Checkpoint 21400 Platform Bedienungsanleitung

Classification: [Unrestricted] — For everyone | P. 1

Slide Rail Installation Instructions for the Check

Point 21400 Platform

Supports racks 29 - 37 inches in depthSlide Rail Kit

Screws for mounting

inner rail to chassis

(8/10) required

Screws/Nuts for

mounting brackets

to outer rail

(8 pair required)

Screws/Washers for

mounting rail brackets

to rack posts

(8 pair required)

Screws/Washers for

mounting platform’s

ear brackets to the

rack posts.

(4 typically required)

4 Rail Brackets

2 Slide Rails (includes Inner, Middle and Outer rail sections)

Classification: [Unrestricted] — For everyone | P. 2

Removing Inner Rail

1. Fully extend the rail assembly as shown below in figure below. The finger tab (D) for

the extension safety lock is revealed.

2. Press the finger tab and slide the inner rail (C) from the middle rail (B) until it completely

separates. (Note: The Middle and Outer rail can not be separated.)

3. Repeat Steps 1 and 2 for 2nd rail

Attach Inner Rail to Chassis

1. Position an inner rail along one side of the chassis with the rail’s notched end (A)

extending out the back of the chassis.

2. Align the screw holes (B) in the rail with the screw holes on the chassis, and fasten it

with 4 x screws (C)

3. Repeat Steps 1 and 2 for the 2nd rail on other side of chassis

Classification: [Unrestricted] — For everyone | P. 3

Mounting Brackets to Rails

Rail Bracket

Extend Outer Rail on side that has 3 holes, so that

there is access to holes from the inside.

Inner Hole Location

Using this screw/nut pair, push screw from the

inside, through the rail and bracket, and then

partially tighten the nut. Using the inner hole will

allow for mounting to shorter racks (29”).

Classification: [Unrestricted] — For everyone | P. 4

Extend other side of rail to see the large holes on

middle rail. These holes will provide access to the

outer rail’s holes for adding the screws/nuts when

securing rail bracket.

Middle rail access holes

Outer Rail mounting holes

Repeat installation of screw/nut pair for 2

hole for

bracket.

Classification: [Unrestricted] — For everyone | P. 5

Slide middle rail in so that the its access holes line

up with the outer rail’s mounting holes

Using this screw/nut pair, push screw from the

inside, through the rail and bracket, and then

partially tighten the nut. Using the inner hole will

allow for mounting to shorter racks (29”).

Classification: [Unrestricted] — For everyone | P. 6

Installing the Outer Rail

1. Install the front of the outer rail to the rack, using the screw/washer pairs shown. (Note:

the front of the rail is the side where the middle rail can extend out from.) Do not

completely tighten these front screws. Leave them loose enough to allow adjusting the

bracket position so that the middle rail can slide out the front smoothly. Once positioned

properly, the screws can be tightened.

Repeat installation of screw/nut pair for 2

hole for

bracket.

Repeat the procedures on the previous pages for

mounting the 2 rail brackets to the second slide rail

Ensure that the middle rail slides smoothly out

the front of the rack, before tightening the rail

bracket to the rack.

Classification: [Unrestricted] — For everyone | P. 7

2. Extend the outer rail bracket (A) to the back of the rack, and using 2 screw/washer

pairs, firmly tighten the bracket to the back of the rack.

3. From the side of the rack, tighten the 4 nuts that were used to partially secure the

brackets to the rails. (See alternate procedure on next page if access to the side of the

rack is not possible.)

4. Repeats steps from previous page and this page for attaching the 2nd outer rail to other

side of rack. Ensure that the brackets/rails are at the same height of rack.

5. Adjust the middle rail to about 2.5 inches from the front rack post. The length may be a

little different on different styles of cabinet. (If attaching rails to a 29 inch rack, there

may not be enough space to slide the middle rail back. If so, the ear bracket of platform

may not reach the front of rack.)

Classification: [Unrestricted] — For everyone | P. 8

6. From the side of the rack, tighten the 4 hex nuts (A) that were used to partially secure

the brackets to the rails. (See alternate procedure on next page if access to the side of

the rack is not possible.)

Installing the Outer Rail – Alternate Procedure.

1. If access to the side of the rack is not possible, then the installer must first pre-measure

the depth of the rack from front to back.

2. On the bench, extend the rails to the measured depth and tighten the 4 nuts used to

attach the rail brackets to the rails.

3. Using the 4 x screw/washer pairs, attach the rail to the rack as described on previous

page.

4. Repeat Steps 1-3 for attaching the 2nd outer rail to other side of rack.

Pre-measure inside

depth of rack

Classification: [Unrestricted] — For everyone | P. 9

Installing the Platform on the Rails

1. Fully extend the left and right rails until the extension locks have engaged and the rail

will not push back. The rail is now ready to receive the platform.

2. With 2 people carefully lift the chassis and insert the inner rails on the platform into the

rails on the rack.

3. Slide the chassis toward the rear of the cabinet until the rails lock together.

4. Press and hold down the finger tabs (A) on both middle extension locks while sliding the

platform towards the rear.

Classification: [Unrestricted] — For everyone | P. 10

5. Slide the platform into the rack until the platform’s ear brackets are against the rack’s

front posts.

6. Use the screw/washer pair to secure platform to rack posts

Inhaltsverzeichnis

Andere Checkpoint Server Handbücher

Checkpoint

Checkpoint Smart-1 150 Bedienungsanleitung

Checkpoint

Checkpoint QUANTUM SMART-1 6000-L Bedienungs- und Sicherheitshinweise

Checkpoint

Checkpoint Integrity Advanced Server Bedienungsanleitung

Checkpoint

Checkpoint Smart-1 50 Bedienungsanleitung

Checkpoint

Checkpoint Smart-1 25 Bedienungsanleitung

Checkpoint

Checkpoint 21000 Appliances G-70 Bedienungsanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung