Chicago Electric 66738 Installationshandbuch

CARPET HEAT BOND

SEAMING IRON

Model

66738

SET UP AND OPERATING INSTRUCTIONS

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Cover Revised 09l

SKU 66738 For technical questions, please call 1-800-444-3353. Page 2

SAVE THIS MANUAL

Keep this manual for the safety warn-

ings and precautions, assembly, operat-

ing, inspection, maintenance and cleaning

procedures. Write the product’s serial

number in the back of the manual near the

assembly diagram (or month and year of

purchase if product has no number). Keep

this manual and the receipt in a safe and

dry place for future reference.

IMPORTANT SAFETY

INFORMATION

In this manual, on the labeling,

and all other information provid-

ed with this product:

This is the safety alert

symbol. It is used to alert

you to potential personal

injury hazards. Obey all

safety messages that

follow this symbol to avoid

possible injury or death.

DANGER indicates

a hazardous

situation which, if not

avoided, will result in death or

serious injury.

WARNING

indicates a

hazardous situation which, if

not avoided, could result in

death or serious injury.

CAUTION, used

with the safety

alert symbol, indicates a

hazardous situation which, if

not avoided, could result in

minor or moderate injury.

NOTICE is used to

address practices

not related to personal injury.

CAUTION, without

the safety alert

symbol, is used to address

practices not related to

personal injury.

General Tool Safety Warnings

WARNING Read all safety

warnings and instructions.

Failure to follow the warnings and

instructions may result in electric

shock, re and/or serious injury.

Save all warnings and

instructions for future reference.

Work area safety1.

Keep work area clean and well lit.a.

Cluttered or dark areas invite acci-

dents.

Do not operate tools in explosiveb.

atmospheres, such as in the pres-

ence of ammable liquids, gases

or dust. Tools create sparks which

may ignite the dust or fumes.

Keep children and bystandersc.away while operating a tool. Dis-

tractions can cause you to lose con-

trol.

Electrical safety2.

Tool plugs must match the outlet.a.

Never modify the plug in any way.

Do not use any adapter plugs with

grounded tools. Unmodied plugs

and matching outlets will reduce risk

of electric shock.

Avoid body contact with groundedb.

surfaces such as pipes, radiators,

ranges and refrigerators. There is

SKU 66738 For technical questions, please call 1-800-444-3353. Page 3

an increased risk of electric shock if

your body is grounded.

Do not expose tools to rain or wetc.conditions. Water entering a tool

will increase the risk of electric shock.

Do not abuse the cord. Never used.

the cord for carrying, pulling or

unplugging the tool. Keep cord

away from heat, oil, sharp edges or

moving parts. Damaged or entan-

gled cords increase the risk of electric

shock.

If operating a tool in a damp loca-e.

tion is unavoidable, use a Ground

Fault Circuit Interrupter (GFCI)

protected supply. Use of a GFCI

reduces the risk of electric shock.

Personal safety3.

Stay alert, watch what you are do-a.

ing and use common sense when

operating a tool. Do not use a

tool while you are tired or under

the inuence of drugs, alcohol or

medication. A moment of inattention

while operating tools may result in

serious personal injury.

Use personal protective equip-b.

ment. Always wear eye protection.

Safety equipment such as fresh air

mask, non-skid safety shoes, hard

hat, or hearing protection used for

appropriate conditions will reduce

personal injuries.

Do not overreach. Keep properc.footing and balance at all times.

This enables better control of the tool

in unexpected situations.

Only use safety equipment thatd.

has been approved by an appropri-

ate standards agency. Unapproved

safety equipment may not provide

adequate protection. Eye protection

must be ANSI-approved and breath-

ing protection must be NIOSH-ap-

proved for the specic hazards in the

work area.

Tool use and care4.

Do not force the tool. Use thea.

correct tool for your application.

The correct tool will do the job better

and safer at the rate for which it was

designed.

Disconnect the plug from the pow-b.

er source and allow to cool before

making any adjustments, changing

accessories, or storing this tool.

Such preventive safety measures

reduce the risk of damage or injury.

Store idle tools out of the reach ofc.children and do not allow persons

unfamiliar with this tool or these

instructions to operate the tool.

Tools are dangerous in the hands of

untrained users.

Maintain tools. Check for mis-d.

alignment or breakage of parts and

any other condition that may affect

the tool’s operation. If damaged,

have the tool repaired before use.

Many accidents are caused by poorly

maintained tools.

Service5.

Have your tool serviced by a quali-a.

ed repair person using only iden-

tical replacement parts. This will

ensure that the safety of the tool is

maintained.

Safety Warnings

Maintain labels and nameplates on1. the tool. These carry important safety

information. If unreadable or miss-

SKU 66738 For technical questions, please call 1-800-444-3353. Page 4

ing, contact Harbor Freight Tools for a

replacement.

Place securely on Iron Holder (6)2. when not in use.

Keep away from ammable objects. 3.

Do not overheat adhesive.4.

When using a handheld tool, maintain5.

a rm, controlling grip on the tool.

Do not leave the tool unattended6. when it is plugged into an electrical

outlet. Unplug the tool from its elec-

trical outlet and allow to cool down

before leaving.

This product is not a toy. Keep it out7. of reach of children.

Any power cord must be properly8. grounded. Ground Fault Circuit Inter-

rupter (GFCI) should also be imple-

mented – it prevents sustained elec-

trical shock.

WARNING: Handling the cord on9. this product will expose you to lead,

a chemical known to the State of

California to cause cancer, and birth

defects or other reproductive harm.

Wash hands after handling.

(California Health & Safety Code §

25249.5, et seq.)

The warnings, precautions, and in-10. structions discussed in this instruction

manual cannot cover all possible con-

ditions and situations that may occur.

It must be understood by the operator

that common sense and caution are

factors which cannot be built into this

product, but must be supplied by the

operator.

SAVE THESE

INSTRUCTIONS.

GROUNDING

TO PREVENT

ELECTRIC SHOCK

AND DEATH FROM

INCORRECT GROUNDING

WIRE CONNECTION:

Check with a qualied

electrician if you are in doubt

as to whether the outlet is

properly grounded. Do not

modify the power cord plug

provided with the tool. Never

remove the grounding prong

from the plug. Do not use the

tool if the power cord or plug

is damaged. If damaged, have

it repaired by a qualied

service technician before use.

If the plug will not t the

outlet, have a proper outlet

installed by a qualied

electrician.

Grounded Tools: Tools with Three

Prong Plugs

Tools marked with “Grounding Re-1. quired” have a three wire cord and

three prong grounding plug. The

plug must be connected to a properly

SKU 66738 For technical questions, please call 1-800-444-3353. Page 5

grounded outlet. If the tool should

electrically malfunction or break

down, grounding provides a low

resistance path to carry electricity

away from the user, reducing the risk

of electric shock. (See 3-Prong Plug

and Outlet.)

The grounding prong in the plug is2. connected through the green wire in-

side the cord to the grounding system

in the tool. The green wire in the cord

must be the only wire connected to

the tool’s grounding system and must

never be attached to an electrically

“live” terminal. (See 3-Prong Plug

and Outlet.)

The tool must be plugged into an3. appropriate outlet, properly installed

and grounded in accordance with all

codes and ordinances. The plug and

outlet should look like those in the

preceding illustration. (See 3-Prong

Plug and Outlet.)

Extension Cords

Grounded1. tools require a three wire

extension cord. Double Insulated

tools can use either a two or three

wire extension cord.

As the distance from the supply outlet2. increases, you must use a heavier

gauge extension cord. Using exten-

sion cords with inadequately sized

wire causes a serious drop in voltage,

resulting in loss of power and pos-

sible tool damage.

(See Table A.)

The smaller the gauge number of the3. wire, the greater the capacity of the

cord. For example, a 14 gauge cord

can carry a higher current than a 16

gauge cord. (See Table A.)

When using more than one exten-4. sion cord to make up the total length,

make sure each cord contains at

least the minimum wire size required.

(See Table A.)

If you are using one extension cord5. for more than one tool, add the

nameplate amperes and use the sum

to determine the required minimum

cord size. (See Table A.)

If you are using an extension cord6. outdoors, make sure it is marked with

the sufx “W-A” (“W” in Canada) to

indicate it is acceptable for outdoor

use.

Make sure the extension cord is prop-7. erly wired and in good electrical con-

dition. Always replace a damaged

extension cord or have it repaired by

a qualied electrician before using it.

Protect the extension cords from8. sharp objects, excessive heat, and

damp or wet areas.

RECOMMENDED MINIMUM WIRE

GAUGE FOR EXTENSION CORDS*

(120/240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25’

50’

75’

100’

150’

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

TABLE A * Based on limiting the line

voltage drop to ve volts at

150% of the rated amperes.

SKU 66738 For technical questions, please call 1-800-444-3353. Page 6

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~ Volts Alternating Current

AAmperes

n0xxxx/min. No Load Revolutions per Minute

(RPM)

SKU 66738 For technical questions, please call 1-800-444-3353. Page 7

SPECIFICATIONS

Electrical Requirements 120 V~, 800 W

Power Cord 112" L, 3-Prong

Grounded

Temperature Range 147° - 442° F

Temperature Setting

Heat

Setting Temperature

Range F Time to Reach

1 147° - 190° 2 Minutes

2 230° - 298° 3 Minutes

3 311° - 379° 3.5 Minutes

4 374° - 442° 4 Minutes

UNPACKING

When unpacking, make sure that the

item is intact and undamaged. If any parts

are missing or broken, please call Harbor

Freight Tools at 1-800-444-3353 as soon

as possible.

OPERATING INSTRUCTIONS

Read the ENTIRE IMPORTANT

SAFETY INFORMATION

section at the beginning of this

manual including all text under

subheadings therein before set

up or use of this product.

Work Piece and Work Area Set Up

Designate a work area that is clean1. and well-lit. The work area must not

allow access by children or pets to

prevent injury and distraction.

Route the power cord along a safe2. route to reach the work area without

creating a tripping hazard or exposing

the power cord to possible damage.

The power cord must reach the work

area with enough extra length to al-

low free movement while working.

There must not be hazardous ob-3. jects, such as utility lines or foreign

objects, nearby that will present a

hazard while working.

General Operating Instructions

Place the Iron Holder (6) on a at, 1.

level, non-ammable surface.

Wear ANSI-approved safety goggles2. and heavy-duty work gloves during

use. Forced-air ventilation may be

required depending on the type of

glue being heated.

Turn the Heat Control Knob (8) to the3. “OFF” position.

Place the Iron securely into the Iron4. Holder.

Turn the Heat Control Knob to the5. setting desired and wait until the Iron

SKU 66738 For technical questions, please call 1-800-444-3353. Page 8

reaches the desired temperature.

(See Temperature Setting chart.)

Consult the adhesive tape manu-

facturer’s instruction for proper heat

range.

Avoid touching the Heat Shield (9)6. and Bottom Sole Plate (5) while

plugged in and hot.

Try the Iron on a scrap piece of adhe-7. sive tape to test for desired tempera-

ture result.

To prevent accidents, turn off the tool8. and disconnect its power supply after

use. Allow to cool completely, then

clean and store the tool indoors out of

children’s reach.

SKU 66738 For technical questions, please call 1-800-444-3353. Page 9

MAINTENANCE AND

SERVICING

Procedures not specically

explained in this manual

must be performed only by a

qualied technician.

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL

OPERATION:

Turn the Calibration Knob of

the tool to its “OFF” position

and unplug the tool from its

electrical outlet before

performing any inspection,

maintenance, or cleaning

procedures.

Cleaning and Maintenance

BEFORE EACH USE,1. inspect the

general condition of the tool. Check

for loose screws, misalignment or

binding of moving parts, cracked or

broken parts, damaged electrical wir-

ing, and any other condition that may

affect its safe operation.

AFTER USE,2. clean Bottom Sole

Plate (5) of any glue or adhesive that

may have transferred on by rubbing

on a clean scrap of carpeting while

still hot.

Place back on Iron Holder when not3. in use.

4. WARNING! If the supply cord of

this tool is damaged, it must be re-

placed only by a qualied service

technician.

SKU 66738 For technical questions, please call 1-800-444-3353. Page 10

Troubleshooting

Problem Possible Causes Likely Solutions

Tool will not heat

No power at outlet.1.

Cord not connected.2.

Heat Control Knob in OFF3. position.

Check power at outlet.1.

Check that cord is plugged in.2.

Turn Heat Control Knob to a heat setting3. position.

Follow all safety precautions whenever diagnosing or servicing the

tool. Disconnect power supply before service.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT

HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/

OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD

BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE

BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER

INSTALLATION OF REPLACEMENT PARTS THERETO.

PARTS LIST

Part Description

1 Handle Set w(8) Screws

2Cord Set (Relief Spring, Wire Connection

Clip, two Screws

3Thermostat w/ Extension Post for Control

Knob

4Top Sole Plate w/ve Screws

5 Bottom Sole Plate, Aluminum, Flat

6 Iron Holder

7 Internal Wire Set (2 pieces)

8 Heat Control Knob

9 Heat Shield w/2 Screws and (1) Washer

10 Gasket (Top of heat shield for Handle

Mount)

11 Gasket (Between Heat Shield for top of

Sole Plate)

12 Heating Element

Inhaltsverzeichnis

Andere Chicago Electric Eisen Handbücher

Chicago Electric

Chicago Electric 94627 Bedienungsanleitung

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Philips

Philips GC6012 Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Texi

Texi Hestia Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Philips

Philips HI5914/30 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Scarlett

Scarlett SC-1334S Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Philips

Philips GC651 Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

Philips

Philips GC800 Bedienungsanleitung