Chamberlain LiftMaster 835LM Gebrauchsanweisung

The Perimeter Alert uses a Passive Infra-Red (PIR) Motion Sensor to detect movement of people and vehicles, while allowing small

animals to pass through undetected. The Base Station is powered by the AC adapter and the 4 AA batteries supply power in case of a

power outage.

NOTE: The Base Station is intended for indoor use only.

Model 835LM

PERIMETER ALERT

Base Station Passive Infra-Red (PIR)

Motion Sensor

Swivel Bushing

Rubber Pads

Batteries: If the AC adapter is not connected, the

AA batteries in the Base Station should last up to one week.

If the Base Station batteries are low, the Base Station will

beep every 30 minutes. The AA batteries in the PIR Motion

Sensor will last up to 2 years depending on use (lithium

batteries are recommended for colder environments). If

the PIR Motion Sensor batteries are low, the Base Station

will beep every 30 minutes until the batteries are replaced.

The PIR Motion Sensor will continue to operate with a

low battery, however the light will not illuminate. For peak

performance, inspect batteries annually and replace as

needed.

Programming Additional PIR Motion Sensors: The Base

Station can learn the code of up to 7 additional PIR Motion

Sensors, responding with unique buzzes. To program

additional PIR Motion Sensors see Step 4.

To order additional PIR Motion Sensors call

1-800-528-9131.

Clear Memory: Press and hold the Learn Button on the Base

Station until 3 beeps are heard.

On/Off: To turn the Base Station on and off, hold down the

power button until you hear the on/off tone.

Volume: The Base Station is equipped with adjustable

volume controls. The lowest volume setting is the mute

feature.

Carton Inventory

Antenna

On/Off Button

Volume

BASE STATION

Operation & Features

Overview

Mounting Plate AC AdapterSun/Rain Shield

Antenna

OFF

SWITCH SETTINGS

Switch #1

Switch #2

Learn

Button

OFF Low Sensitivity

ON High Sensitivity (Default)

OFF 15 Feet Detection Range

ON 30 Feet Detection Range

(Default)

NOTE: To avoid unwanted detection of small animals move

Switch #2 to OFF.

Assembly & Programming

Attach PIR Motion Sensor box

to mounting plate with large

silver screw. Tighten screw

until PIR Motion Sensor stays

in place when repositioned.

Install 4 AA Alkaline

batteries. (Lithium batteries

recommended for colder

environments.)

LED light will ﬂash.

Plug in the Base Station.

Adhere rubber pads to the

bottom of the base.

4 AA batteries are optional in

case of a power failure. OPTIONAL

AC Adapter Input

AEnsure Base Station and PIR

Motion Sensor are in close

proximity to each other.

Press and release Learn

Button on Base Station.

Buzzer will sound.

BWithin 60 seconds, press the

Learn Button on the inside of

the PIR Motion Sensor. LED

light will illuminate and Base

Station will buzz.

Learn Button

PIR Motion Sensor

SWITCH #1:

SWITCH #2:

4Learn Button

Insert battery pack facing away

from circuit board and fasten

cover with the smallest screws

(provided).

NOTE: Ensure the batteries do

not touch the circuit board and

the antenna and battery wires

are not pinched.

PIR MOTION SENSOR INSTALLATION

Mount PIR Motion Sensor

horizontally on solid surface

a few feet off the ground and

within 1/2 mile of Base Station

(rotate sensor to access screw

holes). Unit should be able to

swivel as needed.

Attach sun/rain shield.

NOTE: Keep PIR Motion

Sensor antenna away from

metal objects. Do not mount

PIR Motion Sensor in direct

sunlight, near moving tree

branches, or in the path of a

sprinkler system.

3' - 5'

10' - 20'

Vehicle Alert Installation: For cars, the best mounting

position is about 4 feet high, between 10-20 feet back, and

angled to see the back of car after passing the sensor.

Test PIR Motion Sensor by

waving hand in front of sensor.

LED light should ﬂash and

the Base Station will buzz X

number of times indicating

which sensor has been

activated.

Troubleshooting

The PIR Motion Sensor lights up, but the Base Station does

not respond.

The PIR Motion Sensor must be programmed to Base Station

(See Step 4). Ensure Base Station is on and the volume is

turned up.

PIR Motion Sensor is detecting motion only part of the time.

Ensure the PIR Motion Sensor is set to the High Sensitivity

setting (See Step 2). To detect cars, it is best to mount PIR

Motion Sensor at height of car’s motor and have it between ten

and twenty feet from the road. Swivel sensor as needed.

The Alert is giving false alarms.

Check for moving tree branches or insects in sensor window.

PIR Motion Sensor can also be triggered by light shining

directly in sensor window, such as reﬂected sunlight, or motion

in front of a light source.

It is possible that condensation has built up on the sensor. Wipe

condensation from PIR Motion Sensor with cotton swab. Let it

sit inside for a few hours, open to the air, without the batteries

and it should correct itself.

Check Sensor Switches on PIR Motion Sensor. See Switch

Settings.

Base Station beeps every 30 minutes.

The batteries in the Base Station or the PIR Motion Sensor(s)

are low. Replace the 4 AA batteries. Check the PIR Motion

Sensor(s), if the LED illuminates on all of the PIR Motion

Sensors, change the batteries in the Base Station.

The Alert is not getting expected transmission range.

Keep both antennas vertical and keep PIR Motion Sensor

antenna away from trees and metal objects. Ensure Base Station

is in clearest possible sight of the PIR Motion Sensor. The less

objects between the devices, the longer the range.

NOTE: The manufacturer is not responsible for any radio or

TV interference caused by unauthorized modiﬁcations to this

equipment. Changes or modiﬁcations not expressly approved

by the manufacturer could void the user’s authority to operate

the equipment.

FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:

1-800-528-9131

www.liftmaster.com

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this

receiver and/or transmitter are prohibited, except for changing the code setting or replacing the

battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

Inhaltsverzeichnis

Andere Chamberlain Sicherheitssystem Handbücher

Chamberlain

Chamberlain 976LMC Security+ Bedienungsanleitung

Chamberlain

Chamberlain CWA2000 Bedienungsanleitung

Chamberlain

Chamberlain LC-36A Montage- und Bedienungsanleitung

Chamberlain

Chamberlain WIRELESS ALERT CWV1000 Bedienungsanleitung

Chamberlain

Chamberlain LA412DC Bedienungsanleitung

Chamberlain

Chamberlain 8747AML Bedienungsanleitung

Chamberlain

Chamberlain RWV400R Bedienungsanleitung

Chamberlain

Chamberlain CWA2000C Bedienungsanleitung

Chamberlain

Chamberlain CWA2000 Bedienungsanleitung

Chamberlain

Chamberlain Reporter RWA-300R Bedienungsanleitung

Chamberlain

Chamberlain RWA310R Bedienungsanleitung

Chamberlain

Chamberlain K29-32410 Bedienungsanleitung

Chamberlain

Chamberlain K74-18655 Bedienungsanleitung

Chamberlain

Chamberlain Reporter RWA-300R Bedienungsanleitung

Chamberlain

Chamberlain Reporter RWA-300R Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung