Chamberlain Elite DC2000 Bedienungsanleitung
13
2
76
5
4
Strike Open
Push Button
Strike Open
Push Button
24 Volts DC
24 Volts DC
Fire Dept
Key Switch
Fire Dept
Key Switch
M/S Link
M/S Link
Class 2
Supply
Class 2
Supply
Center
Loop
Center
Loop
Safety
Loop
Safety
Loop
Radio
Receiver
Radio
Receiver
Exit
Loop
Exit
Loop
GG BB AA
++
OmniControl Surge Suppressor
P/N Q410
Patent Pending
P/N Q410
Patent Pending
CENTER SAFETY EXIT
CENTER SAFETY EXIT
FIRE
DEPT.
13
STRIKE
OPEN
RADIO
RECEIVER
TIMER
SYSTEM ON
EXIT
LOOP
ALARM
SENSOR
REVERSE
SENSOR
OPEN
STOPCLOSE
SAFETY
LOOP
CENTER
LOOP
GATE
LOCKED
60 POWER
OVERLOAD
OFF
W4
OPEN LEFT
DC-BACKUP
ALARM
SENSOR
OPEN RIGHT
3
SENSORS
RESET
MOTOR
13
13
COMMAND
PROCESSED
ON
GB
MS LINK
A
MADE IN USA
OFF
ON
CHASSIS
GROUND
12 1311
CAUTION
Black 120 Vac
WhiteNeutral
GreenGround
OPEN
STOP
LOSE
POWER
OVERLOAD
MADE IN USA
CLO
Push and “Hold” a Button to operate
“Optional Manual One-Button”
“Optional Three-Button”
Socket
“Optional Edge Sensor”
“Optional Radio Receivers”
“Optional Key Switch”
OmniControl™ Board
Sensor Connection
Push and “Hold” to Open
Push again and “Hold” to Close
Turn and “Hold” to Open
Turn again and “Hold” to Close
POWER
OVERLOAD
DC-BACKUP
ALARM
SENSOR
1
3
2
4 5
6
4
N.O.
N.O.
N.O.
USE ONLY 12 VDC FAILSAFE PHOTOCELL
SENSORS FOR THIS SAFETY OPTION
Failsafe Photocell: If a photocell is not
working or loses power or photo beam is
blocked, then the photocell will stop all gate
operation.
“Optional Photocell Sensor” 12 VDC
Interlock
Assembly
5
4
1
1234
Com
Com
Com
45
SAFETY OPTIONS
DC2000 Back-Up Wiring for the OmniControl™ Board with Optional Equipment
Power +12 VDC
Power Ground
Part #
AEXITP
Part #
AEXITP
Part #
A1KX
Part #
A1KX
Part #
312HM
Part #
312HM
Part #
373LM
Part #
373LM
Part #
AOMRON12VAOMRON12V
4
4
4
4
If the DC2000 is automatically opening the gate
due to a power failure, any manual command
such as “Manual One-Button”, “Three Push
Button”, “Key Switch”, “Photocell”or “Edge
Sensor”will cancel the automatic mode of the
DC2000. After such cancellation, the DC2000
will continue to operate in manual mode until
115 Vac power is restored.
If 115 Vac power is on, but the system has
an electronic malfunction, the gate can be
operated using the DC2000 system with
ANY of these devices shown.
EMERGENCY
OVERRIDE
J5
POWER
OVERLOAD
DC-BACKUP
ALARM
SENSOR
BACK
CK
-B
DC2000 Harness
Red Wire
White Wire
J5
Green and Purple wires
wrap behind board to
the limit switches
Audio Alarm
Wires
DO NOT remove existing
wires from the audio alarm or
secondary protection sensor.
“Manual” setting: The DC2000 will respond to the input devices wired to the J 20 socket.
This mode can also be used as an emergency override. If 115 Vac power is on, but the system has an electronic
malfunction, the gate can be operated using the DC2000 system with input devices wired to J 20 socket.
“Auto” setting: The DC2000 opens the gate automatically upon 115 Vac power failure and stays open. When
115 Vac power is restored, the gate operator will return to normal operation. (The gate can be closed by manual
command)
System Setup
Manual
Mode
Auto
Mode
Push and Hold to
operate gate
115 Vac Power
Failure
115 Vac Power On,
OmniControl Board™ Malfunction
115 Vac Power On,
Emergency Override
Gate automatically
opens
Turn the 115 Vac power off then
push and Hold to operate gate
Push and Hold to override
the OmniControl™ Board
Push and Hold to override
the OmniControl™ Board
Turn the 115 Vac power off then
gate opens automatically
For Technical Support
and Ordering Parts:
1-800-528-2806
OPEN CLOSE
DO NOT wire
115 Vac power
to the DC2000
DC
2
0
0
0
H
a
r
n
e
s
s
Jumper P3:
to 12 Volt
Jumper P2:
to Constant (C)
®
Button One:
Normal Gate
Operation
(OmniControl™ Board)
Button Two:
Back-Up Operation
(DC2000)
Button Three:
Optional Accessories
Push and “Hold” DC2000 Remote Button to Open
Push again and “Hold” DC2000 Remote Button to Close
6
34
Refer to Receiver
Manual for Further
Details about settings.
Button One:
Normal Gate Operation Only
(OmniControl™ Board)
Separate 12 VDC
DC2000 Radio Receiver
Interlock Assembly Wire
4
3Factory installed
Interlock Assembly
Wires to J20 Socket
Cut and
Discard Plug
To Limit Switches
Radio Receiver +
Radio Receiver -
13
11
11
12
24 VDC
Factory Installed
Radio Receiver
123
11
11
13
4
12
J 20
STEP 7
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5
STEP 6 STEP 8
SL3000UL™ & SL3000ULDM™ with Interlock AssemblyStep-by-Step DC2000 Installation
Bolt the DC2000 plate and guard to the operator chassis. Do
not tighten the bolts. Adjustment is required in Step 3.
Bolts
Plate
Bolt the DC2000 control unit to the plate.
Bolt the DC motor to the plate.
Connect the DC motor wires to the DC2000 control unit wires. Red to Red and Black to Black.
DC Motor
Remove interlock assembly from motor with 3 screws.
Replace the existing belt with the new belt provided. Make sure that the pulleys are aligned.
Pull down the DC2000 Plate to tighten the belt tension. Tighten the plate bolts to secure the plate.
Reattach interlock assembly.
SL3000UL™
Use 4L 370 Belt
SL3000ULDM™
Use 4L 400 Belt
Do not over tighten belt
W4
OFF
ON
J5
POWER
OVERLOAD
DC-BACKUP
ALARM
SENSOR
BACK
-BACK
Connect the purple and green wires to the limit switches.
Make sure brown wire is in the “Common” connector on the limit switch.
Remove the OmniControl™ board from the electrical box.
Plug in the DC2000 harness into the DC2000 control unit.
Feed the DC2000 harness through the bottom of the electrical box.
Feed the green and purple wires to the limit box.
OFF
ON
W4
Unplug interlock wire from
OmniControl board, cut the plug
off and strip wires. Insert Red
wire in J-20 socket 3and
Black wire into socket 4of the
DC2000.
NC
1
2
3NO
COM
Brown
Red
Yellow
Orange
Purple
Green
NC 1
2
3
NO
COM
Top View of Limit Switch BoxTop View of Limit Switch Box
DC2000
Control Unit
Existing Belt
Reinstall the OmniControl™ board and make sure that the green and purple wires do not get pinched by the board.
Plug in the DC2000 harness in the DC-BackUp J5 slot on the OmniControl™ board.
Connect the red wire from the DC2000 harness into the top slot of the audio alarm plug. (DO NOT remove audio alarm wires)
Connect the white wire from the DC2000 harness into the bottom slot of the sensor plug.
Set switch for the gate
direction. (Open left or
Open right)
Select your mode of
operation for the DC2000
unit. (Automatic open or
Manual open)
Permanently wire optional
controls according to label
on control unit. (See back
page)
Adjust the sensitivity for
the reverse sensor.
Plate
Guard
CC
D
D
B
A
B
A
B
A
A
A
B
A
A
A
BB
B
C
C
B
C
A
BA
B
C
DD
A
A
B
C
DD
A
B
C
DD
C
C
D
C
B
C
STEP 6
STEP 1 STEP 2 STEP 3 STEP 4
STEP 5 STEP 7
SL3000UL™ & SL3000ULDM™Step-by-Step DC2000 Installation
Bolt the DC2000 plate and guard to the operator chassis. Do not tighten the
bolts. Adjustment is required in Step 3.
Bolts
Plate
Bolt the DC2000 control unit to the plate.
Bolt the DC motor to the plate.
Connect the DC motor wires to the DC2000 control unit wires. Red to Red and Black to Black.
DC Motor
Replace the existing belt with the new belt provided. Make sure that the pulleys are aligned.
Pull down the DC2000 Plate to tighten the belt tension. Tighten the plate bolts to secure the plate.
SL3000UL™
Use 4L 370 Belt
SL3000ULDM™
Use 4L 400 Belt
Do not over tighten belt
W4
OFF
ON
J5
POWER
OVERLOAD
DC-BACKUP
ALARM
SENSOR
BACK
CK
-B
Connect the purple and green wires to the limit switches.
Make sure brown wire is in the “Common” connector on the limit switch.
Remove the OmniControl™ board from the electrical box.
Plug in the DC2000 harness into the DC2000 control unit.
Feed the DC2000 harness through the bottom of the electrical box.
Feed the green and purple wires to the limit box.
OFF
ON
W4
NC
1
2
3NO
COM
Brown
Red
Yellow
Orange
Purple
Green
NC 1
2
3
NO
COM
Top View of Limit Switch BoxTop View of Limit Switch Box
DC2000
Control Unit
Existing Belt
Reinstall the OmniControl™ board and make sure that the green and purple wires do not get pinched by the board.
Plug in the DC2000 harness in the DC-BackUp J5 slot on the OmniControl™ board.
Connect the red wire from the DC2000 harness into the top slot of the audio alarm plug. (DO NOT remove audio alarm wires)
Connect the white wire from the DC2000 harness into the bottom slot of the sensor plug.
Set switch for the gate
direction. (Open left or
Open right)
Select your mode of
operation for the DC2000
unit. (Automatic open or
Manual open)
Permanently wire optional
controls according to label
on control unit. (See back
page)
Adjust the sensitivity for
the reverse sensor.
Plate
Guard
C
D
D
B
A
B
A
B
A
A
A
B
A
AA
B
BB
B
C
A
BA
B
C
DD
A
A
B
C
DD
A
B
C
DD
C
D
C
B
C
Interlock
Assembly
A
13
2
76
5
4
Socket 3 & 4
01-51128B
DC2000 Back-Up Installation for SL3000UL™ models
845 Larch Avenue Elmhurst, Illinois 60126
www.chamberlain.com
For Technical Support and Ordering Parts:
1-800-528-2806 © 2008 The Chamberlain Group, Inc.
All Rights Reserved
®
™
Inhaltsverzeichnis
Andere Chamberlain UPS Handbücher
Beliebte UPS Handbücher anderer Marken
Pylontech
Pylontech Victron & Pylontech US5000 Bedienungsanleitung
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung
Mecer
Mecer ME-1000-WTU Bedienungsanleitung
Mustek
Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch
Emerson
Emerson Liebert NXL series Bedienungsanleitung
MAKELSAN
MAKELSAN BOXER SERIES Bedienungsanleitung
