Chiayo QR-2000N Bedienungsanleitung

QR-2000N

UHF 100/16-Channel Wireless Microphone System

ISO 9001

ISO 14001

OHSAS 18001

GREEN PRODUCT

Operation manual

IS O

140 01

REG IS TER E D

O H S A S

180 01

REG IS TER E D

-1-

Thank you purchasing CHIAYO’s professional modular wireless system. Please read this

manual thoroughly to be familiarized with the function of each part before use.

Parts and functions of QR-2000N

Front

1.Power switch.

2.Channel A: RECEIVER module, also can be MP3 (RECORDER) PLAYER,

BLUETOOTH RECEIVER, or TRANSMITTER module.

3.Channel B: TRANSMITTER module, also can be RECEIVER, MP3 (RECORDER)

PLAYER, BLUETOOTH RECEIVER module.

4.Transmitter antenna.

Rear

1.Antenna B

2.Balanced audio output (channel B) for only RECEIVER module.

3.Unbalanced audio output for ANY module / input for only TRANSMITTER or MP3

RECORDER PLAYER module (channel B)

4.Repeater ON/OFF. Switch ON when TRANSMITTER module is to be used for audio

signal transmission of the other module, which can be RECEIVER, MP3 (RECORDER)

PLAYER or BLUETOOTH RECEIVER module. Switch OFF if not.

5.Balanced audio output (channel A) only RECEIVER module.

6.Unbalanced audio output for ANY module / input for only TRANSMITTER or MP3

RECORDER PLAYER module (channel A)

7.DC-input

8.Antenna A

12 3

1 2 3 4 5 6 7 8

ISO 9001 / ISO 14001 / OHSAS 18001

-2-

Connection

There are two audio connecters on the rear of this unit, Mic-level balanced and Line-level

unbalanced. Use shielded audio cable for the connection between this unit and the

mixer/amp or audio source. If the mixer/amp has a 1/4"(6.3mm) phone jack, connect a

cable from the 1/4"(6.3mm) unbalanced audio output from the receiver to the mixer/amp.

If the mixer has an XLR input, connect a cable from the balanced XLR audio output from

the receiver to the mixer input. This 1/4"(6.3mm) phone jack also serves as the audio

input when using TRANSMITTER or MP3 RECORDER PLAYER module.

Installation

For best operation, this unit should be at least 1m above the ground and at least 1m away

from a wall or metal surface to minimize reflection. The transmitter should also be at least

1m away from a wall or metal surface to minimize reflection. The transmitter should also

be at least 1m away from the receiver.

Mounting

QR-2000N has a half-19"-casing design. It can be cabinet-mounted with either 1 or 2 units.

Individual kits for mounting 1 or 2 QR-2000N are available and please refer to below

assembly illustration.

-3-

SDR-5200M IrDA/SDR-5100M IrDA/SDR-5116M receiver modules

1.Channel indicator

2.Diversity A/B indicator

3.Audio signal indicator

4.IR sensor area (SDR-5200M IrDA/SDR-5100M IrDA)

5.Channel Selector

6.IRDA synchronizing button (SDR-5200M IrDA/SDR-5100M IrDA)

7.Squelch control

8.Power switch/volume control

First turn on the Power of the main unit. Then turn on the individual power of the receiver

module. Select a channel that corresponds to the transmitter. When transmitter is turned on,

either A or B diversity indicator will flash to indicate that signal has been received.

SQUELCH (SQ) setting

When a channel is in use and undesired interference signal is received, turn the SQ in

clockwise direction to make the receiver less sensitive and thus less susceptible to interference.

If this still does not solve the problem, it means this frequency is not applicable at current

position. Please switch over to the next channel.

Channel synchronizing of the receiver and microphone (SDR-5200M IrDA/SDR-5100M IrDA)

1.Limit the distance between the receiver and transmitter within 30cm.

2.Align both sensor areas

3.To change the receiver’s channel, please press the synchronizing button of the microphone.

The microphone will transmit synchronizing signal to the receiver and change its channel.

4.To change the microphone’s channel, please press the synchronizing button of the receiver.

The receiver will transmit synchronizing signal to the microphone and change its channel.

ISO 9001 / ISO 14001 / OHSAS 18001

-4-

RP-5016M/RP-5100M transmitter module

HI LOW

1.Channel indicator

2.Antenna socket (TNC type)

3.Channel selectors: Press ▲(up)▼(down) to increase/decrease channel number. Please

select a non-interfering frequency channel to those used in the receiver modules.

4.Power control

5.Unit GAIN control: This controls the GAIN level of interior audio sources.

6.3.5mm audio input jack

7.AUX IN GAIN control: This controls the GAIN level of external audio input.

8.Output power setting: LOW (left) for Low output power and HI (right) for high output power.

Low output power will reduce the RF transmission distance and High output power will

extend the possible RF transmission distance. However, if the module is installed on battery-

powered amplifiers, HIGH output power would reduce more operation time than LOW output

power since it requires more power for longer RF transmission.

DPR-500M MP3 recorder player module

1.LCD display

2.Press to return to previous track, press and hold to fast reverse.

3.Press to play/pause.

4.Press to go to next track, press and hold to fast forward.

5.Press to record.

6.Press to switch repeat modes.

7.Press to stop playing or recording.

8.IR sensor area

9.USB 2.0 input

10.USB/SD indicator: The LED flashes green during playing and red during recording. It lights

red if there is no track to play, lighting green when playing or recording stops.

11.SD card input

12.Power switch/volume control

remote control▲

-5-

Operating functions on the panel and the remote

※Extra attention to recording

1.Recordable only when USB/SD is detected.

2.Record files will be stored in the RECORD folder of USB/SD.

3.The files will be named as FILE_001, FILE_002, FILE_003…etc.

4.The name of a deleted track won’t be applied to its next one.

5.Recordable until FILE_999 appears with LCD displaying Num Full.

6.LCD displays USB FULL or SD FULL when insufficient memory left.

7.LCD displays SD LOK if the SD is locked.

8.Don’t remove the USB/SD during the recording process in case the interrupted track might

be damaged.

Operating function

On the panel

On the remote

Play/pause

Press II

Record

Press●to record and ■to stop.

Press REC to record and ■to stop.

Skip forward

Press I

PressI

Fast forward

Press and hold I

Skip backward

Press I

Fast backward

Press and hold I

Next folder

Press 

Previous folder

Press 

Track select (button #0-9)

input track number, then press II

USB/SD switch

Press USB/SD

Repeat mode switch

(ALL//SINGLE/FLDER)

Press MODE

Volume control

Press or

A-B section play

Press A-B to start, again to play

section and again to stop

Delete tracks

Press DEL to delete track and again

to confirm your delete

Mute

press MUTE to mute/recover

ISO 9001 / ISO 14001 / OHSAS 18001

-6-

BT-500mBluetooth receiver module

234

1.Power/volume control

2.LOCK LED

3.SCAN LED

4.PAIRING button

Matching instruction

1.Turn on BT-500m and both SCAN and LOCK LEDs will flash alternatively.

2.Activate Bluetooth on your device and search new external Bluetooth devices.

3.Find and connect to “Bluetooth Speaker” that appears on your option list.

4.Once connection is made, the LOCK LED will flash green.

5.Pressing PAIRING button can cut the connection.

-7-

UHF handheld microphones（SQ-6100 IrDA/SQ-2100 IrDA/SQ-1100 IrDA）

SQ-6100 IrDA

SQ-2100 IrDA

SQ-1100 IrDA

Parts and functions

SQ-6100 IrDA

SQ-2100 IrDA

SQ-1100 IrDA

Cartridge

Battery power LED

Power switch

LCD

Menu button

Setting button

IrDA synchronizing button

Battery compartment

Color cap

IrDA sensor area

Charging port

Battery installation & indicator

This microphone requires 2 x AA batteries to operate.

To install, remove the battery cover and slide the batteries into the battery compartment &

replace the battery cover.

Note: Batteries contain a corrosive acid that may leak and damage the microphone when

stored for a long period. Batteries should be removed from the microphone before storing

without use for more than 4 weeks.

When the microphone is switched ON a red LED (2) will blink once to indicate the batteries

installed are in good condition. If the LED remains illuminated the batteries have expired

and require replacement.

1 2 3 7

4 5 6

ISO 9001 / ISO 14001 / OHSAS 18001

-8-

Channel synchronizing of the receiver and microphone

1. Limit the distance between the receiver and transmitter within 30cm.

2. Align both sensor areas

3. To change the receiver’s channel, please press the synchronizing button of the microphone.

The microphone will transmit synchronizing signal to the receiver and change its channel.

4. To change the microphone’s channel, please press the synchronizing button of the receiver.

The receiver will transmit synchronizing signal to the microphone and change its channel.

Other settings（SQ-6100 IrDA）

1. Channel setting

Use MENU button to go to the CHANNEL/FREQUENCY page.︰

After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made.

Pressing SET/MENU buttons will increase/decrease the channel number. The corresponding

frequency will change accordingly. 3 seconds after selecting a channel, it will be automatically

saved.

2. Battery type setting

Use MENU button to go to the BATTERY TYPE page.︰

After pressing the SET button for 3 seconds, the cursor will flash to allow changes to be made.

Press SET button to select either NiMH (rechargeable battery) or AKLN (alkaline battery). 3

seconds after selecting a channel, it will be automatically saved.

Remark: NiMH battery must be selected when rechargeable battery is being used. Never select

AKLN (alkaline) when microphone is intended for charging as alkaline battery isn’t

rechargeable. Wrong battery selection will result in battery sensing electronics to display wrong

and misleading status information.

-9-

UHF belt-pack transmitters（SM-7100 IrDA/SM-6100 IrDA/SM-1100 IrDA）

SM-7100 IrDA/SM-6100 IrDA SM-1100 IrDA

Parts and functions

SM-7100 IrDA

SM-6100 IrDA

SM-1100 IrDA

Antenna

LCD

Cover release button

Power switch

IrDA synchronizing button

Menu button

Setting button

High-impedance gain control (GT)

Low-impedance gain control (MT)

Battery compartment

Audio mute switch

Battery power LED

IrDA sensor area

Mini XLR connector

Charging contacts

Battery installation & indicator

This belt-pack requires 2 x AA batteries to operate.

To install, open the battery cover using the cover release buttons and insert the batteries into

the battery compartment.

3 3

84 5

11 12

11 11

Andere Handbücher für QR-2000N

Andere Chiayo Mikrofonsystem Handbücher

Chiayo

Chiayo Q-818 Bedienungsanleitung

Chiayo

Chiayo IRX2 Bedienungsanleitung

Chiayo

Chiayo SDR-6200 IrDA Bedienungsanleitung

Chiayo

Chiayo IWM-202 Bedienungsanleitung

Chiayo

Chiayo SDR-5216 Bedienungsanleitung

Chiayo

Chiayo Stage-100 Series Bedienungsanleitung

Chiayo

Chiayo Smart 300 Bedienungsanleitung

Chiayo

Chiayo Live-100 series Bedienungsanleitung

Chiayo

Chiayo NDR-3100 Bedienungsanleitung

Chiayo

Chiayo IWR-200 Bedienungsanleitung

Chiayo

Chiayo COACH PRO Bedienungsanleitung

Chiayo

Chiayo RR-2000 Bedienungsanleitung

Chiayo

Chiayo R-1010 Bedienungsanleitung

Chiayo

Chiayo Q-200 Bedienungsanleitung

Chiayo

Chiayo UDR-500 Bedienungsanleitung

Chiayo

Chiayo SQ-6100 IrDAR Bedienungsanleitung

Chiayo

Chiayo IrDA-9000 Bedienungsanleitung

Chiayo

Chiayo DWR-5420 Bedienungsanleitung

Chiayo

Chiayo RRS-2000 Bedienungsanleitung

Chiayo

Chiayo R-1001 Bedienungsanleitung

Chiayo

Chiayo SDR-5100 IrDA Bedienungsanleitung

Chiayo

Chiayo QR-4000 U Bedienungsanleitung

Chiayo

Chiayo SDR-6200 IrDA Bedienungsanleitung

Chiayo

Chiayo AIR-812 Bedienungsanleitung

Beliebte Mikrofonsystem Handbücher anderer Marken

Paso

Paso R824 Bedienungsanleitung

Naxa

Naxa NAM-982 Bedienungsanleitung

Motorola

Motorola PMNN4461 Bedienungsanleitung

Xvive

Xvive U3 Bedienungsanleitung

Tekon

Tekon DUOS Bedienungsanleitung

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Bedienungsanleitung

Devine

Devine WMD-IE Bedienungsanleitung

LG LF-D7150 Bedienungsanleitung

GE S768DAV Bedienungsanleitung

LD U305 HBH 2 Bedienungsanleitung

Chainway

Chainway URA8 Bedienungsanleitung

ORATOR

ORATOR D860TD Bedienungsanleitung

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Bedienungsanleitung

Alpha Technologies

Alpha Technologies RBMS Bedienungsanleitung

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Bedienungsanleitung

Shure

Shure UA844 Bedienungsanleitung

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Bedienungsanleitung

Pyle

Pyle PDWM5000 Bedienungsanleitung