Channel Plus 9510HHR Bedienungsanleitung

9500 Series

714-996-4100 * 800-999-5225 * fax 714-996-4900 * www.channelplus.com

PERFORMANCE MULTI-ROOM VIDEO

Multiplex Technology, Inc. warrants this product to be free from

defects in materials and workmanship for a period of one year from

the date of purchase or MTI will repair, or at its option, replace the

defective product. To obtain warranty service, call MTI for a return

material authorization (RMA) number and return the product pre-

paid to Multiplex Technology, Inc., 3001 Enterprise Street, Brea, CA

92821, Attention: Customer Service. Please put the RMA number on

the outside of the carton.

Any implied warranty arising from the sale of the product including

implied warranties of merchantability and fitness for purpose are lim-

ited to the warranty stated above. MTI shall not be responsible for

losses or damages or expenses, whether direct, consequential or

incidental arising from the use of or the inability to use this product.

Some states do not allow limitations on how long the implied war-

ranty lasts or the exclusions or limitations or incidental or conse-

quential damages, so the above limitations and exclusions may not

apply to you. This warranty gives you specific legal rights, and you

may have other rights which may vary from state to state.

WARRANTY

Models

9510HHR B&W

9520HHR Color

9510BID B&W

9520BID Color

9510PAL B&W

Specifications: typical @ 25°C ± 5° C

9510 (B&W) 9510PAL(AUS) 9520 (Color)

lens viewing angle 78°

resolution: horizontal 525 lines 625 lines 525 lines

vertical 350 lines 350 lines 350 lines

standard lens cover: smoked

minimum light level 2 lux 2 lux 8 lux

video input format EIA CCIR NTSC

input signal 1.0 V peak-to-peak @ 75Ω

signal-to-noise ratio >45 dB

white balance automatic

electronic shutter speed automatic: 1/60 to 1/50,000 second

tuning range UHF 14 to 64 21 to 62(28 to 67) 14 to 64

CATV 65 to 125A 65 to 125A

power supply included with product

mains power 105 to 125 210 to 250 105 to 125

output of power supply 15VDC 600mA

general injector module camera module

width x height x depth 6.5” x 3.5” x 1.25” 3.25” x 3.25” x 1.5”

(16.3cm x 9cm x 3.2cm) (8.2 cm x 8.2cm x 3.8cm)

shipping weight 2 lbs (0.9 kg)

operating temperature –4°F to 131°F (–20°C to 55°C)

A excluding channels 95 through 99

The CatCam is a surveillance system that creates a new channel

to add to existing television channels. The new channel carries a

picture from the camera that is placed anywhere in the home. The

CatCam was designed to install effortlessly into existing coax home

wiring or into new construction.

Contents: Channel Injector

Camera

Power Injector

Power Supply

Coax Jumper

The CatCam is comprised of a camera and a channel injector. The

camera is designed to flush mount indoors or outdoors (under an eaves

and not directly exposed to the elements) using a deep double gang J box. The

channel injector is weather resistant and designed to mount indoors

or outdoors close to the incoming CATV or antenna feed. The sys-

tem uses the existing coax cable distribution in the house.

The CatCam was designed to work with Cat 5 wiring. Although the

system will function with quad wire, Cat 5 delivers the highest quality

picture. The Cat 5 allows the use of an automatic line length sensor

and picture compensator. Quad wire does not take advantage of

this enhancement.

Model Differences:

The model 9500HHR series is a high headroom design for CATV

and off air antenna feeds only.

The model 9500BID series is a bi-directional design for use with

CATV cable boxes that are interactive or require bi-directional com-

munications with the cable company.

The model 9510PAL is designed to modulate PAL frequencies and

use CATV or off air antenna feeds.

Installation:

First, locate the incoming CATV or antenna feed and install the

channel injector at that location.

Second, install the camera at the desired location and run Cat 5 wire

from the camera to the channel location.

Third, apply power and select an unused channel for the CatCam

picture to appear on all the televisions.

Installation: Step One

Locate the incoming CATV or antenna feed and existing splitter.

(Usually found on the side of the house, in the attic or near the electrical and phone service box)

Remove the lock screw located on the bottom of the channel

injector and slide the cover off. Use the mounting holes as shown to

affix the channel injector to the wall next to the splitter.

Disconnect the incoming CATV or antenna feed from the existing

splitter and attach it to the channel injector as shown.

Now attach the supplied coax jumper back to the existing splitter

and tighten all connections with a 7/16” wrench.

Use mounting

holes on the

bottom plate to

attach channel

injector to the

wall

Incoming CATV or

antenna coax

Out

to TVs

Incoming CATV or

antenna coax

Supplied coax

jumper goes back

to splitter

Out

to TVs

After

Before

Mount the

injector within

4” of the splitter

Mount the

injector within

4” of the splitter

Installation Step Two

The camera mounts using a deep double “J” box. Run a line of Cat 5

wire from the camera to the channel injector and connect wires as

shown.

Attach Cat 5 wire to camera following color coding.

note:

When using quad wire connect

wires only to pins 1, 2, 5 and 6.

Leave the resistor in place

at pins 3 and 4.

note:

When using Cat 5 wire

remove the default resistor

that is in pins 3 and 4 of the

camera

prepare the Cat 5 wires by

stripping 1” of outer sheath

and 1/8” of insulation

attach drip cap,

gasket and frame

insert the 6-32 screws into

frame and bottom holes of

gang box

Note: bottom of lip on drip cap

goes inside frame.You may have

to rotate drip cap 180˚

frame

gasket

drip cap

pin 1 2 3 4 5 6 7 8 Default

resistor

Green

pin 1 Red

2Black

5Yellow

Bl/W Blue Org/W Orange Gr/W Green Br/W Brown

frame

gasket

drip cap

“Hook” camera mount over the gasket and rotate into place.

Apply RTV to seal from weather.

Add top screws.

Aiming the camera Insert a 1/8” screw driver in the

steering slot below the lens.

Using the screwdriver, bend

the mount to the point camera

in the desired direction. Never

use the camera to bend the

mount. continued on page 6

Applying Power and Programming

Step Three

The 9500 series has three different methods for applying power

to the system.

Use only one method for applying power.

Method One: Apply power directly to the channel injector with the

power supply.

The green LED in the upper right corner of the injector will be lit

showing power is active.

(See power length requirements page 9)

Bend camera angle to give the best cov-

erage for the given height of camera

placement.

Attach the lens cover.

Lens cover rides on lip of frame

then rotates downward and snaps

into place.

Channel Injector wire connection:

At the channel injector, connect Cat 5 wire as shown. Follow the

color coding on the screw terminal.

Power plug

Lower right of

channel injector

power supply

blue/white

pin 1

When using only quad wire

use positions 1, 2, 5 and 6

and follow color coding.

run the Cat 5 wire

through the grommet at the

bottom of the injector

blue/white

pin 1

Method Two: Use the power injector to apply power along the Cat

5 or quad wire run. Cut the connecting wire along the run and insert

the power injector. Connect the wires using the color coding. Then

plug the power supply into the power injector.

The green LED in the upper right corner of the channel injector will

be lit showing power is active.

Method Three: Apply power directly at the camera.

power injector

pin 1

blue/white

cut Cat 5 wire

power plug

power supply

cut the power

supply cord and

strip the wires

wire with the

white stripe

connects to the

(+) terminal

power supply

Power Length Requirements

Method One

Power Length Requirements

Method Two

Power Length Requirements

Method Three

power supply with

end removed

Up to 300’ of

Cat 5 or quad wire

maximum for

the 9510 B&W.

Up to 100’ for the

9520 Color

power plug

Up to 100’ of

Cat 5 or quad

wire maximum

Up to 100’ of

Cat 5 or quad

wire maximum

Up to 300’ of

Cat 5 or quad wire

maximum for

the 9510 B&W.

Up to 100’ for the

9520 Color

How to Program

Determine which unused channel you want to view your video

source on and program the injector for that channel. There must be

one unused channel both before and after the selected channel to

avoid interference. The new channel will be combined with the exist-

ing channels and appear on all televisions.

To program: For example channel 60

1: Press the button 6 times.

2: Wait for the LED to relight.

3: Press the button 10 more times (pressing 10 times enters “0”).

The injector will now combine the camera feed on channel 60 with all other

existing channels from the incoming CATV or antenna.

To program a three digit channel: For example channel 120

1: Press the button 1 time.

2: Wait for the LED to relight.

3: Press the button 2 more times.

4: Wait for the LED to relight.

5: Press the button 10 more times.

Finding Unused Channels

CATV: Determine the highest channel number delivering a picture,

excluding 95-99. Tune the TV up one channel at a time from the last

channel with a picture until finding one channel with no trace of a

picture or interference, just snow.

Antenna: Tune the TV one channel at a time from channel 14-64.

Locate one channel that has no trace of a picture or interference,

just snow.

green LED

programming button

Upper right corner on

channel injector

Programming a New Channel

Valid channels are 14 thru 64 for UHF and 65 thru 125 for CATV

Channels 95-99 are not available. Channels 21 thru 62 are for Pal.

Channel Spacing:

Skip at least one number between the new channel and the closest

existing UHF/CATV channel.

(example 14 and 16: OK 14 and 15: Unacceptable)

Error Indication:

If an error occurs or an incorrect channel is entered, the LED will

flash quickly for one second and return to previous settings.

Cable HRC and IRC considerations:

Most cable services use IRC frequency assignments. This is the

default for the 9500. However, if the cable services uses HRC or

the TV appears to search for the “created channel”, program the

channel injector for HRC.

For HRC enter 98. Reset to IRC by entering 99.

Entries 98 and 99 are for setting HRC or IRC only. They will not

change the channel number.

With programming complete, test each TV in the system to see that it is

receiving the new channel.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Channel Plus Sicherheitssystem Handbücher

Channel Plus

Channel Plus CAT CAM 9511BID B&W Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung