Chicago Pneumatic Quiet CP7830Q Bedienungsanleitung

Operator’s Manual

CP7830Q & CP7830HQ

3/8” & 1/2” Ratchet Wrench

To reduce risk of injury, everyone using, installing, repairing,

maintaining, changing accessories on, or working near this tool

must read and understand these instructions before performing

any such task.

WARNING

CP7830Q & CP7830HQ

3/8” & 1/2” Ratchet Wrench

INSTRUCTION MANUAL

Machine Type:

This product is designed for installing and removing threaded

fasteners in wood, metal and plastic. No other use permitted.

For professional use only.

Air Supply Requirements

1. Supply tool with 90 psig (6.2 bar) of clean, dry air. Higher

pressure drastically reduces tool life.

2. Connect tool to air line using pipe, hose and tting sizes

shown in the diagram below.

Lubrication

1. Use an air line lubricator with SAE #10 oil, adjusted to

two (2) drops per minute. If an air line lubricator cannot be

used, add air motor oil to the inlet once a day.

2. Monthly, lubricate the drive bushing and ratchet yoke with

a good grade bearing grease. Periodically, depending

upon use, the ratchet head assembly should be removed,

cleaned and re-greased.

Reducing sound level by rotation of exhaust

deector

The tool is packaged with the exhaust air slots aligned with

the trigger and square drive. Rotating the exhaust deector

will further reduce noise levels, with the lowest noise levels

at approximately 180° from the as-shipped position.

Maintenance

1. Tool should be oiled on a daily basis for best performance.

Every 3 to 6 months the tool’s head should be greased

using approved CP Gear Grease. If the tool loses

performance over time, tool should be sent to a CP

Certied Service Center to be checked and repaired as

needed.

2. High wear parts are underlined in the parts list.

3. To keep downtime to a minimum, the following service kits

are recommended:

Tune-Up Kit: see part list 8940169404

1/2" (12mm)

3/8" (10mm)

3/8" (10mm)

3/8" (10mm)

CA048361 (1/2")

CA048362 (1/2")

CA048360 (1/2")

3/8" (10mm)

3/8" (10mm)

130

90

0

Learn more about air tools and compressors on our website.

Andere Handbücher für Quiet CP7830Q

3

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere Chicago Pneumatic Elektrowerkzeuge Handbücher

Chicago Pneumatic

Chicago Pneumatic CP 1210 Wartungs- und Serviceanleitung

Chicago Pneumatic

Chicago Pneumatic CP5000 Series Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic Erickson CP3109-19 Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP835 Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic B15B Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP8848-2 Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP826 Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic RX 2 Wartungs- und Serviceanleitung

Chicago Pneumatic

Chicago Pneumatic CP826 Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic MS 690 Wartungs- und Serviceanleitung

Chicago Pneumatic

Chicago Pneumatic CP8849 Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP 2190 Wartungs- und Serviceanleitung

Chicago Pneumatic

Chicago Pneumatic Chicago Pneumatic CP8745 Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic Quiet CP7830Q Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP7600 C Series Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP7829 Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP835B Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP871C Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP8738 Series Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic MS 695 Wartungs- und Serviceanleitung

Chicago Pneumatic

Chicago Pneumatic CP 1210 Wartungs- und Serviceanleitung

Chicago Pneumatic

Chicago Pneumatic CP749 Series Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic CP7600xB Series Bedienungsanleitung

Chicago Pneumatic

Chicago Pneumatic RediPower RP9426 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch