Chamberlain SMART GARAGE MYQ-G0301 Bedienungsanleitung

Smart Garage™Hub

Manual

Smart Garage™Hub

Manual

MYQ-G0301 • MYQ-G0301C

MYQ-G0301-D • MYQ-G0301LA

For iOS devices

- 2 -

Read instructions thoroughly BEFORE beginning.

If using this product with residential door openers, this product must be used only with door openers

manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located

on or near the bottom of the door track.

Before you start, you MUST have…

• A router with 2.4GHz Wi-Fi® frequency

• Router congured with 802.11 B/G/N

• Router within 50 ft. of MyQ Smart Garage Hub

• Mobile phone connected to your home Wi-Fi network

• Home Wi-Fi network password

• Latest version of MyQ App

NOTE: If using iOS 10, see

Alternative Installation Method on page 16.

• Compatible garage door opener (see Compatible Garage Door Openers on page 20)

• Locate program or learn button on the garage door opener

See Appendix on page 21 for a more detailed list of program or learn button locations.

To reduce the risk of SEVERE INJURY to persons:

• DO NOT enable the MyQ® Smart Garage™ Hub if operating either one-piece or swinging doors. To be enabled

ONLY on a sectional door.

Before You Start

Program Button

LED

WARNING: This product can expose you to chemicals including lead, which are known to the State of California

to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

- 3 -

Wi-Fi Hub

Door Sensor

Model MYQ-G0302

Power Adapter

Hardware for Wi-Fi Hub

(5/32" x 1-1/2" screws)

Mounting bracket

Hardware for

Door Sensor

(5/32" x 3/4" screws

)

Fastening Strips for

Door Sensor

Warning Label

(not shown)

Blue LED

Red

LED

Test

Button

Green LED

Yellow LED

What’s in the Box

Tools Needed: Drill, 5/32" Drill Bit, Screwdriver, Ladder

MyQ Smart Garage Hub

Blue LED

Light

Door Sensor

Fastening Strips for

Door Sensor

Hardware for

Door Sensor

(5/32” x 3/4” screws)

Warning Label

(not shown)

Hardware for

MyQ Smart Garage Hub

(5/32” x 1-1/2” screws)

Mounting bracket

Power Adapter

Test Button

Green LED

Yellow LED

Before You Start

- 4 -

NOTE: If using iOS 10, see Alternative Installation Method on page 16.

Step 1: Check your Wi-Fi signal

Make sure your mobile phone is connected to your Wi-Fi network. Hold the mobile phone near where you plan to

install the MyQ Smart Garage Hub.

If you see:

Wi-Fi signal is strong. You’re all set! Proceed to next step.

Wi-Fi signal is weak. The MyQ Smart Garage Hub may not connect to your Wi-Fi network. If it doesn’t

connect, try one of the options below.

No Wi-Fi signal. Try one of the following options:

• Move your router closer to the garage to minimize interference from walls and other objects.

• Buy a Wi-Fi range extender.

To watch a video on How to test your Wi-Fi Signal Strength before setting up your MyQ® product,

go to youtu.be/_Ow1wVF-7AU

(mounting area)

MyQ Smart Garage Hub

mounting area

Wireless Setup and Installation

- 5 -

Step 2: Install door sensor

1. Remove the pull tab from the door sensor to activate the battery.

2. Test the door sensor by pushing the test button and conrming the LED on the door sensor blinks.

If the LED on the door sensor does not blink, see Troubleshooting on page 16.

3. Install the door sensor on the top panel of the garage door using the fastening strips or provided hardware.

IMPORTANT: Door sensor MUST be installed to read “myQ” lettering right-side up.

Step 3: Download the MyQ App

If you already have the MyQ App, verify you have the latest version. To conrm you have the

latest version of the app, go to the App StoreSM and search for the Chamberlain MyQ App.

If you see Update, tap Update.

Wireless Setup and Installation

Door Sensor

LED

“TOP” MUST

always face UP

Test

Button Fastening

Strips

Screws

CR2450 Battery

Press

- 6 -

If you have already registered a MyQ account, skip this step and login.

Step 4: Create and Register your MyQ Account

1. Open the MyQ App and tap Sign Up.

2. Enter rst name, last name, valid email address, and password

(twice), country, and zip code.

NOTES:

• Check email address for errors.

• Use a valid email address you can access.

• If the email address you are attempting to use is already in the

MyQ system, you will receive an error message. If necessary,

tap Forgot Password to retrieve the password for that email

and login. For more information, see Troubleshooting on page

16.

3. Tap Submit (top right-hand corner). An email will be sent to the

email address you provided.

5. Open the email from Chamberlain support and tap the link to

complete your registration. The MyQ App will open, verifying

registration of email address was successful. NOTE: If you didn’t

receive an email, check the Junk or Spam folder.

6. Tap OK.

7. Enter your email address and password and tap Login.

Congratulations! Registration of your account is now complete.

Wireless Setup and Installation

- 7 -

Blue LED blinks

Step 5: Power up the MyQ Smart Garage Hub

Find a convenient location and plug in the MyQ Smart

Garage Hub. Wait for the blue LED to blink.

If blue LED is not blinking:

Unplug and plug back in.

If the blue LED still does not blink, reset to factory

default:

1. Press and hold the Settings button until the

blue LED blinks (about 10 seconds) then release.

2. Press and hold Settings button again until the

MyQ Smart Garage Hub beeps.

IMPORTANT NOTE: Resetting the MyQ Smart Garage

Hub to factory default erases the Wi-Fi settings, erases

door sensors, and removes the MyQ Smart Garage Hub

from the currently paired MyQ account.

Step 6: Login to MyQ App

Enter the email and password you used to register your account and

tap Login.

TIP: Select Remember Me if you want the MyQ App to remember

your email address and password. You can change the security

settings within the MyQ App by tapping the menu bar in top-left

corner and then your name on bottom-left to access settings.

Blue LED blinks

MyQ Smart Garage Hub

Wireless Setup and Installation

Settings Button

- 8 -

Wireless Setup and Installation

In the MyQ App:

1. Tap Get Started or tap “+”.

3. Enter your MyQ serial number (found on the back of

the MyQ Smart Garage Hub) and tap Next.

2. Tap Add New.

4. Tap Join to connect to the network.

NOTE: If you don’t see this screen, see Alternative

Installation Method on page 16.

Step 7: Connect the Smart Garage Hub to your Wi-Fi Network

- 9 -

Step 7: Connect the Smart Garage Hub to your Wi-Fi Network continued

6. Enter your home Wi-Fi network password and tap

Connect.

Wireless Setup and Installation

8. Enter a name for your MyQ Smart Garage Hub and

tap Next.

7. Wait for the solid green LED on your MyQ Smart

Garage Hub. This can take up to 2 minutes.

Result: LED is solid green. NOTE: If the LED is not

solid green, see Troubleshooting on page 16.

5. Select your home Wi-Fi network from the list.

- 10 -

Wireless Setup and Installation

Step 8: Add New Device

Now that your MyQ Smart Garage Hub is connected to your home Wi-Fi network, the next steps will guide you through

the process of pairing your garage door opener to your MyQ Smart Garage hub.

TIP: A device is any MyQ accessory that can be paired with your MyQ Smart Garage hub for monitoring and control. This

includes MyQ Lighting accessories and an add-on door sensor that expands your MyQ functionality to a second garage door.

The following steps are to add a garage door opener.

1. Select Garage Door Opener.

3. Locate test button on door sensor and tap Next.

Door Sensor

Red

LED

Test

Button

MyQ Smart Garage Hub

Light

2. Conrm your door sensor is mounted and tap Next.

4. Press and release the test button on the door sensor.

The MyQ Smart Garage Hub will beep and the light

will ash.

Andere Handbücher für SMART GARAGE MYQ-G0301

Inhaltsverzeichnis

Andere Chamberlain Schalten Handbücher

Chamberlain

Chamberlain SMART GARAGE MYQ-G0301 Bedienungsanleitung

Chamberlain

Chamberlain K90-9210M2L5 Bedienungsanleitung

Chamberlain

Chamberlain myQ CAPAC Bedienungsanleitung

Chamberlain

Chamberlain LiftMaster CSL24V Montage- und Bedienungsanleitung

Chamberlain

Chamberlain RZ94-05 Bedienungsanleitung

Chamberlain

Chamberlain WSLCEV Bedienungsanleitung

Chamberlain

Chamberlain RZ94-05 Bedienungsanleitung

Chamberlain

Chamberlain 760CB Bedienungsanleitung

Chamberlain

Chamberlain SMART GARAGE MYQ-G0301 Bedienungsanleitung

Chamberlain

Chamberlain SMART GARAGE MYQ-G0301 Bedienungsanleitung

Chamberlain

Chamberlain K71-33445 Bedienungsanleitung

Chamberlain

Chamberlain 823LM Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch