Chase-durer CENTRAL COMMAND Bedienungsanleitung

ETA Cal. 251.265

CHASE-DURER

9601 Wilshire Blvd. #1118

Beverly Hills, CA 90210 USA

Tel: 800.544.4365 / 310.550.7280

Fax: 310.550.0830

E-mail: Customer-Ser[email protected]

www.chase-durer.com

CENTRAL COMMAND

ALARM CHRONOGRAPH

OPERATION MANUAL

CHASE-DURER

Table of Contents

Display and Screw Down Crown/Pushbuttons

® LCD Digital Displays

® E6B Flight Computer

® Specifications

Setting Time and Date

® Setting Date/Time and Alarm

Setting Time Zones/Leap Year

Resetting Chronograph Hands to Zero

Timing Mode • Simple Chronograph Function

Timing Mode • Split-Time or Intermediate Times Function

® Timing Mode • Lap-Time Function

E6B Flight Computer

® E6B Flight Computer

® E6B Flight Computer (Conversion Table)

DISPLAY and Screw Down Crown/Pushbuttons

MPH

C H A S E - D U R E R

8 4

CHRONOGRAPH HANDS

WATCH HANDS

12 hour counter

60 second counter

30 minute counter

*Right LCD

Minute hand

Hour hand

Second hand

Pushbutton A

Setting Crown

E6B Flight Computer

Interior Rotating Dial

E6B Interior Dial Setting Crown

E6B Stationary Dial

Screw Down Crown and Pushbuttons

NOTE - Failure to screw down Crown to resist moisture will void your warranty

Screwed

Down Setting Positions

Pushbutton B

WARNING: Crown must be locked down in position 1 at all times, use positions

2 & 3 for adjustments only. Do not operate pushbuttons under water!

1 crown in and turn clockwise until tight

to lock down.

Turn crown counterclockwise until you no longer

feel the threads gripping; crown can now be pulled

out to positions 2 & 3.

Push

LCD digital display functions are explained in detail on the following pages.

Pushbutton D

2 .Date, Time Zone, and LCD adjustment, Chronograph hands reset position

3 Stops second hand, setting minute and hour hands position.

Pushbutton C

*Left LCD Date Indicator/

1/100 second counter

LCD Digital Displays

Left LCD

Time Setting

Alarm Indicators

Chronograph Indicators

Blinking or partial displays when watch is in normal operating

mode (not setting mode) indicates a low battery condition.

Alarm Hour

Setting

Month

Alarm ON

Alarm OFF

Chronograph

Add Function

Split Time Function

Lap Time Function

Last Elapsed Time

Total Time

C H A S E - D U R E R

8 4

Right LCD

24 Hour Time

12 Hour Time

Date

Chronograph

1/100 second

Alarm Minutes

Setting

/ /

12/24 Hour Time

mode indicators

Time Mode

Alarm Mode

Date

Information Displayed on LCD Panels

Note - When the displays are flashing while watch is in setting

mode, it indicates the watch is waiting for input.

Setting Time and Date

Note - It is very important that the following steps 1 - 6 are performed in sequence when

setting the Time and Date. Failure to do so can prevent accurate display of time

and correct Alarm function!

2. Pull setting crown out to position when the small second hand reaches “60” to stop the second

hand for exact time setting. The following steps 3 - 6 will be made with the crown in this position.

Set crown in position

2 to

hour hand

adjust only the

C H A S E - D U R E R

8 4

Set crown in

position 3

the Second Hand

and adjust both hour

and minute hands

to Stop

1. Pull setting crown out to position and preset the hour hand to the correct hour with the crown.

(continued)

4. Set the hour in the left LCD to match the hour hand

setting in step 1 with button , set the minutes in the right LCD several minutes ahead of actual time

using button . Pressing or for longer than 1 second will advance the hours and minutes rapidly.

B B C

3. Make sure the setting crown is still in position

and press button to display

(time). If (date) appears, press

button once more. During the 2 seconds that

displays, press button

to change the right LCD between standard

AM/PM or 24 hour military time.

Your new Time Mode selection will appear for

2 seconds in the LCD’s, after which, it becomes

the default time mode with the hours and

minutes displayed as flashing numbers.

Setting AM/PM or 24 hour Time Mode

++/ /

+/ /

Setting the Date

5. Make sure the setting crown is still in position and press button to display (date).

If appears, press button once more. After 2 seconds, the two displays will

show flashing numbers for the month in the left LCD, and the date in the right LCD.

+/ /

Setting Date/Time and Alarm

MPH

C H A S E - D U R E R

8 4

1. Make sure the setting crown is in position .

3. Press either button or ; the LCD’s will flash indicating you are in

alarm setting mode. Set the minutes by pushing button , and

hours with button .

B C

2. Press button momentarily and the left LCD will display for 2 seconds and then change to one

of the following: with the date in the right LCD, or hours and

minutes in both LCD’s. If are displayed in the left LCD, press

again to display hours and minutes currently set for the alarm time.

Note - While adjusting the left LCD (hour) setting, the right LCD

(minutes) will display if digital time is set to standard

time mode. If digital time is in 24 hour military time mode, the

right LCD will display minutes. Pressing buttons or for longer

than 1 second will advance the hours and minutes rapidly.

B C

4. When finished setting hours and minutes, press button ; the left LCD will display for 2 seconds

followed by indicating the alarm’s mode and the right LCD will display the date.

5. To set alarm state, press and hold button until the left LCD changes from or

Cto to

Note - To test the alarm, press and hold ; the alarm should produce a beeping tone. D

Setting the Alarm

6. For the final time setting step, turn the crown and adjust the minute hand to MATCH the minutes

set in the right LCD with button in previous step 4. Set the current time by pushing in the crown to

position while using an accurate time signal. Screw down the setting crown to finish the setting

procedure.

Set the date with button and the month with button . Pressing buttons or for longer than 1

second will advance the date and month rapidly.

B C B C

Setting Time Zones/Leap Year

February 28 will normally change to March 1 and only needs to be adjusted on February 29 every four

years to accommodate leap years.

C H A S E - D U R E R

8 4

Correcting for Leap Year

1. Pull setting crown out to position and turn the hour hand counterclockwise (backwards) 24 hours

or two revolutions.

3. Screw down the setting crown to finish.

2. Push setting crown back to position and the right LCD (date) will display the correct date

Set crown in

position 2 to

only the hour hand

adjust

1. Pull setting crown out to position and turn to set the hour hand to another time zone when

traveling, or to adjust for Daylight Savings.

Setting Time Zones

Note - The hour displayed in the left LCD will also

change in synchronization with the hour hand!

If you wish to retain the original time zone,

pull setting crown to position and

press button to set LCD’s to time mode.

Reset the current hour on the left LCD

by pushing button until original time is

displayed.

Please note that the LCD time is used for the

Alarm function! If you wish to have the Alarm

synchronized to the hour hand, then the LCD

and hour hand must be set to the same time.

Resetting Chronograph Hands to Zero

C H A S E - D U R E R

8 4

The chronograph hands can be set at zero or another time zone.

Set the counter at 012 hour

Set the counter at 030 minute

Set the counter at 060 second

Note: Pressing PUSHBUTTONS momentarily will advance hands one index mark at a time.

To advance hands rapidly, press PUSHBUTTONS longer than 1 second .

Setting crown in position

for all adjustments

Timing Mode • Simple Chronograph Function

ADD FUNCTION: Order in which pushbuttons should be pressed.

Reset to zero

START STOP

Read

START STOP

Read

1234X

Setting crown in

position 1

START

STOP

Reset to

Zero

C H A S E - D U R E R

8 4

Note - The left LCD will display after step (STOP) until Reset to zero ( ) .

The right LCD will display hundredths of a second until Reset to zero.

Note* Step (or ) may be repeated as many

as necessary; Step before is the final reading.

times

to order of functions

Timing Mode • Split-Time or Intermediate Times Function

START

RESTART

(catching up)

SPLIT 1

Read

TIME 1

0 hour

15 minutes

26 seconds

25/100 second

RESTART

(catching up)

SPLIT 2

Read

TIME 2

1 hour

32 minutes

06 seconds

83/100 second

Read

LAST TIME

2 hours

57 minutes

03 seconds

74/100 second

STOP

Note* Step (or ) may be repeated as many

as necessary; Step is the final reading.

times

to order of functions

124

Crown set

in position 1

Reset to

Zero

C H A S E - D U R E R

8 4

C H A S E - D U R E R

8 4

C H A S E - D U R E R

8 4

C H A S E - D U R E R

8 4

Inhaltsverzeichnis

Andere Chase-durer Betrachten Handbücher

Chase-durer

Chase-durer STRIKE FORCE GMT Bedienungsanleitung

Chase-durer

Chase-durer Trackmaster Pro Bedienungsanleitung

Chase-durer

Chase-durer Condor Automatic Bedienungsanleitung

Chase-durer

Chase-durer XANADU Bedienungsanleitung

Chase-durer

Chase-durer COMBAT COMMAND GMT Bedienungsanleitung

Chase-durer

Chase-durer 251.262 Bedienungsanleitung

Chase-durer

Chase-durer Warhawk Bedienungsanleitung

Chase-durer

Chase-durer Falcon Command Bedienungsanleitung

Chase-durer

Chase-durer STARBURST Bedienungsanleitung

Chase-durer

Chase-durer SPECIAL FORCES Bedienungsanleitung

Chase-durer

Chase-durer Condor Automatic Bedienungsanleitung

Chase-durer

Chase-durer CLOUD CHASER AUTOMATIC Bedienungsanleitung

Chase-durer

Chase-durer Blackhawk Mach 3 Bedienungsanleitung

Chase-durer

Chase-durer CONQUEST AUTOMATIC Bedienungsanleitung

Chase-durer

Chase-durer OS10 Bedienungsanleitung

Chase-durer

Chase-durer Squadron Commander Bedienungsanleitung

Chase-durer

Chase-durer Trident FCX Bedienungsanleitung

Chase-durer

Chase-durer Fighter Command Bedienungsanleitung

Chase-durer

Chase-durer Warhawk Mechanical Bedienungsanleitung

Chase-durer

Chase-durer SPECIAL FORCES 1000 Bedienungsanleitung

Chase-durer

Chase-durer COMBAT COMMAND Bedienungsanleitung

Chase-durer

Chase-durer Abyss 1000 Professional Bedienungsanleitung

Chase-durer

Chase-durer Conquest Chronograph Bedienungsanleitung

Chase-durer

Chase-durer WING GMT Bedienungsanleitung

Beliebte Betrachten Handbücher anderer Marken

Pandora

Pandora WATCH2 Bedienungsanleitung

Casio

Casio QW-4343 Bedienungsanleitung

Suunto

Suunto X6 Bedienungsanleitung

Seiko

Seiko N830 Bedienungsanleitung

MotionX

MotionX 365 Bedienungsanleitung

Garmin

Garmin VENU SQ 2 Bedienungsanleitung

QCY

QCY Watch GTC Bedienungsanleitung

Canyon

Canyon Cindy CNE-KW41WP Bedienungsanleitung

Esq

Esq Watches Installationsanleitung

Crane

Crane AA5-CDSM-3A Bedienungsanleitung

Timex

Timex W-214 Bedienungsanleitung

DETOMASO

DETOMASO MATERA Bedienungsanleitung

Geemarc

Geemarc Watch N Shake Bedienungsanleitung

LORUS

LORUS W590 Bedienungsanleitung

STENLILLE

STENLILLE Actío Bedienungsanleitung

Casio

Casio 5594 Bedienungsanleitung

Sinn

Sinn HUNTER'S WATCH 3. Edition Bedienungsanleitung

Slazenger

Slazenger SLZ800 Bedienungsanleitung