Chicago Electric CAMARILLO 93255 Bedienungsanleitung

SPOTLIGHT

10 MILLION CANDLE POWER

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

manual or any artwork contained herein may be reproduced in any shape or form

without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

93255

Due to continuing improvements, actual product may differ slightly from the

product described herein.

REV 01/07

SKU 93255 For technical questions, please call 1-800-444-3353. Page 2

Specifications

metInoitpircseD

ecruoSrewoPhA7/CDV21,dica-daeldelaes,yrettaB

bluBthgiL,W09/001V214H

sneLrotcelferhtiwretemai

dhcni8

retpadAgnigrahCAm005/CDV51otCAV021

retpadAnoitarepO esufA01ni-tliubhtiwretpadaCDV21gulp"rethgilett

eragic"dedne-elbuoD

thgieW.sbl54.9

serutaeF ;dnatselbatsujdA;partsgniyrraC;rotacidnisutatsgnigrahC

ylppusr

ewopA01/CDV21asadesueboslanaC

Save This Manual

You will need the manual for the safety warnings and precautions, assembly

instructions, operating and maintenance procedures, parts list and diagram. Keep

your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep the manual and invoice in a safe and dry place for future reference.

Safety Warnings and Precautions

WARNING: When using tool, basic safety precautions should always be

followed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this tool!

1. Avoid eye damage. Do not shine light directly into the eyes of people or

animals. Temporary blindness can occur.

2. Avoid burns. Do not touch the Spotlight lens during operation. It becomes

very hot. Allow the Spotlight to cool down before performing any maintenance.

3. Avoid overheating the Spotlight. Do not block the lens and reflector during

operation.

4. Observe work area conditions. Do not use in damp or wet locations. Don’t

expose to rain. Do not use electrically powered tools in the presence of

flammable gases or liquids.

5. Keep children away. Children must never be allowed in the work area. Do

not let them handle machines, tools, or extension cords.

6. Store idle equipment. When not in use, tools must be stored in a dry location

to inhibit corrosion.

REV 01/07

SKU 93255 For technical questions, please call 1-800-444-3353. Page 3

7. Use the right tool for the job. Do not attempt to force a small tool or attachment

to do the work of a larger industrial tool. There are certain applications for

which this tool was designed. It will do the job better and more safely at the

rate for which it was intended. Do not modify this tool and do not use this tool

for a purpose for which it was not intended.

8. Maintenance. For your safety, service and maintenance should be performed

by a qualified technician as a high voltage hazard exists within the unit circuitry.

Battery replacement is not hazardous, however.

9. Check for damaged parts. Before using any tool, any part that appears

damaged should be carefully checked to determine that it will operate properly

and perform its intended function. Do not use if any parts are broken; or any

other condition that may affect proper operation. Any part that is damaged

should be properly repaired or replaced by a qualified technician. Do not use

the tool if any switch does not turn On and Off properly.

10. Replacement parts and accessories. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use

accessories intended for use with this tool. Approved accessories are available

from Harbor Freight Tools.

11. Grounded tools must be plugged into an outlet properly installed and

grounded in accordance with all codes and ordinances. Never remove

the grounding prong or modify the plug in any way. Check with a qualified

electrician if you are in doubt as to whether the outlet is properly grounded.

If the tools should electrically malfunction or break down, grounding provides

a low resistance path to carry electricity away from the user.

12. Avoid body contact with grounded surfaces such as pipes, radiators,

ranges, and refrigerators. There is an increased risk of electric shock if your

body is grounded.

13. Do not abuse the Adapter Power Cord. Never use the Power Cord to

carry the adapter or pull the Plug from an outlet. Keep the Power Cord

away from heat, oil, sharp edges, or moving parts. Replace damaged

Power Cords immediately. Damaged Power Cords increase the risk of electric

shock.

14. When operating a power tool outside, use an outdoor extension cord

marked “W-A” or “W”. These extension cords are rated for outdoor use, and

reduce the risk of electric shock.

Note: Performance of this Spotlight may vary depending on variations in local line

voltage while charging, or Spotlight Battery power.

SKU 93255 For technical questions, please call 1-800-444-3353. Page 4

Battery Precautions

1. Read all instructions and warnings

on the Battery before charging the

battery.

2. To avoid accidents, charge the

supplied Battery only. Use only the

supplied charging adapters for

charging the internal Battery.

3. Replace a dead Battery with only the

same type (See Specifications, page

2).

4. Do not expose the Battery to rain or

wet conditions.

5. To avoid damage of cable and plug,

never pull the cable to disconnect

the Adapter.

6. Do not use the Adapters if the cable

or plug are damaged.

7. Repairs should be carried out by a

qualified technician.

8. Do not touch the Battery poles with

any conductive source.

9. Do not store the Battery in a box with

other metal objects.

10. Do not throw the Battery in a fire or

in the general trash. Contact your

local hazardous waste disposal

authority for proper disposal.

11. Do not drain the Battery completely

before recharging. Recharge fully

when low, or quarterly when stored.

12. Always recharge the Battery when

tool performance begins to diminish.

Severe heat is most destructive to a

Battery; the more heat generated,

the faster the Battery loses power.

A Battery that gets too hot can be

Unpacking

When unpacking, check to make sure

the following parts are included. If any

parts are missing or broken, please call

Harbor Freight Tools at the number on

the cover of this manual.

Car Plug Adapter AC/DC Adapter

Shoulder

Strap

Main Unit

permanently damaged. Never over-

discharge a Battery by using the tool

even after tool performance is

decreasing.When tool performance

begins to diminish, stop the tool, and

recharge the Battery.

13. Always remove the Battery from the

Spotlight before performing

inspection, maintenance, cleaning

procedures, or storage.

Warning: The warnings, cautions, and

instructions discussed in this

instruction manual cannot cover all

possible conditions and situations

that may occur. It must be understood

by the operator that common sense

and caution are factors which cannot

be built into this product, but must be

supplied by the operator.

REV 01/07

SKU 93255 For technical questions, please call 1-800-444-3353. Page 5

Charging Battery

Caution: Set the Spotlight On/Off Switch to the Off position before charging.

Never charge the Battery for over 16 hours. Charge only until the red LED

Battery Status Indicator shuts off. Do not operate the Spotlight while charging.

1. Open the Charging Port Cover (10) and plug the AC/DC Adapter (37) into the

charging port underneath, and the other end into the 120 VAC electrical outlet.

The Charging Status Indicator turns red, indicating charging. The Battery will

charge for approximately 13-16 hours if the AC Adapter is used.

When charging is complete, the Charging Status Indicator turns off, indicating

charging is complete.

2. Unplug the Adapter from the power source and store again in the Adapter

compartment of the Spotlight. Latch the Back Cover.

Note: Never attempt to charge the Battery (25) by using the Car Plug Adapter (36).

This Adapter should only be used to power the spotlight when the battery is

out of power.

Operation

Warning: Avoid eye damage. Do not shine light directly into the eyes of people

or animals. This Spotlight emits a high intensity beam and could cause

temporary blindness if shined directly into the eyes.

1. To turn the Spotlight on, hold the Rubber Grip handle with one hand, and push

the On/Off Switch with the other. The first stop is the low setting and the

second stop is the high setting.

2. To check the battery charge status, press the Battery Status Button (34) with

the light on. Note the number of yellow LEDs that illuminate. If there are 3, the

unit is almost fully charged. If there is only one, switch the unit off and recharge

it.

3. To position the Spotlight at rest, move the Stands to the desired position.

4. To turn the Spotlight off, pull the On/Off Switch back.

5. A 12VDC device that draws less than 10 Amps can be plugged into the 12V

Inlet/Outlet (8) and powered by this unit’s battery. This will only work while the

ON/OFF switch is in its OFF position. Never try to power a device that uses

more than 10 Amps.

SKU 93255 For technical questions, please call 1-800-444-3353. Page 6

Maintenance

1. Store in a clean and dry location.

2. Charge the Battery after each use, and every three months if not used.

3. If the 12 VDC cord does not function, the fuse may be blown. Unscrew the

metal nut at one end of the cord and remove the old fuse. If the wire inside is

broken, replace with another F10A250V (Fast-acting, 10 Amp, 250 Volt) fuse

of the same type.

Battery Replacement

1. Remove the screws at the top back of the spotlight and open the Hatch (26).

2. Carefully pull out the existing Battery and pull off the wire terminals.

3. Replace the Battery with a new one of the same type (See page 2).

4. Push the red wire connector onto the positive (+) Battery terminal and the

black wire connector onto the negative (–) Battery terminal. Be sure that the

wires are connected properly. Otherwise, the Spotlight will be damaged.

5. Place Battery back into the battery compartment. Close the Back Cover, and

install and tighten screws.

6. Charge the new Battery as described on page 4.

Bulb Replacement

Note: Make sure all parts are cool to the touch before

replacing the bulb.

1. Pull the Lens Ring Cover (1) off and set it aside.

Un-thread the Lens Holding Ring (2), being careful

not to allow the Lens (3) to fall out.

2. Be careful - the edges of the Lens may be sharp!

Remove Lens and

gently

set it aside, it is fragile.

3. Remove the Refractor (4) and detach the three

wires leading to the Bulb (5).

4. Squeeze the ends of the Bulb Retaining Spring

(6) together, and hold them - see A, right.

5. Swing the Bulb Retaining Spring (6) up and remove

it - see B, right.

6. Turn the Bulb (5) slightly counterclockwise and

slide it out - see C, right.

7. Using a clean rag, cloth or gloved hand, install a

proper replacement Bulb without touching the bulb

portion. If the bulb is touched, it must be cleaned with rubbing alcohol and

allowed to dry before being installed. (Bulb replacement continued on next page.)

SKU 93255 For technical questions, please call 1-800-444-3353. Page 7

traPnoitpircseDtraPnoitpircseD

1revoCgniRsneL02geLdnatSraeRtfeL

2gniRgnidloHsneL12egniHdnatSraeR

3sneL22raBdnatSraeR

rewoL

4rotcarfeR32raBdnatSraeRreppU

5),09/001V214H(bluB42geLdnatSraeRthgiR

6gnirpSgniniateRbluB52yrettaBV21,hA7

7gn

isuoHtfeL62hctaHyrettaB

8teltuO/telnIV2172revoChctaHyrettaB

9revoCgnisuoHtfeL82gnisuoHthgiR

01revoCtroPgnigrahC92re

voCyrettaB

11revoCteltuO/telnIV2103revoCgnisuoHthgiR

21eldnaHtfeL13eldnaHthgiR

31raBdnatStnorFreppU23redilS

41raBdn

atStnorFrewoL33hctiwS

51revoCegniHdnatStnorF43nottuBsutatSyrettaB

61geLdnatStnorFtfeL53draoBtiucriC

71egniHdnatSt

norF63retpadAgulPraC

81geLdnatStnorFthgiR73retpadAgnigrahCCD/CA

91revoCegniHdnatSraeR

Parts List

NOTE: Some parts are listed and shown for illustration purposes only

and are not available individually as replacement parts.

8. Reassembly is the reverse of the

earlier steps. When reattaching the

wires, be certain that the wires are

reattached in the order shown to the

right.

SKU 93255 For technical questions, please call 1-800-444-3353. Page 8

Assembly Diagram

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS

MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR

MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR

SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED

TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR

DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD

BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER.THE

BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER

INSTALLATION OF REPLACEMENT PARTS THERETO.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chicago Electric Scheinwerfer Handbücher

Chicago Electric

Chicago Electric 3358 Kurzanleitung

Chicago Electric

Chicago Electric 94987 Kurzanleitung

Chicago Electric

Chicago Electric 03358 Bedienungsanleitung

Chicago Electric

Chicago Electric 93366 Kurzanleitung

Chicago Electric

Chicago Electric CHICAGO ELECTRIC 95799 Stücklistenhandbuch

Chicago Electric

Chicago Electric 65350 Bedienungsanleitung

Chicago Electric

Chicago Electric 8825 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Bedienungsanleitung

LIVARNO home

LIVARNO home 375304 2101 Originalbetriebsanleitung

Cameo

Cameo CLQS40WW Bedienungsanleitung

Leviton

Leviton Ellipsoid 5/50 Bedienungsanleitung

Monacor

Monacor img Stage Line PARL-56PDX/CR Bedienungsanleitung

Vector

Vector SL3AKV Bedienungsanleitung

Quantum

Quantum Q262 Betriebshandbuch

Philips

Philips Vari-lite VL3015LT Bedienungsanleitung

EUROSPOT

EUROSPOT C51 Bedienungsanleitung

DTS

DTS MINI BRICK ARC Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Handbuch

ACME

ACME LED-MS350B Bedienungsanleitung

EuroLite

EuroLite Akku flat light 1 Bedienungsanleitung

Commercial Electric

Commercial Electric SPTM-1401 Bedienungsanleitung

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Bedienungsanleitung

Teknik

Teknik FLEXI Bedienungsanleitung

Craftsman

Craftsman CMXLSB10 Bedienungsanleitung

EuroLite

EuroLite LED SLS-144 UV Floor Spot Bedienungsanleitung