Chamberlain TriCode Systems Bedienungsanleitung

TriCode LiftMaster Four Button Garage Door Opener Remote Control

Transmitter Coding Instructions

TC4 Four Channel Transmitter Coding Instructions

This device complies with FCC Rules Part 15 and IC Canada Rules and Regulations.

Operation is subject to the following two conditions: (1) This device may not cause harmful

interference and (2) this device must accept any interference received, including

interference that my cause undesired operation. F.C.C. rules prohibit adjustments to or

modification of receiver and/or remote control transmitter circuitry except for changing the

code setting and replacing remote control transmitter battery. THERE ARE NO OTHER

SERVICEABLE PARTS.

CAUTION

ACTIVATE THE TRANSMITTER ONLY WHEN THE DOOR/GATE IS IN FULL VIEW,

FREE OF OBSTRUCTION AND PROPERLY ADJUSTED. NO ONE SHOULD ENTER OR

LEAVE THE DOOR/GATE WHILE IN MOTION. DO NOT ALLOW CHILDREN TO

OPERATE THE REMOTE(S) OR THE DOOR/GATE CONTROL BUTTONS. DO NOT

ALLOW CHILDREN TO PLAY NEAR THE DOOR/GATE.

The TriCode™ digital TC4 transmitter is a four-channel wireless radio control designed for

use with automatic garage/gate operators and access control systems. All TriCode™

products can be used with Linear/Delta 3™, Stanley™ and Multi-Code™ receivers. Two

configuration switches allow the four buttons to be configured to interface with two different

receiver types in the same transmitter. The TriCode™ radio format provides a potential of

2048 different digital codes. Two 10-posistion DIP switches, each capable of 1024 different

digital codes provide these codes. For Delta-3™ products, 512 (256x2) different digitals

codes are available.

SWITCH SETTINGS

CAUTION: To avoid possibility of duplicating codes in adjacent systems, all

transmitters should be recoded prior to operation. Unless using the maximum

number of codes four codes should not be used:

All DIP Switches ON

All DIP Switches Off

DIP Switches alternating ON/OFF

DIP Switches alternating OFF/ON

STEP 1: LOCATE SWITCHES AND CONNECT BATTERY

Locate the DIP switches, configuration switches and battery by sliding down access cover on

front of the transmitter case. DIP switches are numbered 1 through 10. The configuration

switches are located to the right of the DIP switches. The battery is located below the

switches. Connect the battery connector to the 9V battery before programming transmitter

STEP 2: SET TRANSMITTER CONFIGURATION SWITCH(S)

The TriCode™ Transmitter is factory set to Linear/Delta-3™ position. Using a pointed object

set transmitter configuration switches to desired setting..

STEP 3: SET TRANSMITTER DIP SWITCH(S)

The TriCode™ Transmitter DIP switch(s) are factory set, CH1 OFF (1-10) and CH2 ON (1-

10).

Using a pointed object set transmitter DIP switches to desired setting. For Linear/Delta-3™

compatibility, set codes on switches 1 through 8. Switches 9 and 10 are not used for

Linear/Delta-3™ products.

Note: Switches in receiver must match the switches in all transmitters used to

operate the receiver. Some older radios use toggle switches and it may be difficult

to determine 'ON' & 'OFF'. If so, try reverse settings on the TriCode™.

STEP 4: RECODE RECEIVER CODES

Once the transmitter codes have been set, verify the receiver codes are set to the following

settings:

Linear/Delta-3™ Receiver Type Detail

When the TC4 is set to the Linear/Delta-3™ transmitter type, set the receiver DIP switches

as follows.

Receiver 1 - Set switch 1-8 to match switch 1, activates from Button 1.

Receiver 2 - Set switches 1 and 2 OFF, match switches 3-8 on switch 2, activates from

Button 2.

Receiver 3 - Set switch 1 ON, switch 2 OFF, match switches 3-8 on switch 2, activates from

Button 3.

Receiver 4 - Set switch 1 Off, switch 2 ON, match switches 3-8 on switch 2, activates from

Button 4.

Multi-Code™ Receiver Type Detail

When the TC4 is set to the Multi-Code™ transmitter type, set the receiver DIP switches as

follows.

Receiver 1 - Set switch 10 OFF, match switches 1-9 on switch 1, activates from Button 1.

Receiver 2 - Set switch 10 ON, match switches 1-9 on switch 1, activates from Button 2.

Receiver 3 - Set switch 10 OFF. match switches 1-9 on switch 2, activates from Button 3.

Receiver 4 - Set switch 10 ON, match switches 1-9 on switch 2, activates from Button 4.

Stanley™ Radio Receiver Type Detail

When the TC4 is set to the Stanley™ radio transmitter type, set the DIP switches as follows.

Receiver 1 - Set switch 10 OFF, match switches 1-9 on switch 1, activates from Button 1.

Receiver 2 - Set switch 10 ON, match switches 1-9 on switch 1, activates from Button 2.

Receiver 3 - Set switch 10 OFF, match switches 1-9 on switch 2, activates from Button 3.

Receiver 4 - Set the switch 10 ON, match switches 1-9 on code switch 2, activates from

Button 4.

NOTE: The DIP switches in the receiver must match the DIP switches in all transmitters

used to operate the receiver.

STEP 5: TEST THE EQUIPMENT

If not already installed, connect the receivers to the operators as described in their

installation instructions. Be sure the door/gate is clear of people and obstructions.

Activated each transmitter button and verify that each receiver triggers its operator.

Battery Replacement: The 9 volt battery should last 12 to 18 months of normal use. The

red LED on the face of the transmitter will light dimly or not at all when the battery needs

replacing. The battery is located under the access cover.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chamberlain Fernbedienung Handbücher

Chamberlain

Chamberlain 972LM Bedienungsanleitung

Chamberlain

Chamberlain MC100C Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Security+ 973TB Bedienungsanleitung

Chamberlain

Chamberlain KLIK3U-BK2 Bedienungsanleitung

Chamberlain

Chamberlain 883LM Bedienungsanleitung

Chamberlain

Chamberlain 953EV Bedienungsanleitung

Chamberlain

Chamberlain 374UT Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 81LM Bedienungsanleitung

Chamberlain

Chamberlain 891LM Bedienungsanleitung

Chamberlain

Chamberlain Security+ 956-315CB Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster 94330E Bedienungsanleitung

Chamberlain

Chamberlain 850 Series Bedienungsanleitung

Chamberlain

Chamberlain LIFTMASTER 374LM Bedienungsanleitung

Chamberlain

Chamberlain 300MC Bedienungsanleitung

Chamberlain

Chamberlain KLIK3C-BL Bedienungsanleitung

Chamberlain

Chamberlain Power Drive Whisper Drive Security+ 953D Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional Security+ 974-315LM Bedienungsanleitung

Chamberlain

Chamberlain CPTX Bedienungsanleitung

Chamberlain

Chamberlain 970 Series Bedienungsanleitung

Chamberlain

Chamberlain CPT4 Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Professional 83LM Bedienungsanleitung

Chamberlain

Chamberlain 890MAX Bedienungsanleitung

Chamberlain

Chamberlain Security+ 953-315CB Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster Security+ 971LM Bedienungsanleitung

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung