and hold the button

on the remote control.

“click”

Release the button

when the garage

door opener lights

blink or two clicks

are heard.

Locate the

LEARN button. Press and

immediately release

the LEARN button.

The LEARN LED will glow

steadily for 30 seconds.

Within 30 seconds...

With the door closed,

press and hold

the remote

control button to

control the light.

Press and

hold the

LIGHT button

on the

door control.

Press and

hold the

LOCK button

on the

door control.

After the garage

door opener

lights ﬂash,

release all

buttons.

“click”

Press and hold the LEARN button on garage door

opener or other product until the LEARN LED goes out

(approximately 6 seconds). All previous codes are

now erased. Reprogram each remote control you

wish to use.

Press the LEARN button again,

the LED will ﬂash once.

Press the LEARN button on

the door control to enter

Programming Mode.

The command LED

will ﬂash once. The command LED

will ﬂash once again.

Press and hold the button

on the remote control. Release the button when

the garage door opener

lights blink or two clicks

are heard.

“click”

WARNING: This product can expose you to chemicals including lead, which are known

to the State of California to cause cancer or birth defects or other reproductive harm. For

more information go to www.P65Warnings.ca.gov.

REPLACEMENT PARTS

3V CR2032 Lithium battery ...................................................10A20

Visor Clip ................................................................29B137

ONE YEAR LIMITED WARRANTY

The Chatmberlain Group, Inc. warrants to the first consumer purchaser of this product that it is

free from defect in materials and/or workmanship for a period of 1 year from the date of purchase.

Press and hold the button down until the door or gate

starts to move. The remote control will operate from

up to 3 car lengths away on typical installations.

Installations and conditions vary, contact an installing

dealer for more information.

HOW TO USE THE REMOTE CONTROL

NOTICE: This device complies with Part 15 of the FCC rules and Industry Canada’s license-exempt RSSs.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including interference that may cause

undesired operation. Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC rules and Industry Canada ICES standard. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

3V CR2032

Pry open the case ﬁrst

in the middle (1), then

at each side (2 and 3)

with the visor clip.

Remove the old battery.

Dispose of old batteries

properly.

Insert the replacement

battery positive side up.

Replace the battery

with only 3V CR2032

coin cell batteries.

Replace the cover.

THE REMOTE CONTROL BATTERY

The lithium battery should produce power for up to 5 years. If the battery is low, the remote control's LED will

not flash when the button is pressed. To replace battery: To prevent possible SERIOUS INJURY or DEATH:

• NEVER allow small children near batteries.

•If battery is swallowed, immediately notify doctor.

To reduce risk of fire, explosion or chemical burn:

• Replace ONLY with 3V CR2032 coin batteries.

•DO NOT recharge, disassemble, heat above 212° F (100° C) or incinerate.

www.chamberlain.com

support.chamberlaingroup.com

114A5256 All Rights Reserve

Inhaltsverzeichnis

Andere Chamberlain Fernbedienung Handbücher

Chamberlain

Chamberlain 972LM Bedienungsanleitung

Chamberlain

Chamberlain PASSPORT CPT4 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Security+ 971LM Bedienungsanleitung

Chamberlain

Chamberlain PPLV1 Bedienungsanleitung

Chamberlain

Chamberlain KLIK3C-BK2 Bedienungsanleitung

Chamberlain

Chamberlain 4330EML Bedienungsanleitung

Chamberlain

Chamberlain 972LM Security? Bedienungsanleitung

Chamberlain

Chamberlain 54332EML Bedienungsanleitung

Chamberlain

Chamberlain 33LMC Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 371LM Bedienungsanleitung

Chamberlain

Chamberlain 375LM Bedienungsanleitung

Chamberlain

Chamberlain 811LMX Bedienungsanleitung

Chamberlain

Chamberlain MC100 Bedienungsanleitung

Chamberlain

Chamberlain 972MOM Moore-o-Matic Bedienungsanleitung

Chamberlain

Chamberlain ARQ TM100 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Security+ 973-315LM Bedienungsanleitung

Chamberlain

Chamberlain SECURITY+ 535LM Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional 84LM Bedienungsanleitung

Chamberlain

Chamberlain 361LM Bedienungsanleitung

Chamberlain

Chamberlain CPTX Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Security+ 971LM Bedienungsanleitung

Chamberlain

Chamberlain Security? 971LM Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Security+ 327LM Bedienungsanleitung

Chamberlain

Chamberlain 300MC Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung