Check-line QB-LED Bedienungsanleitung

CHECK•LINE®

BY ELECTROMATIC

QB-LED & QBS-LED

STROBOSCOPES

Operating Manual

TABLE OF CONTENTS

1.0 Introduction ………………………………………………………..…................... 02

1.1 Scope of delivery

1.2 Precautions when using

2.0 Overview ................................................................................................................. 03

2.1 Connections, controls and settings

2.2 Display

3.0 Set-Up ................................................................................................................. 05

3.1 Connections

3.2 Set-up steps

3.3 Connect the trigger

4.0 Operation ................................................................................................................. 06

4.1 Controls

4.2 Display

4.3 Standard mode

4.4 Pro mode

4.5 QBS-LED

4.6 Operating modes

5.0 Determining An Object’s Actual Rotational Speeds ............................................ 15

6.0 Technical Data and Accessories ............................................................................. 17

7.0 Faactory Reset ....................................................................................................... 18

8.0 Warranty ................................................................................................................. 19

IMPORTANT: This device is used for inspecting the movement of rotating and

vibrating objects. It may only be used in accordance with these instructions. The

device must not be opened. Modications to the device are not permitted. The

manufacturer shall not be liable for damage resulting from incorrect use or use

contrary to the intended use. Warranty claims will also be invalidated in this event.

– 1 –

– 2 –

1.0 INTRODUCTION

The Check-Line QB-LED is a hand-held, battery-powered stroboscope featuring

extremely bright LEDs for the highest light output in its class. Designed for machinery

observation, visual inspection and motion analysis, its robust design is suitable for use in

the toughest industrial environments.

1.1 Scope of Delivery

Check that you have received all of the following:

• Stroboscope: QB-LED design (40 LEDs, no laser)

or QBS-LED design (118 LEDs, with laser)

• Operating instructions

• Calibration certicate

• Charger with connector set

• Trigger plug

• Reective tapes (QBS-LED only)

• Handle

• Foam-tted, plastic carrying case

Note: This device is suitable for use in residential, commercial and industrial area.

1.2 Precautions when using

Risk of injury! Laser class 2: The stroboscope QBS-LED is tted with a

class 2 laser. This is located at the front of the device. The laser beam can damage

eyes. For this reason, do not stare directly at the laser beam and never direct it at

people or animals. Wavelength: 650 nm, output: 1 mW.

Risk of Injury! Flashing lights can cause retina damage: The

stroboscope QB-LED and QBS-LED versions are tted with 40/118 LEDs

respectively. These produce potentially dangerous optical radiation, which can

cause retina damage. Do not stare directly at the light and never direct it at people

or animals.

Risk of injury! Moving objects appear still or in slow motion in stroboscopic

light. Do not touch such objects under any circumstance.

Risk of injury! The device may not be used in potentially explosive areas.

Risk of injury! Stroboscopic light can trigger epileptic seizures in

persons at risk.

– 3 –

2.0 OVERVIEW

2.1 Connections, controls and settings (QB-LED QBS-LED)

(A) CHARGE = charging socket

(B) INPUT = input for external trigger /24 V power supply for sensors

(D) Rotary/push knob

(E) Selector switch: OFF, FREQUENCY, BRIGHT, MENU, LASER*

*NOTE: LASER Mode only available on QBS-LED model.

OFF

FREQUENCY

BRIGHT

LASER

PRESS: FLASH ON/OFF

Reset 5 sec.CHARGE

INPUT

(A)

(E)

(D)

(B) (C)

Fig.1 - Stroboscope QB-LED and QBS-LED

– 4 –

(1) (2) (3)

(4)

(5)

(6) (7)

(8) (9)

(10) (11)

(12) (13)

2.2 Display

(1) Brightness in μs and/or degrees (BRIGHT)

(2) Delay in ms and/or degrees (DELAY)

(3) Phase shift (PHASE)

(4) Unit of frequency in rpm, Hz and/or FPM

(5) Value

(6) Multiplier (MULT.)

(7) Trigger divider (DIV.)

(8) Slow motion (SLOW)

(9) Trigger signal edge (TRIG.)

(10) Internal/external trigger (INT / EXT)

(11) Store / read parameters (MEMORY IN / MEMORY OUT)

(12) Pro mode (P)

(13) Battery status – full, half full or low

Fig. 2 - Display

– 5 –

3.0 SETUP

3.1 Connectors (see Fig. 1)

3.2 Set-up steps

Please follow the steps below when setting up the device:

1. Charge the device by plugginh the charger into the CHARGE (A) socket to the

rear of the device (see Fig. 1)

2. Direct the device at a moving object and switch it on. Turn the selector switch (E)

one notch to the left to “FREQUENCY.”

The device will start to ash immediately. For this reason, do not

direct it at people or animals.

NOTE: The device will ash at the frequency that was set most recently. The display

shows the selected ash frequency in the unit that was set most recently (rpm, Hz or

FPM). If the ash frequency coincides with the frequency of the motion, a static

image appears.

3.3 Connect the trigger

The device has the option of being externally triggered.

DO NOT trigger the device with signals in excess or 300,000 FPM.

Material damage may occur.

NOTE: Use only original material from the manufacturer to connect the trigger signal.

The trigger input is isolated and is suitable for PNP

and NPN signals. A trigger plug suitable for this

input socket is included with the device.

1. Plug the trigger plug into the input socket

INPUT (B).

2. Screw in trigger plug.

3. Assign the connection socket as per Fig. 3.

NOTE: The device must be manually switched

between external and internal trigger signals (see

How select an internal/external trigger, page 9).

(EN 60130-9)

2 nc

3 GND

5 -Trigger

Fig. 3 - Assignment of the

connection socket.

No. Marking Term Description

(A) CHARGE Charging Socket Device is charged using a charger

(B) INPUT Input socket Input for external tripper/24 V

power supply

– 6 –

4.0 OPERATION

Note: This device comes in two versions.

• QB-LED (40 LEDs, no laser)

• QBS-LED (118 LEDs, with laser)

Both versions are available in Standard and Pro modes (see section 4.3, Standard mode

and section 4.4, Pro mode).

4.1 Controls

No. Term Description

(D Rotary/Push Knob • Turn the knob to select the value and push to conrm. The

adjustment increment depends upon the rotational speed.

• Turning the knob while simultaneously pushing it, effects the

adjustment increment in steps of 100.

• The ash can be turned off by pushing the knob once and

turned on again by pushing the knob once again.

(E) Selector Switch Choose between OFF, FREQUENCY, BRIGHT, MENU and LASER

(QBS-LED version) by turning the switch to the desired position

4.2 Display

Note: Preset values are retained in each mode (Standard or Pro mode)

OVERVIEW OF ADJUSTABLE PARAMETERS

Position of

the selector

switch (E)

Display Available with Functions of the rotary/push knob (D)

Internal

trigger

External

trigger

Set value Select parameter

OFF —

FREQUENCY FPM

BRIGHT BRIGHT deg •

MENU PHASE deg • • •

INT/EXT • • • •

Following functions are only available in the PRO mode

1/min/Hz/FPM • • •

MULT. • •

BRIGHT deg/µs • • •

DELAY ms • • •

DIV • •

SLOW • •

TRIG. • •

MEM IN • • •

MEM OUT • • •

(4) FREQUENCY FPM Frequency selection; FPM: ashes per

minute

- Turning the knob while pushing

it simultaneously, the adjustment

increment is effected in steps of 100.

- The ash can be turned off by

pushing the knob once and turned

on again by pushing the knob once

again.

How to select FREQUENCY

1. Turn the selector switch (E) to the FREQUENCY position. All settings, will appear in the display for a few

seconds, followed by S

2. Select the desired frequency by turning the rotary/push knob (D).

– 7 –

4.3 Standard Mode

NOTE: Not all of the setting shown in Fig 2 are available in Standard Mode.

No. Position of the

Selector Switch

(E)

Adjustable

Parameters

Description

(4) OFF — Device is switched off

(1) BRIGHT BRIGHT deg Selection of brightness

(in 1/1,000 degrees)

Brightness (BRIGHT in deg)

Flash duration: This function allows the ash duration to be adjusted, which inuences the brightness

and focus of the object being viewed. In the Standard mode, this setting can only be made in relative form

(degrees), whereas the Pro mode also features the additional setting of measuring brightness in absolute

form (microseconds).

– 8 –

No. Position of the

Selector Switch

(E)

Adjustable

Parameters

Description Display

(3) MENU PHASE deg:

0…359

Delay setting between the trigger signal

and ash (in degrees relative to the

frequency

Phase sift (PHASE in deg)

Phase shift setting (in degrees, relative to the frequency) between the trigger signal and ash. This value

allows a xed angle to be set between the trigger signal and ash.

• Example without external connection: The viewing position can be extremely precisely adjusted without

changing the ash frequency. You can shift the viewing position within a movement cycle.

• Example with external connection: The external trigger signal is triggered before the desired observation

point (= ash position of the stroboscope). This would mean that the connected stroboscope would

regularly ash too early. The PHASE deg setting adjusts the delay, altering the ash position of the

stroboscope by a set angle. This setting is not affected by the current rotational speed, which means that

the stroboscope will ash at the desired position even during rotational speed uctuations or during the

start-up period.

How to select in the MENU

1. Turn the selector switch (E) to the MENU position.

2. Select which parameter (e.g. PHASE deg) you want to change by turning the rotary/push knob (D).

3. Push the rotary/push knob (D) to conrm a parameter selection. The number shown in the display will

begin to ash.

4. Select the desired value by turning the rotary/push knob (D.)

5. Conrm and exit selection by pushing the rotary/push knob (D).

The setting is now active.

NOTE: The display and adjustable value can be changed by turning the rotary/push knob (D).

– 9 –

No. Position of the

Selector Switch

(E)

Adjustable

Parameters

Description Display

(10) MENU INT /EXT Internal /external trigger

How to select an internal / external trigger

1. Turn the selector switch (E) to the MENU position.

2. Select the INT / EXT parameter by turning the rotary/push knob (D).

3. Push the rotary/push knob (D) to conrm the parameter selection. The display will now show the

selection of INT and EXT parameters, the active setting will begin ashing.

4. Select the desired parameter by turning the rotary/push knob (D).

5. Conrm and exit selection by pushing the rotary/push knob (D).

The setting is now active.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Check-line Prüfgeräte Handbücher

Check-line

Check-line CP-425-KIT Bedienungsanleitung

Check-line

Check-line LS-9-12000 Bedienungsanleitung

Check-line

Check-line NS-600 Bedienungsanleitung

Check-line

Check-line TI-25S Bedienungsanleitung

Check-line

Check-line MiniTest 7200 FH Handbuch

Check-line

Check-line FGV-XY Bedienungsanleitung

Check-line

Check-line DT-725 Bedienungsanleitung

Check-line

Check-line TTC Series Bedienungsanleitung

Check-line

Check-line PK2 Bedienungsanleitung

Check-line

Check-line DT-311D Bedienungsanleitung

Check-line

Check-line TSV-1000 Bedienungsanleitung

Check-line

Check-line DS-2000LED Bedienungsanleitung

Check-line

Check-line TI-25P Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung