Chicago Electric 44829 Bedienungsanleitung

14” CUT OFF SAW

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit ourWeb site at http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor FreightTools.

For technical questions and replacement parts, please call 1-800-444-3353

Model 44829

(Blade Sold Separately)

You will need the manual for the safety warnings and precautions, assembly

instructions, operating and maintenance procedures, parts list and diagram. Keep

your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep the manual and invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be fol-

lowed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

1. Avoid working alone. If an accident happens, an assistant can bring help.

2. Keep work area clean. Cluttered areas invite injuries.

3. Observe work area conditions. Don’t expose to rain. Keep work area well

lighted.

4. Keep children away. Children must never be allowed in the work area. Do

not let them handle machines, tools, or extension cords.

5. Store idle equipment. When not in use, tools must be stored in a dry

location to inhibit rust. Always lock up tools and keep out of reach of

children.

SKU 44829 Page 2 REV 09/01 REV 11/01

Motor 120V Single Phase 60HZ 2HP

Watts (input) 1500 Approx.

Rpms 3400

Blade Size 14” (Not Included) 1” Arbor

Miter Angle 0-45 Degrees Rt. 0-30 Left

Weight 35.6 Lbs.

Base Dimensions 18-1/2” x 10-1/2”

Cutting Capacity Up to 4”

Table Size 9-3/4” x 10-1/4”

SaveThis Manual

Specifications

Vise Assembly and SpannerWrench Included.

Recommend using #525 Cut-off Wheel (not included), 14” Diameter, 1/8”Thick-

ness, 30 Grit. This is an aluminum oxide wheel designed for general purpose

usage. For cutting masonry, recommend #44815 Cut-off Wheel (not included),

14”, 1/8”Thickness.

6. Dress properly. Do not wear loose clothing or jewelry as they can be caught

in moving parts. Protective, electrically nonconductive clothes and nonskid

footwear are recommended when working. Wear restrictive hair covering to

contain long hair.

7. Use eye and ear protection. Always wear ANSI approved impact safety

goggles. Wear an ANSI approved face shield when producing metal filings.

8. Do not overreach. Keep proper footing and balance at all times.Do not

reach over or across electrical cables or frames.

9. Maintain tools with care. Inspect tool cords periodically and, if damaged,

have them repaired by an authorized technician.

10. Use the right tool for the job. Do not attempt to force a small tool or

attachment to do the work of a larger industrial tool.There are certain

applications for which this tool was designed.Do not modify this tool and do

not use this tool for a purpose for which it was not intended.

11. Stay alert. Watch what you are doing, use common sense.Do not operate

any tool when you are tired.

12. Check for damaged parts. Before using any tool, any part that appears

damaged should be carefully checked to determine that it will operate

properly and perform its intended function.Check for alignment and binding

of moving parts; any broken parts or mounting fixtures; and any other

condition that may affect proper operation.Any part that is damaged should

be properly repaired or replaced by a qualified technician.Do not use the tool

if any switch does not turn On and Off properly.

13. Replacement parts and accessories. When servicing, use only identical

replacement parts.Use of any other parts will void the warranty. Only use

accessories intended for use with this tool.Approved accessories are

available from Harbor FreightTools.

14. Do not operate tool if under the influence of alcohol or drugs. Read

warning labels on prescriptions to determine if your judgment or reflexes are

impaired while taking drugs.If there is any doubt, do not operate the tool.

15. Use proper size and type extension cord.If an extension cord is required,

it must be of the proper size and type to supply the correct current to the

tool. Otherwise, the extension cord could melt and catch fire, or cause

electrical damage to the tool.This tool requires use of an extension cord of 0

to 12 amps capability (up to 50 feet), with wire size rated at 14 AWG.Longer

extension cords require larger size wire.If you are using the tool outdoors,

use an extension cord rated for outdoor use.(signified by “WA” on the jacket).

16. Maintenance. For your safety, maintenance should be performed regularly

by a qualified technician.

Note: Performance of this tool (if powered by line voltage) may vary depending on

variations in local line voltage. Extension cord usage may also affect tool perfor-

mance.

SKU 44829 Page 3

SKU 44829 Page 4 REV 04/02

Warning:The warnings, cautions, and instructions discussed in this instruc-

tion manual cannot cover all possible conditions and situations that may oc-

cur. It must be understood by the operator that common sense and caution

are factors which cannot be built into this product, but must be supplied by

the operator.

Unpacking

When unpacking, check to make sure the parts listed on page 6 are included.

If any parts are missing or broken,please call Harbor FreightTools at the num-

ber on the cover of this manual.

Operation

Note: Steel Capacity Cutting Chart found on page 5 of this manual.

Warning: This Cut-Off Saw is designed to cut iron metal. Do not cut wood, brick,

aluminum, or magnesium; tool damage and/or personal injury could occur.

Before using the saw always check the following:

A. Make sure the blade (not included) is securely attached.

Loosen Screw (#110) and lift Small Cover (#109) out of the way.

Warning! Unplug the power cord while setting up the saw and workpiece. Do not

plug in until ready to cut.

Using the Wrench (#91), remove the Hex Screw (#23) - reverse thread, Stop

Washer (#22), FlatWasher #21), and the Flange (#20). Set the blade on the

arbor and replace the hardware.Do not overtighten. Move Small Cover (#109)

back in place and tighten Screw (#110).

B. Check that the Upper Shield (#12) and Lower Shield (#30) are in place.

C. The Cut Off Saw must be located on a level, flat, workbench that is solid and

able to support the weight of the tool and workpieces. The workpiece must be

secured in a vise or with clamps (vise assembly included).

D. Always wear ANSI approved impact safety goggles.

1. Disconnect the Chain (#72), allowing the blade assembly to lift. The chain is

only used for transporting the tool. Make sure the saw has cooled for 3-5 minutes

before latching or unlatching the Chain (#72), to avoid burning yourself on the hot

blade.

2. Loosen the Vise (#82) on the vise assembly and position workpiece.Tighten

the Vise (#82).

3. Make sure the blade is clear to rotate freely.

4. Press the power Switch (#33). Allow blade to reach full speed.

5. Lower the Handle (#35) slowly and contact the workpiece with very little

pressure. Let the blade do the work. If the blade begins to slow, back off as you

are exerting too much pressure.

Caution: The Lower Shield (#30) and Small Cover (#109) must always be in

place. Both of these blade guards must be in place when the tool is being used.

6. Turn off the power and unplug the tool before removing workpiece. Never leave

the tool running unattended.

SKU 44829 Page 5 REV 04/02

PLEASE READTHE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM

IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER

NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO

THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE

PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE

PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY

STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN

BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BYTHE BUYER.THE BUYER

ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS

OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Maintenance

Warning! Remove the electrical plug from the outlet before maintaining the Saw.

1. Wearing gloves, carefully clean any excess metal filings that accumulate on

the saw, vise assembly, or motor housing.

2. To keep looking like new, use an automotive wax to polish the metal

Base (#87).

3. Check blade for wear, replace at the first sign of any tears or cracks.

4. Periodically check power cord for wear or tears.If necessary, have a qualified

technician replace it.

5. Never use chemicals or solvents to clean the Saw.

Lubrication

1. The motor bearings are permanently lubricated at the factory. Do not attempt to

work on the motor; the tool should be serviced by a qualified technician.

2. Any mechanical part including a pivot or threaded rod may be lightly sprayed

with a silicone or graphite lubricant, which will not hold or collect the metal filings

left from a job.

3. Every 500 Hrs. replace the Carbon Brush (#67). Remove the

Brush Cap (#68) and take out the Carbon Brush (#67).Replace and tighten the

Brush Cap (#68).

Steel Cutting Capacities

Steel Pipe - 4” Dia. x 1/4” Wall Thickness

Angle Iron - 4” x 4” x 1/2” Thickness

Solid Steel - 1-1/2” Dia.

each bolt and align the scale to your desired angle. Tighten the bolts. Carefully

set the workpiece into the Vise (#82) without disturbing the setting.

Note: Use an aluminum oxide wheel for

cutting ferrous material, i.e. angle iron,

conduit pipe, etc. Use masonry wheels to

cut masonry, stone, brick, aggregate, etc.

Miter Cuts

For Miter Cuts, you must use the Vise (#82). TheVise Stop has a

Fixed Splint (#100) for this purpose. Loosen the Vise Stop by slightly loosening

SKU 44829 Page 6 REV 04/02

Parts List

SKU 44829 Page 7 REV 04/02

NOTE: Some parts are listed and shown for illustration purposes only and are not

available individually as replacement parts.

Assembly Drawing

Inhaltsverzeichnis

Andere Chicago Electric Gesehen Handbücher

Chicago Electric

Chicago Electric 91482 Bedienungsanleitung

Chicago Electric

Chicago Electric 42818 Bedienungsanleitung

Chicago Electric

Chicago Electric 61970 Montageanleitung

Chicago Electric

Chicago Electric 61884 Montageanleitung

Chicago Electric

Chicago Electric 42933 Bedienungsanleitung

Chicago Electric

Chicago Electric 69067 Montageanleitung

Chicago Electric

Chicago Electric 56708 Montageanleitung

Chicago Electric

Chicago Electric 69480 Montageanleitung

Chicago Electric

Chicago Electric Double Cut Saw 68316 Montageanleitung

Chicago Electric

Chicago Electric 69275 Montageanleitung

Chicago Electric

Chicago Electric 8897 Bedienungsanleitung

Chicago Electric

Chicago Electric 62800 Montageanleitung

Chicago Electric

Chicago Electric 97580 Installationshandbuch

Chicago Electric

Chicago Electric 98089 Installationshandbuch

Chicago Electric

Chicago Electric 61481 Montageanleitung

Chicago Electric

Chicago Electric 47840 Montageanleitung

Chicago Electric

Chicago Electric 65298 Installationshandbuch

Chicago Electric

Chicago Electric 69078 Montageanleitung

Chicago Electric

Chicago Electric POWER TOOL 94362 Bedienungsanleitung

Chicago Electric

Chicago Electric 42597 Handbuch

Chicago Electric

Chicago Electric 14 Industrial Cut-off Saw 68104 Montageanleitung

Chicago Electric

Chicago Electric 68849 Bedienungsanleitung

Chicago Electric

Chicago Electric 3733 Bedienungsanleitung

Chicago Electric

Chicago Electric 69683 Montageanleitung

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung