Chicago Electric 61423 Bedienungsanleitung

Page 2 For technical questions, please call 1-800-444-3353. Item 61423

SAFETY OPERATION MAINTENANCESETUP

Table of Contents

Safety .................................................2

Specifications .....................................8

Setup ..................................................8

Operation............................................9

Maintenance......................................10

Parts List and Diagram......................11

Warranty ............................................12

WARNING SYMBOLS AND DEFINITIONS

This is the safety alert symbol. It is used to alert you to

potential personal injury hazards. Obey all safety messages

that follow this symbol to avoid possible injury or death.

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Addresses practices not related to personal injury.

IMPORTANT SAFETY INFORMATION

General Power Tool Safety Warnings

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term ″power tool″ in the warnings refers to your mains-operated (corded) power tool.

Work area safety

1. Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence

of flammable liquids, gases or dust.

Power tools create sparks which

may ignite the dust or fumes.

3. Keep children and bystanders

away while operating a power tool.

Distractions can cause you to lose control.

Page 3For technical questions, please call 1-800-444-3353.Item 61423

SAFETYOPERATIONMAINTENANCE SETUP

Electrical safety

1. Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs

with grounded power tools.

Unmodified plugs and matching outlets

will reduce risk of electric shock.

2. Avoid body contact with grounded

surfaces such as pipes, radiators, ranges

and refrigerators. There is an increased

risk of electric shock if your body is grounded.

3. Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric shock.

4. Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase

the risk of electric shock.

5. When operating a power tool

outdoors, use an extension

cord suitable for outdoor use.

Use of a cord suitable for outdoor use

reduces the risk of electric shock.

6. If operating a power tool in a damp

location is unavoidable, use a

Ground Fault Circuit Interrupter

(GFCI) protected supply. Use of a GFCI

reduces the risk of electric shock.

Personal safety

1. Stay alert, watch what you are

doing and use common sense when

operating a power tool. Do not use

a power tool while you are tired or

under the influence of drugs, alcohol

or medication. A moment of inattention

while operating power tools may

result in serious personal injury.

2. Use personal protective equipment.

Always wear eye protection.

Safety equipment such as dust mask,

non-skid safety shoes, hard hat, or

hearing protection used for appropriate

conditions will reduce personal injuries.

3. Prevent unintentional starting.

Ensure the Trigger is in the off-position

before connecting to power source,

picking up or carrying the tool.

Carrying power tools with your finger on

the Trigger or energizing power tools that

have the Trigger on invites accidents.

4. Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the

power tool in unexpected situations.

5. Dress properly. Do not wear loose

clothing or jewelry. Keep your

hair, clothing and gloves away

from moving parts. Loose clothes, jewelry

or long hair can be caught in moving parts.

6. Only use safety equipment that has

been approved by an appropriate

standards agency. Unapproved safety

equipment may not provide adequate

protection. Eye protection must be

ANSI-approved and breathing protection

must be NIOSH-approved for the

specific hazards in the work area.

Page 4 For technical questions, please call 1-800-444-3353. Item 61423

SAFETY OPERATION MAINTENANCESETUP

Power tool use and care

1. Do not force the power tool.

Use the correct power tool for your

application. The correct power tool

will do the job better and safer at the

rate for which it was designed.

2. Do not use the power tool if the

Trigger does not turn it on and off.

Any power tool that cannot be

controlled with the Trigger is

dangerous and must be repaired.

3. Disconnect the plug from the power

source before making any adjustments,

changing accessories, or storing

power tools. Such preventive safety

measures reduce the risk of starting

the power tool accidentally.

4. Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the

hands of untrained users.

5. Maintain power tools. Check for

misalignment or binding of moving

parts, breakage of parts and any other

condition that may affect the power tool’s

operation. If damaged, have the power

tool repaired before use. Many accidents

are caused by poorly maintained power tools.

6. Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to

be performed. Use of the power tool for

operations different from those intended

could result in a hazardous situation.

Service

Have your power tool serviced by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Page 5For technical questions, please call 1-800-444-3353.Item 61423

SAFETYOPERATIONMAINTENANCE SETUP

Hot Knife Safety Warnings

1. This Hot Knife can create heat up to

approximately 840° Fahrenheit. Always

keep fingers, hands, body, and clothing away

from the heated components of this tool.

2. Do not allow any objects (liquid or

metal) to fall into the Heat Block holes

of the tool. Doing so can cause a

short circuit and/or electric shock.

3. Do not lay the Hot Knife down on a

flammable surface. Use and lay this

tool on a fireproof work surface only.

4. Keep multiple class ABC fire

extinguishers nearby.

5. Use the Hot Knife in a well

ventilated area only.

6. Allow the Hot Knife to completely

cool before storing.

7. Maintain labels and nameplates on the tool.

These carry important safety information.

If unreadable or missing, contact

Harbor Freight Tools for a replacement.

8. Avoid unintentional starting. Prepare to

begin work before turning on the tool.

9. Do not leave the tool unattended when

it is plugged into an electrical outlet.

Turn off the tool, and unplug it from

its electrical outlet before leaving.

10. This product is not a toy.

Keep it out of reach of children.

11. People with pacemakers should consult their

physician(s) before use. Electromagnetic

fields in close proximity to heart pacemaker

could cause pacemaker interference or

pacemaker failure. In addition, people with

pacemakers should:

• Avoid operating alone.

• Properly maintain and inspect

to avoid electrical shock.

• Properly ground power cord.

Ground Fault Circuit Interrupter (GFCI)

should also be implemented –

it prevents sustained electrical shock.

12. WARNING: This product contains or,

when used, produces a chemical known to

the State of California to cause cancer and

birth defects or other reproductive harm.

(California Health & Safety Code

§ 25249.5, et seq.)

13. WARNING: Handling the cord on this product

will expose you to lead, a chemical known

to the State of California to cause cancer,

and birth defects or other reproductive harm.

Wash hands after handling.

(California Health & Safety Code

§ 25249.5, et seq.)

14. The warnings, precautions, and instructions

discussed in this instruction manual cannot

cover all possible conditions and situations

that may occur. It must be understood by the

operator that common sense and caution are

factors which cannot be built into this product,

but must be supplied by the operator.

SAVE THESE INSTRUCTIONS.

Page 6 For technical questions, please call 1-800-444-3353. Item 61423

SAFETY OPERATION MAINTENANCESETUP

Grounding

TO PREVENT ELECTRIC SHOCK AND DEATH FROM

INCORRECT GROUNDING WIRE CONNECTION:

Check with a qualified electrician if you are in doubt as to whether the outlet is

properly grounded. Do not modify the power cord plug provided with the tool.

Never remove the grounding prong from the plug. Do not use the tool if the power cord or

plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will

not fit the outlet, have a proper outlet installed by a qualified electrician.

Grounded Tools: Tools with Three Prong Plugs

3-Prong Plug and Outlet

1. Tools marked with “Grounding Required”

have a three wire cord and three prong

grounding plug. The plug must be connected

to a properly grounded outlet. If the tool

should electrically malfunction or break

down, grounding provides a low resistance

path to carry electricity away from the

user, reducing the risk of electric shock.

2. The grounding prong in the plug is

connected through the green wire inside

the cord to the grounding system in

the tool. The green wire in the cord must

be the only wire connected to the tool’s

grounding system and must never be

attached to an electrically “live” terminal.

3. The tool must be plugged into an appropriate

outlet, properly installed and grounded in

accordance with all codes and ordinances.

The plug and outlet should look like those in

the preceding illustration.

(See 3-Prong Plug and Outlet.)

Page 7For technical questions, please call 1-800-444-3353.Item 61423

SAFETYOPERATIONMAINTENANCE SETUP

Extension Cords

1. Grounded tools require a

three wire extension cord.

Double Insulated tools can use either

a two or three wire extension cord.

2. As the distance from the supply outlet

increases, you must use a heavier gauge

extension cord. Using extension cords with

inadequately sized wire causes a serious

drop in voltage, resulting in loss of power

and possible tool damage. (See Table A.)

3. The smaller the gauge number of

the wire, the greater the capacity of

the cord. For example, a 14 gauge

cord can carry a higher current than

a 16 gauge cord. (See Table A.)

4. When using more than one extension cord

to make up the total length, make sure

each cord contains at least the minimum

wire size required. (See Table A.)

5. If you are using one extension cord for more

than one tool, add the nameplate amperes

and use the sum to determine the required

minimum cord size. (See Table A.)

6. If you are using an extension cord

outdoors, make sure it is marked with the

suffix “W-A” (“W” in Canada) to indicate

it is acceptable for outdoor use.

7. Make sure the extension cord is properly

wired and in good electrical condition.

Always replace a damaged extension

cord or have it repaired by a qualified

electrician before using it.

8. Protect the extension cords from

sharp objects, excessive heat,

and damp or wet areas.

Table A: Recommended Minimum

Wire Gauge for Extension Cords*

(120/240 Volt)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25´

50´

75´

100´

150´

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

* Based on limiting the line voltage drop to

five volts at 150% of the rated amperes.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

VVolts

~Alternating Current

AAmperes

n0xxxx/min. No Load Revolutions per Minute (RPM)

WARNING marking concerning Risk

of Eye Injury. Wear ANSI-approved

safety goggles with side shields.

Read the manual before

set-up and/or use.

WARNING marking

concerning Risk of Fire.

Do not cover ventilation ducts.

WARNING marking concerning

Risk of Electric Shock.

Maintain Power cord properly.

Page 8 For technical questions, please call 1-800-444-3353. Item 61423

SAFETY OPERATION MAINTENANCESETUP

Specifications

Electrical Rating 120V~ / 60Hz / 130W

Cutting Depth 3-3/4″ (with Depth Scale)

5-7/16″ (without Depth Scale)

Maximum Temperature 840° F

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section

at the beginning of this manual including all text under

subheadings therein before set up or use of this product.

Functions

Trigger

Acorn

Nut

Temperature

Knob

Power

LED

Blade

Depth

Scale

Depth

Bracket

Scale

Screw

3115903

Page 9For technical questions, please call 1-800-444-3353.Item 61423

SAFETYOPERATIONMAINTENANCE SETUP

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section

at the beginning of this manual including all text under

subheadings therein before set up or use of this product.

TOOL SET UP - Cutting Depth

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Release the Trigger, unplug the tool from its electrical outlet, and

allow it to cool completely before adjusting tool or installing accessories.

1. For greatest cutting depth, do not attach

the Depth Bracket. To limit cutting depth,

follow the directions below.

2. Remove the Acorn Nuts from

the front of the Handle.

3. Place the Depth Bracket over

the Blade and the protruding Bolts.

4. Secure the Depth Bracket with

the two Acorn Nuts.

5. Loosen the two Scale Screws.

6. Adjust the Depth Scale to the desired cutting

depth and tighten the two Scale Screws.

Workpiece and Work Area Set Up

1. Designate a well-ventilated work area

that is clean and well-lit. The work area

must not allow access by children or

pets to prevent distraction and injury.

2. Route the power cord along a safe route

to reach the work area without creating a

tripping hazard or exposing the power cord

to possible damage. The power cord must

reach the work area with enough extra length

to allow free movement while working.

3. Use on a non-flammable surface only.

4. Have multiple class ABC fire

extinguishers nearby.

5. Secure loose workpieces using a

vise or clamps (not included) to

prevent movement while working.

6. There must not be objects,

such as utility lines or flammable objects,

nearby that will present

a hazard while working.

General Operating Instructions

1. Plug the Power Cord into the nearest

120 volt, grounded, electrical outlet.

2. Turn the Temperature Knob to

the desired temperature.

3. Press and hold the Trigger to heat up the

Blade. The Blade will reach the operating

temperature in about one minute and will

remain at the temperature selected.

4. When the Blade has reached the pre-set

temperature, you may use the sharp edge

of the Blade for line cutting or use the side

of the Blade for wide groove cutting.

5. When the Trigger is released, power

to the Blade is cut off and the Blade

will cool down gradually.

CAUTION! The residual heat on the

Blade takes several minutes to dissipate.

Use caution while the Blade is still hot.

6. To prevent accidents, turn off the tool and

disconnect its power supply after use.

Allow to cool completely on a non-flammable

surface out of children’s reach after use.

Clean, then store the tool indoors

out of children’s reach.

Page 10 For technical questions, please call 1-800-444-3353. Item 61423

SAFETY OPERATION MAINTENANCESETUP

Maintenance and Servicing

Procedures not specifically explained in this manual must

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Release the Trigger, unplug the tool from its electrical outlet, and

allow it to cool completely before adjusting tool or installing accessories.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:

Do not use damaged equipment. If abnormal noise or vibration

occurs, have the problem corrected before further use.

Cleaning and Maintenance

1. BEFORE EACH USE, inspect the general

condition of the tool. Check for:

• loose hardware,

• cracked or broken parts,

• damaged electrical wiring, and

• any other condition that may

affect its safe operation.

2. AFTER USE, wipe external surfaces

of the tool with clean cloth.

3. WARNING! If the supply cord

of this power tool is damaged,

it must be replaced only by a

qualified service technician.

Troubleshooting

Problem Possible Cause Possible Solution

Hot Knife will not turn on. 1. No power at electrical outlet.

2. Trigger not pressed.

1. Check power at outlet.

2. Press and hold Trigger.

Hot Knife does not maintain

pre-selected heat temperature

during operation.

Trigger not pressed and held. Press and hold Trigger

throughout operation.

Follow all safety precautions whenever diagnosing or servicing the tool.

Disconnect power supply before service.

Record Product’s Serial Number Here:

Note: If product has no serial number,

record month and year of purchase instead.

Note: Some parts are listed and shown

for illustration purposes only, and are not

available individually as replacement parts.

Inhaltsverzeichnis

Andere Chicago Electric Elektrowerkzeuge Handbücher

Chicago Electric

Chicago Electric 37793 Bedienungsanleitung

Chicago Electric

Chicago Electric 96289 Installationshandbuch

Chicago Electric

Chicago Electric 69343 Montageanleitung

Chicago Electric

Chicago Electric 67537 Bedienungsanleitung

Chicago Electric

Chicago Electric 68221 Bedienungsanleitung

Chicago Electric

Chicago Electric 57226 Montageanleitung

Chicago Electric

Chicago Electric 62302 Montageanleitung

Chicago Electric

Chicago Electric 68857 Montageanleitung

Chicago Electric

Chicago Electric 68848 Bedienungsanleitung

Chicago Electric

Chicago Electric 35778 Bedienungsanleitung

Chicago Electric

Chicago Electric Chicago 94560 Installationshandbuch

Chicago Electric

Chicago Electric 67845 Installationshandbuch

Chicago Electric

Chicago Electric DEMOLITION HAMMER 93853 Installationshandbuch

Chicago Electric

Chicago Electric 41053 Installationshandbuch

Chicago Electric

Chicago Electric 66508 Bedienungsanleitung

Chicago Electric

Chicago Electric 67097 Installationshandbuch

Chicago Electric

Chicago Electric 61737 Montageanleitung

Chicago Electric

Chicago Electric 35 LB Original Bedienungsanleitung

Chicago Electric

Chicago Electric 68221 Montageanleitung

Chicago Electric

Chicago Electric 42831 Bedienungsanleitung

Chicago Electric

Chicago Electric 92772 Bedienungsanleitung

Chicago Electric

Chicago Electric 68199 Bedienungsanleitung

Chicago Electric

Chicago Electric 43585 Bedienungsanleitung

Chicago Electric

Chicago Electric 90541 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch