Chicago Electric 91797 Bedienungsanleitung

ELECTRIC FIREPLACE HEATER

WITH SINGLE GLASS DOOR

Model

91797

ASSEMBLY AND OPERATING INSTRUCTIONS

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

tained herein may be reproduced in any shape or form without the express written consent of Harbor Freight

Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual

product may differ slightly from the product described herein. Tools required for assembly and service may not

be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Revised Manual 10d

Page 2SKU 91797 For technical questions, please call 1-800-444-3353

SPECIFICATIONS

SAVE THIS MANUAL

You will need the manual for the safety warnings and precautions, assembly instructions,

operating and maintenance procedures, parts list and diagram. Keep your invoice with this

manual. Write the invoice number on the inside of the front cover. Keep the manual and

invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS.Failure to follow all instructions

listed below may result in electric shock, ﬁre, and/or serious injury.

SAVE THESE INSTRUCTIONS

WORK AREA

1. Keep the area surrounding this appliance clean and orderly.

2. Do not operate this heater in explosive atmospheres, such as in the presence of

ﬂammable liquids, gases, or dust.

REV 07j; 08d

The maximum room size of the heater is 400 square foot.

ITEM DESCRIPTION

Power Requirements 120 VAC, 60 Hz, 15 Amps

Heater Settings 750 and 1500 Watts

Heater Controls Fan On/Off switch; 2 -2750W On/Off switches;

Fire light On/Off switch; Temperature thermo-

state knob; Fire light brightness knob; Remote

Control Unit

Line Cord Two-prong polarized plug; 16 AWG x 2C; UL

listed

Light Bulbs 2 - 60W candelabra bulbs

Overall Dimensions 20-3/8 (L) x 11-1/2 (W) x 22-3/4 (H) inches

Weight 39 Lbs.

Page 3SKU 91797 For technical questions, please call 1-800-444-3353

Electrical Safety

3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges,

and refrigerators. There is an increased risk of electric shock if your body is

grounded.

4. Do not expose appliances to rain or wet conditions. Water entering a appliance

will increase the risk of electric shock.

5. Grounded products must be plugged into an outlet properly installed and

grounded in accordance with all codes and ordinances. Never remove the

grounding prong or modify the plug in any way. Do not use any adapter plugs.

Check with a qualiﬁed electrician if you are in doubt as to whether the outlet

is properly grounded. If the product should electrically malfunction or break down,

grounding provides a low resistance path to carry electricity away from the user.

6. Double insulated appliances are equipped with a polarized plug (one blade is

wider than the other). This plug will ﬁt in a polarized outlet only one way. If

the plug does not ﬁt fully in the outlet, reverse the plug. If it still does not ﬁt,

contact a qualiﬁed electrician to install a polarized outlet. Do not change

the plug in any way. Double insulation eliminates the need for the three wire

grounded power cord and grounded power supply system.

7. Do not abuse the Power Cord. Never use the Power Cord to pull the Plug from

an outlet. Keep the Power Cord away from heat, oil, sharp edges, or moving

parts. Replace damaged Power Cords immediately. Damaged Power Cords

increase the risk of electric shock.

Personal Safety

8. Stay alert. Watch what you are doing, and use common sense when operating

this product.

9. Avoid accidental starting. Be sure the Fan Switch is off before plugging in.

Tool Use and Care

10. Do not use this appliance if any switch or thermostat does not work properly.

11. Disconnect the Power Cord Plug from the power source before making any

adjustments to the appliance. Such preventive safety measures reduce the risk of

starting the appliance accidentally.

Service

12. Appliance service must be performed only by qualiﬁed repair personnel.

Service or maintenance performed by unqualiﬁed personnel could result in a risk of

injury.

Page 4SKU 91797 For technical questions, please call 1-800-444-3353

13. When servicing an appliance, use only identical replacement parts. Follow

instructions in the “Inspection, Maintenance, And Cleaning” section of this

manual. Use of unauthorized parts or failure to follow maintenance instructions may

create a risk of electric shock or injury.

SPECIFIC SAFETY RULES FOR THIS PRODUCT

1. Maintain labels and nameplates on the Fireplace Heater. These carry important

information. If unreadable or missing, contact Harbor Freight Tools for a replacement.

2. Avoid ﬁres and explosions. Never place the Fireplace Heater near room curtains

or other ﬂammable materials. The ﬂoor on which the Fireplace Heater sits must be

nonﬂammable and free of debris. Never use near ﬂammable vapors or liquids.

3. Maintain a safe working environment. Keep the work area well lit. Make sure there

is adequate surrounding space. Always keep the work area free of obstructions,

grease, oil, trash, and other debris. Do not use this product in areas near ﬂammable

chemicals, dusts, and vapors. Do not use this product in a damp or wet location.

4. Avoid unintentional starting. Make sure you are prepared to begin work before

turning on the Fireplace Heater.

5. Do not force the Fireplace Heater. This product will do the work better and safer at

the capacity for which it was designed.

6. Always unplug the Fireplace Heater from its electrical outlet before performing

and inspection, maintenance, or cleaning procedures.

7. Never leave the Fireplace Heater unattended while running. Turn power off if you

have to leave the room.

8. Use proper extension cord. If an extension cord is used, use the proper type as

listed in the table on page 7. Keep extension cord off the ground and away from water.

9. Connect to a GFCI outlet. Always connect the Line Cord to a Ground Fault Circuit

Interrupter (GFCI) protected electrical outlet.

GROUNDING

Note: This product comes with a two-prong, polarized plug.

WARNING!

Improperly connecting the grounding wire can result in the risk of electric

shock. Check with a qualiﬁed electrician if you are in doubt as to whether

the outlet is properly grounded. Do not modify the power cord plug provided

with the tool or product. Never remove the grounding prong from the plug.

Do not use the tool if the power cord or plug is damaged. If damaged, have

it repaired by a service facility before use. If the plug will not ﬁt the outlet,

have a proper outlet installed by a qualiﬁed electrician.

Page 5SKU 91797 For technical questions, please call 1-800-444-3353

Grounded Tools: Appliances with Three Prong Plugs

1. Appliances marked with “Grounding Required” have a three wire cord and three prong

grounding plug. The plug must be connected to a properly grounded outlet. If the

appliance should electrically malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user, reducing the risk of electric

shock. (See Figure A.)

2. The grounding prong in the plug is connected through the green wire inside the cord

to the grounding system in the appliance. The green wire in the cord must be the only

wire connected to the appliance’s grounding system and must never be attached to an

electrically “live” terminal. (See Figure A.)

3. Your appliance must be plugged into an appropriate outlet, properly installed and

grounded in accordance with all codes and ordinances. The plug and outlet should

look like those in the following illustration. (See Figure A.)

Double Insulated Appliances: Appliances with Two Prong Plugs

4. Appliances marked “Double Insulated” do not require grounding. They have a special

double insulation system which satisﬁes OSHA requirements and complies with

the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard

Association, and the National Electrical Code. (See Figure B above.)

5. Double insulated appliances may be used in either of the 120 volt outlets shown in the

following illustration. (See Figure B above.)

EXTENSION CORDS

1. Grounded tools require a three wire extension cord. Double Insulated tools can use

either a two or three wire extension cord.

2. As the distance from the supply outlet increases, you must use a heavier gauge

extension cord. Using extension cords with inadequately sized wire causes a serious

drop in voltage, resulting in loss of power and possible tool damage. (See Table A.)

3. The smaller the gauge number of the wire, the greater the capacity of the cord. For

example, a 14 gauge cord can carry a higher current than a 16 gauge cord. (See

Table A.)

4. When using more than one extension cord to make up the total length, make sure

each cord contains at least the minimum wire size required. (See Table A.)

Figure A Figure B

Page 6SKU 91797 For technical questions, please call 1-800-444-3353

5. If you are using one extension cord for more than one appliance, add the nameplate

amperes and use the sum to determine the required minimum cord size. (See Table

A.)

6. If you are using an extension cord outdoors, make sure it is marked with the sufﬁx

“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

7. Make sure your extension cord is properly wired and in good electrical condition.

Always replace a damaged extension cord or have it repaired by a qualiﬁed electrician

before using it.

8. Protect your extension cords from sharp objects, excessive heat, and damp or wet

areas.

Table B

RECOMMENDED MINIMUM WIRE GAUGE FOR

EXTENSION CORDS* (120/240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD LENGTH

25’

50’

75’

100’

150’

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

TABLE A

* Based on limiting the line

voltage drop to ﬁve volts at

150% of the rated amperes.

The Fireplace Heater comes fully assembled

from the factory, and is ready for operation.

When unpacking, check to make sure that

all the parts are included. Refer to the

Assembly Drawing and Parts List at the end

of this manual. If any parts are missing or

broken, please call Harbor Freight Tools at

the number on the cover of this manual as

soon as possible.

Table A

SYMBOLOGY UNPACKING

Page 7SKU 91797 For technical questions, please call 1-800-444-3353

OPERATING INSTRUCTIONS

1. Place the Fireplace Heater in the desired location for operation.

This place must be away from curtains and any other ﬂammable material. If an

extension cord is used, it must be of the appropriate size (See page 6.). The electrical

outlet must be at least a 15 amp circuit.

2. Press the Fan Switch up to turn it on. (See Figure C below.)

3. Press the 750W Switch to enable medium heat. Press the second 750W Switch to

enable maximum heat.

4. Adjust the Temperature Thermostat Knob to the desired temperature (clockwise is

maximum).

When the unit reaches the desired temperature, the unit automatically shuts off.

When the room temperature cools down, the unit will automatically turn on.

Note: The Remote Control can be used to turn the unit on and off, and to adjust the

temperature.

5. Press the Fire Switch to turn on the ﬁre lights inside the imitation logs.

Turn the Brightness Knob to the desired light level (clockwise is maximum).

6. When ﬁnished using the Fireplace Heater, press all switches down to the off position,

and unplug the line cord from the electrical outlet.

Figure C Control Panel

INSPECTION, MAINTENANCE AND CLEANING

WARNING! Make sure that all Switches of the Fireplace Heater are in the “OFF”

position and that the unit is unplugged from its electrical outlet before performing any

inspection, maintenance, or cleaning procedures.

1. Before each use, inspect the general condition of the Fireplace Heater. Check for

Fan 750W 750W Fire Lights

Temperature Thermostat Knob Brightness Knob

Page 8SKU 91797 For technical questions, please call 1-800-444-3353

loose screws, misalignment or binding of moving parts, cracked or broken parts,

damaged electrical wiring, and any other condition that may affect its safe operation.

Do not use damaged equipment.

2. Periodically recheck all nuts, bolts, and screws for tightness.

3. Store in a clean and dry location.

4. Open the Fireplace Heater door and clean the rear mirror when it becomes dirty. Wipe

the unit with a clean cloth when it becomes dusty.

5. To replace one or both of the ﬁre light bulbs:

• Remove two screws in front of the (plastic) logs, then remove the metal grate.

• Squeezethelogbasewithyourhandtoremovethebacktabsfromthebase,thenliftthe

logs enough to get your hand in. Unscrew the old bulb and replace with a new candelabra

40W bulb.

• Replace the logs to their original position, replace the metal grate and secure with the two

screws.

Figure D Fire Light Bulb Replacement

Screws

Grate

Logs

Light Bulbs

Page 9SKU 91797 For technical questions, please call 1-800-444-3353

Part Description Qty.

1 Pin 2

2 Ring 2

3 Hinge 2

4 MDF Housing 1

5 Window for receiver 1

6 Switch Box 1

7 Thermostat 1

8 Front Board 1

9 Press Board for glass 1

10 Diffuser 1

11 Right Angle Holder 2

12 Flame Board 1

13 Pot Hook for Ribbon 14

14 Ribbon 7

15 Reﬂecting paper 1

16 Rubber Stripe 2

17 Glass Stand 2

18 Rivet 14

19 Back Piece for Flame 1

20 Blower Housing 2

21 Side Sheet for Blower 1

22 Warder 1

23 Board 1

24 Blower Housing 1

25 Foot 4

26 Top Cover 1

27 Terminal Fuse 1

28 Remote Control 1

29 Switch 2

30 Plastic Tie -

31 Boat Switch 4

32 Screw 4

33 Receiver 1

34 Back Board 1

35 Light Strainer 1

36 Quakeproof Ring 4

37 Holder for Front Board 1

Part Description Qty.

38 Clip 3

39 Screw for Glass 3

40 Door Glass 1

41 Door Frame 1

42 Log 2

43 Log Bed 1

44 Door Handle 1

45 Grenade of the Handle 1

46 Motor 2

47 Bulb Holder 2

48 Handrail 1

49 Magnet 2

50 Bottom Board for Flame 1

51 Knob 1

52 Screw Cap 2

53 Bulb Holder 2

54 Bulb 2

55 Side-sheet 2

56 Heating Element 1

57 Switch for ﬁre adjust 1

58 Gasket 1

59 Bolt -

60 Clip 6

61 Press Clip 4

62 Glass-stripe 1

63 Cover 20

64 Connector 20

65 Connection Pole 1

66 Components for Fire Adjustment 1

67 Rubber Ring 2

68 Internal Wires -

69 Metal Holder 1

70 Screw 12

71 Blower 2

72 Wire Clip 1

73 Wire 1

PARTS LIST

Page 10SKU 91797 For technical questions, please call 1-800-444-3353

NOTE: Some parts are listed and shown for illustration purposes only and are not available

individually as replacement parts.

ASSEMBLY DRAWING

REV 10d

Andere Handbücher für 91797

Inhaltsverzeichnis

Andere Chicago Electric Kamin im Innenbereich Handbücher

Chicago Electric

Chicago Electric 91797 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch