Chicago Electric 94533 Bedienungsanleitung

MAINTENANCE BATTERY CHARGER

12 Volt / 2 Amp Output

94533

OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at: http://www.harborfreight.com

sheet or any artwork contained herein may be reproduced in any shape or form without

the express written consent of Harbor Freight Tools.

For technical questions, please call 1-800-444-3353.

SAVE THESE INSTRUCTIONS

SAFETY WARNINGS AND PRECAUTIONS

Always wear ANSI-approved safety impact eye goggles during setup or use.

Maintain a safe working environment. Always keep the work area free of obstruc-

tions, grease, oil, trash, and other debris. Do not use this product in areas near

ﬂammable chemicals, dust, and vapors.

Read and understand all instructions and safety precautions as outlined in the

manufacturer’s manual of the battery with which this product will be used.

FIRE HAZARD! Never allow the red and black Battery Clamps to touch each

other or the same metal object.

WARNING! Lead acid batteries generate hydrogen gas during normal operation,

and even more gas is generated when the battery is charging. Hydrogen gas is

explosive and highly ﬂammable. Never smoke near a charging battery.

Plug the Charger into its electrical outlet only after it is connected to the

vehicle’s battery.

Do not attempt to start a vehicle with the Charger connected to its battery.

WARNING! If battery ﬂuid comes in contact with skin, wash with soap and water and

rinse with lemon juice and vinegar. If the ﬂuid comes into contact with eyes, ﬂush

with water for several minutes and contact a physician immediately. Never burn a

battery as it can explode in a ﬁre. Do not attempt to charge a leaking battery.

WARNING! People with pacemakers should consult their physician(s) before using

this product. Electromagnetic ﬁelds in close proximity to a heart pacemaker could

cause interference or failure of the pacemaker. In addition, people with pacemakers

should adhere to the following: Caution is necessary when near the coil, spark plug

wires, or distributor of a running engine.

SKU 94533 For technical questions, please call 1-800-444-3353 PAGE 2

OPERATING INSTRUCTIONS

To Charge A Battery Using The Battery Clamps:

NOTE: See the last page of this instruction sheet for a complete Parts List and

Assembly Diagram.

Make sure the transmission of the vehicle is in “PARK” and the emergency brake

has been set. Also, turn off the engine of the vehicle prior to connecting the Battery

Charger to the battery of the vehicle.

Attach the RED/POSITIVE (+) Battery Clamp of the Temporary Connection Cord (8)

to the POSITIVE battery terminal of the vehicle.

Attach the BLACK/NEGATIVE (–) Battery Clamp of the Temporary Connection Cord

(8) to the NEGATIVE battery terminal of the vehicle.

Connect the Temporary Connection Cord (8) to the Output Cord (3) of the Battery

Charger.

Plug the Power Cord (2) of the Battery Charger into the nearest 120 volt, grounded,

electrical outlet.

The RED (AC Power) light on the Main Unit (1) of the Battery Charger should be

illuminated. This light indicates the Main Unit is receiving 120 volt electrical power

from the electrical outlet.

The YELLOW (Charging) light on the Main Unit (1) of the Battery Charger should

be illuminated. This light indicates charging is taking place.

The GREEN (Charged) light on the Main Unit (1) of the Battery Charger will illuminate

when the vehicles’ battery is fully charged.

Once the vehicle’s battery is fully charged, unplug the Power Cord (2) from its 120 volt

electrical outlet. Disconnect the RED/POSITIVE (+) Battery Clamp of the Temporary

Connection Cord (8) from the POSITIVE battery terminal of the vehicle’s battery.

Then disconnect the BLACK/NEGATIVE (–) Battery Clamp from the Temporary

Connection Cord (8) from the NEGATIVE battery terminal of the vehicle’s battery.

Make sure to store all parts of the Battery Charger in a clean, dry, safe location out

of reach of children.

10.

SKU 94533 For technical questions, please call 1-800-444-3353 PAGE 3

To Charge A Battery Using The Ring Connectors:

Make sure the transmission of the vehicle is in “PARK” and the emergency brake

has been set. Also, turn off the engine of the vehicle prior to connecting the Battery

Charger to the battery of the vehicle.

Attach the RED/POSITIVE (+) Ring Connector of the Permanent Connection Cord

(4) to the POSITIVE battery terminal of the vehicle.

Attach the BLACK/NEGATIVE (–) Ring Connector of the Permanent Connection

Cord (4) to the NEGATIVE battery terminal of the vehicle.

Unplug the Connection Cord Cap (5) from the Permanent Connection Cord (4).

Connect the Permanent Connection Cord (4) to the Output Cord (3) of the Battery

Charger.

Plug the Power Cord (2) of the Battery Charger into the nearest 120 volt, grounded,

electrical outlet.

The RED (AC Power) light on the Main Unit (1) of the Battery Charger should be

illuminated. This light indicates the Main Unit is receiving 120 volt electrical power

from the electrical outlet.

The YELLOW (Charging) light on the Main Unit (1) of the Battery Charger should

be illuminated. This light indicates charging is taking place.

The GREEN (Charged) light on the Main Unit (1) of the Battery Charger will illuminate

when the vehicles’ battery is fully charged.

Once the vehicle’s battery is fully charged, unplug the Power Cord (2) from its 120

volt electrical outlet. Disconnect the Permanent Connection Cord (4) from the Output

Cord (3) of the Battery Charger.

NOTE: If desired, the Battery Charger may be left connected to maintain the battery’s

charge.

Plug the Connection Cord Cap (5) back into the Permanent Connection Cord (4).

This allows you to leave the Permanent Connection Cord attached to the vehicle’s

battery. Always make sure the Permanent Connection Cord is positioned away

from hot or moving parts of the vehicle’s engine.

Make sure to store all parts (except the Permanent Connection Cord) in a clean, dry,

safe location out of reach of children.

10.

11.

12.

SKU 94533 For technical questions, please call 1-800-444-3353 PAGE 4

PARTS LIST & ASSEMBLY DIAGRAM

Part Description Qty. Part Description Qty.

1 Main Unit 1 5 Connection Cord Cap 1

2 Power Cord 1 6 Fuse Holder 1

3 Output Cord 1 7 3 Amp Fuse 1

4 Permanent Connection

Cord

1 8 Temporary Connection

Cord

Problem: The Battery Charger is plugged into an electrical outlet, but no lights on

the Main Unit (1) are illuminated.

Possible Solutions:

Check to make sure the Power Cord (2) is properly plugged into a working 120

volt, grounded electrical outlet.

Check to make sure the connections to the vehicle’s battery posts are secure.

Open the Fuse Holder (6) to inspect the 3 AMP Fuse (7). If necessary, replace

the Fuse.

To Charge A Battery Using The Screw Connectors

(Not Shown)

To Charge A Battery Using The Battery Clamps

TROUBLESHOOTING

NOTE: NO REPLACEMENT PARTS ARE AVAILABLE FOR THIS PRODUCT.

SKU 94533 For technical questions, please call 1-800-444-3353 PAGE 5

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIA-

GRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANU-

FACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY

OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO REPLACE ANY

PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR

EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD

BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY

THE BUYER. THE BUYER ASSUMES ALL RISKS AND LIABILITY ARISING OUT OF

HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS

THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT

PARTS THERETO.

Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,

and warrants to the original purchaser that this product is free from defects in materials and workmanship for

the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or

indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of

maintenance.We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,

special or consequential damages arising from the use of our product. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.THIS

WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING

THE WARRANTIES OF MERCHANTABILITY AND FITNESS.

To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid.

Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection

veriﬁes the defect, we will either repair or replace the product at our election or we may elect to refund the purchase

price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our

expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of

our warranty, then you must bear the cost of returning the product.

This warranty gives you speciﬁc legal rights and you may also have other rights which vary from state to state.

3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353

Limited 90 day warranty

Inhaltsverzeichnis

Andere Chicago Electric Akkuladegerät Handbücher

Chicago Electric

Chicago Electric 93258 Bedienungsanleitung

Chicago Electric

Chicago Electric 67104 Installationshandbuch

Chicago Electric

Chicago Electric 91325 Bedienungsanleitung

Chicago Electric

Chicago Electric 45005 Bedienungsanleitung

Chicago Electric

Chicago Electric 42292 Bedienungsanleitung

Chicago Electric

Chicago Electric 66783 Installationshandbuch

Chicago Electric

Chicago Electric 3418 Bedienungsanleitung

Chicago Electric

Chicago Electric 92416 Bedienungsanleitung

Chicago Electric

Chicago Electric 42292 Bedienungsanleitung

Chicago Electric

Chicago Electric 47618 Installationshandbuch

Chicago Electric

Chicago Electric 3418 Stücklistenhandbuch

Chicago Electric

Chicago Electric 93781 Kurzanleitung

Chicago Electric

Chicago Electric 68859 Montageanleitung

Chicago Electric

Chicago Electric 65834 Installationshandbuch

Chicago Electric

Chicago Electric 92426 Bedienungsanleitung

Chicago Electric

Chicago Electric 45005 Installationshandbuch

Chicago Electric

Chicago Electric 99857 Installationshandbuch

Chicago Electric

Chicago Electric 66718 Installationshandbuch

Chicago Electric

Chicago Electric 90604 Bedienungsanleitung

Chicago Electric

Chicago Electric 65042 Installationshandbuch

Chicago Electric

Chicago Electric 95000 Stücklistenhandbuch

Chicago Electric

Chicago Electric 92775 Bedienungsanleitung

Chicago Electric

Chicago Electric 95000 Kurzanleitung

Chicago Electric

Chicago Electric 46944 Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung