Chamberlain MC100C Bedienungsanleitung

To prevent possible SERIOUS INJURY or DEATH from a moving gate or door:

• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control

transmitters.

• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.

• ALWAYS keep gate or door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.

Universal Mini Remote Control

Read instructions thoroughly BEFORE beginning.

If using the Universal Mini Remote Control with residential door openers, the remote control must be used only

with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are

always located on or near the bottom of the door track.

STOP

MODELS MC100,

MC100C, MC100-P2

AND MC100C-P2

TABLE OF CONTENTS

GETTING STARTED ........................................................................... 2

LOCATE THE PROGRAM/LEARN BUTTON......................................3-7

Chamberlain®products................................................................ 3

LiftMaster®products.................................................................... 4

Overhead Door®products ............................................................ 4

Genie®products............................................................................ 5

Linear®products........................................................................... 6

Wayne Dalton®products.............................................................. 6

Stanley®products......................................................................... 7

GARAGE DOOR OPENERS ..............................................................8-9

Programming to a garage door opener with a

Program/LEARN button ................................................................ 8

Programming to a Genie®Intellicode®2

garage door opener...................................................................... 9

COMMERCIAL DOOR OPERATORS ................................................. 10

Programming to a commercial door operator

with a Program/LEARN button................................................... 10

GATE OPERATORS.......................................................................... 11

Program to a gate operator

with a Program/LEARN button................................................... 11

EXTERNAL RECEIVERS................................................................... 12

Programming to an external receiver

with a Program/LEARN button................................................... 12

MYQ LIGHT CONTROLS .................................................................. 13

NEED HELP? ................................................................................... 14

BATTERY ........................................................................................ 15

WARNING: This product can expose you to chemicals including lead, which are known to the State of California to

cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

GETTING STARTED

The Universal Mini Remote Control can be programmed to activate up to two products, such as a garage door opener, MyQ®light

controls, gate operator, or commercial door operator. Each button on the remote control works independently of the other and must be

programmed separately. The images throughout this manual are for reference only and your product may look different.

Bottom Button

Top Button

Garage Door Opener Commercial Door OperatorGate Operator

LED

Key Ring Holder

You will need to locate the Program/LEARN button on your product before you start programming.

GARAGE DOOR OPENERS

The Program/LEARN button is typically located on the back or side panel

of your garage door opener. Newer garage door openers may have a

Program/Learn button located on the door control. Your Program/LEARN

button may have a different name (SMART button, SET button, etc.). For

help locating your Program/LEARN button refer to the Table of Contents

in this manual or contact your garage door opener manufacturer.

COMMERCIAL DOOR OPERATORS

The Program/LEARN button is typically located on the logic board of your

operator. Your Program/LEARN button may have a different name

(RADIO button, XMITTER button, etc.). For help locating your Program/

LEARN button contact your door operator manufacturer.

GATE OPERATORS

The Program/LEARN button is typically located on the control board of

your operator. Your Program/LEARN button may have a different name

(RADIO button, XMITTER button, etc.). For help locating your Program/

LEARN button contact your gate operator manufacturer.

EXTERNAL RECEIVER

Some products do not

have a Program/LEARN

button. In this case, the

Program/LEARN button

will be located in an

external receiver. The

receiver will be located on

the product or mounted

nearby. Follow the

programming instructions

for an external receiver.

LOCATE THE PROGRAM/LEARN BUTTON

CHAMBERLAIN PRODUCTS

LOCATE THE PROGRAM/LEARN BUTTON

OVERHEAD DOOR PRODUCTS

LIFTMASTER PRODUCTS

Yellow Learn

Button

Purple Learn

Button

Orange Learn

Button

Green Learn

Button

Learn Code

Button

LOCATE THE PROGRAM/LEARN BUTTON

Learn Code

Button

Program Set Button

GENIE PRODUCTS

LOCATE THE PROGRAM/LEARN BUTTON

LINEAR PRODUCTS

Learn

Button

Learn

Button

Program SW

Button

WAYNE-DALTON PRODUCTS

LOCATE THE LEARN BUTTON

STANLEY PRODUCTS

Learn Button

GARAGE DOOR OPENERS

Programming to a Garage Door Opener with a Program/LEARN Button

The Program/LEARN button is typically located on the back or side panel of the garage door opener or an external receiver. For help

locating your Program/LEARN button refer to the Help section in this manual or contact your garage door opener manufacturer.

The Mini Remote Control is pre-programmed to work with a Chamberlain garage door opener with a yellow learn button. Press and

release the yellow learn button, then press and hold the button on the remote control you would like to use. If programming is not

successful, proceed through the steps below.

If you have a Genie®Intellicode®2 garage door opener go to the next page. If you have an external receiver, see External Receivers

page 12.

The images throughout this manual are for reference only and your product may look different.

Bottom Button

1Start with your garage door closed. 2Press and hold bottom button on the remote control until

the blue LED stays solid (approximately 15 seconds) then

release the button.

3Press and release the Program/LEARN button on your

garage door opener. or 2 times on your door control.

4On the remote control, press and release the button that

you would like to program twice. The blue LED will blink

and the remote control will begin sending the

preprogrammed codes to the garage door opener.

Transmission can take up to 60 seconds.

5 6

When the garage door begins to open, immediately press

and release either of the buttons on the remote control to

confirm the code and exit programming.

LED

Test the remote control by pressing the button you

programmed in step 4. If the garage door opener does not

activate, repeat the programming steps.

IMPORTANT: The remote will activate your garage door during

programming. Ensure garage door is clear of ALL obstructions.

LED

Programming to a Genie®Intellicode®2 Garage Door Opener

Before starting, you MUST have an existing Genie®Intellicode®2 remote control programmed to the garage door opener. For help

programming a Genie Intellicode 2 remote control to your Genie operator, see your Genie owner’s manual.

The images throughout this manual are for reference only and your product may look different.

GARAGE DOOR OPENERS (continued)

1 2

On the garage door opener, press and hold the

Program/Set button until both the long and short LED’s

light up BLUE.

Press and release the Program/Set button and the long

LED will flash PURPLE.

On the Genie®remote control, press and release the

button that is already programmed to the garage door

opener. Both LED’s will flash PURPLE.

Bottom Button

Start with your garage door closed. Press and hold bottom button on the remote control until

the blue LED stays solid (approximately 15 seconds) then

release the button.

On the remote control, press and release the button that

you would like to program 3 times. The blue LED will blink

for up to 60 seconds.

Wait for the garage door to open, then press and release

either of the buttons on the remote to complete

programming.

LED

Test the remote control by pressing the button you

programmed in step 6. If the garage door opener does not

activate, repeat the programming steps.

IMPORTANT: The remote will activate your garage door during

programming. Ensure door is clear of ALL obstructions.

LED

COMMERCIAL DOOR OPERATORS

Programming to a Commercial Door Operator with a Program/LEARN Button

The Program/LEARN button is typically located on the logic board of the operator or an external receiver. For help locating your

Program/LEARN button contact your commercial door operator manufacturer.

The Mini Remote Control comes pre-programmed to work with a Chamberlain branded Commercial Door Operator with a yellow learn

button. Press and release the yellow learn button, then press and hold the button on the remote control you would like to use. If

programming is not successful, proceed through the steps below.

If you have an external receiver, proceed to the External Receiver programming page. See the Table of Contents for page location. The images throughout this manual are

for reference only and your product may look different.

Program/LEARN

Button*

Program LED

Program/LEARN

Button*

* Depending on your product, the Program/LEARN button may have a different

name (use the button for programming remote controls).

Bottom Button

1Start with your commercial door closed. 2Press and hold bottom button on the remote control until

the blue LED stays solid (approximately 15 seconds) then

release the button.

3Press and release the Program/LEARN button* on your

commercial door operator. The program LED will

illuminate.

Wait for the program LED on the commercial door

operator to blink, then press and release the Program/

LEARN button to exit program mode.

4On the remote control, press and release the button that

you would like to program twice. The blue LED will blink

for up to 60 seconds.

5 6 Wait for the commercial door to open, then press and

release either of the buttons on the remote.

LED

Test the remote control by pressing the button you

programmed in step 4. If the commercial door operator

does not activate, repeat the programming steps.

IMPORTANT: The remote will

activate your commercial door

during programming. Ensure

door is clear of ALL

obstructions.

LED

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chamberlain Fernbedienung Handbücher

Chamberlain

Chamberlain 54332EML Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 973LM Bedienungsanleitung

Chamberlain

Chamberlain 953EV Bedienungsanleitung

Chamberlain

Chamberlain 300MC Bedienungsanleitung

Chamberlain

Chamberlain PASSPORT CPT4 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Security+ 370LM Bedienungsanleitung

Chamberlain

Chamberlain 950ESTD-P2 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 371LM Bedienungsanleitung

Chamberlain

Chamberlain TriCode Systems Bedienungsanleitung

Chamberlain

Chamberlain KLIK3U-BK Bedienungsanleitung

Chamberlain

Chamberlain Security+ 950C Bedienungsanleitung

Chamberlain

Chamberlain 375LM Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 535LM Security+ Bedienungsanleitung

Chamberlain

Chamberlain Passport CPT series Bedienungsanleitung

Chamberlain

Chamberlain KLIK5U-WP Bedienungsanleitung

Chamberlain

Chamberlain Passport PPV3 Bedienungsanleitung

Chamberlain

Chamberlain 412HMC Bedienungsanleitung

Chamberlain

Chamberlain CPT4 Bedienungsanleitung

Chamberlain

Chamberlain 361LM Bedienungsanleitung

Chamberlain

Chamberlain Security? 971LM Bedienungsanleitung

Chamberlain

Chamberlain 811LMX Bedienungsanleitung

Chamberlain

Chamberlain 33LMC Bedienungsanleitung

Chamberlain

Chamberlain TX4REV-F Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Security+ 970LM Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung