Chili ChiliPad Bedienungsanleitung
ChiliPadTM Instruction Manual
IMPORTANT—INSTRUCTIONS
DO NOT DESTROY
2
ChiliPadTM technology transforms your sleep experience
ChiliPadTM is dedicated to high-technology sleep engineering. Pursuing the perfect sleep, Chili-
PadTM allows users to control their sleep environment. Use our product for a better night’s
sleep. ChiliPadTM allows you to personalize your temperature so that you and your partner
can sleep at the temperature best for you.
We invite you to find your own… “degrees of comfort”!
Note:
Please read instructions carefully and thoroughly before use.
3
Table Of Contents
A. Introduction 4
B. Before You Use 5
C. Parts
List of Parts 6
Using the Control Unit 6
Using the Remote 7
D. Set Up
Connecting the Tubing 8
Conneting the Power 8
Filling the Control Unit with Water 9
Turning the Control Unit on and off 9-10
Adjusting the Temperature 10
Setting the Sleep Timer Function 11
E. Main Technical Parameters 12
F. Troubleshooting 13
G. Maintenance 14
4
So Hot—It’s Cool!
Your best night’s sleep is a few degrees away. If you have not yet achieved your perfect
night’s sleep or if you do not get enough of it, the ChiliPadTM is a solution. This is the only
cooling and heating temperature control system for your bed.
Wireless Control
Temperature range 68°F to 118° F , sleep timer option also available.
Easy to Wash
200 thread count mattress cover separates from pad so that it can be washed when needed.
Warning: Do not wash the pad. The pad maybe lightly cleaned by hand.
A: Introduction
5
1. Keep the control unit away from drafty areas that may become damp or wet such as an
open window. The control unit should be placed on a dry, ventilated and firm floor, free
of surrounding fabric. Spacing of 1 foot should be left on all sides.
2. Never turn on the power before a good connection is made between the unit and the bed
pad to prevent loss of heat-conducting liquid inside the unit.
3. The control unit has not been filled with water before factory delivery; make sure to fill as
needed. If by mistake, substantial liquid is lost, please fill with water. [The fill hole is on the
right side of the unit.]
4. Avoid kinking the hose between the control unit and the bed pad.
5. Be careful with sharp objects on the bed pad as to not puncture the coils in the bed pad.
6. Children should be under adult supervision when using the ChiliPadTM.
7. The ChiliPadTM is to be used on alternating–current supply circuit of the proper voltage.
8. Turn off or unplug when not in use.
9. Excessive heating may result from folding bedding, other than a mattress, when in actual
use.
10. If improper operation of this bedding is observed, discontinue its use immediately and con-
sult the manufacturer or the dealer regarding its repair.
11. Wrapping of a cord around the controller may damage the cord. Loop loosely when
storing.
B: Before You Use
6
NOTE: Single Zone ChiliPadTM will come with 1 remote and 1 control
unit
[a] [b]
[c] [d] [e]
Using the Control Unit
Dual Zone Bed 2 Remotes 2 Control Units
C: Parts
7
Using the Remote
ATemperatureincreasebutton.Maximumsetting118°F
BON/OFFbutton
CDisplay
DTemperaturedecreasebutton;minimumsettingis68°F
EEnterbutton
FSleepTimerbutton
The remote device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired opera-
tion.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
8
Place the ChiliPadTM on the bed
• The Pad should be placed under the sheets as if it was a regular mattress pad
Connecting the Tubing
• Connect tubing to the control unit as shown below
• Connect tubing from control unit to pad. (see diagram below)
Power Connection
• Insert the control unit’s power plug into the wall. The power indicator light will turn red
once plugged in.
• NOTE: This appliance has a polarized plug (one base is than the other). To reduce the
risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the
plug doe not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. DO NOT modify the plug in any way.
D: Set Up
9
Filling the Control Unit with Water
The ChiliPadTM does not come with water in it. You will need to fill before the first use.
The water reservoir is located in the top left corner of the control unit. Unscrew lid with
hand and add water until reservoir is full ( 3/4 cups). Turn control unit on, the water will
pump through the pad, continue to fill with water until full (2 cups). Screw lid on tight after
filling reservoir an resume with use.
Caution: Do not immerse control unit in water to fill.
Turning the Control Unit On
Press ON/OFF button on the control unit or remote, the control unit will “beep” at receiving
the signal, the pump and fan of the unit will start to run. The “cooling” or “warming” indicator
light will appear to indicate if the unit is cooling or warming.
When turned on the unit will always set itself to room temperature.
10
Turning Control Unit Off
Press ON/OFF button on the control unit or remote, the control unit will “beep” at receiving
the signal and the pump and fan will stop running.
If the unit will not be used for a long period of time, unplug from the wall.
Adjusting the Temperature
The control unit must be turned on to adjust temperature. Temperature can be adjusted be-
tween 65 and 105 F and is controlled in 1 degree increments.
To Cool:
• Press COOLER button to set to your desired temperature
• Press ENTER to signal the control unit to change to desired temperature. The control
unit will beep to confirm the setting was accepted.
To Warm:
• press WARMER button to set to your desired temperature
• Press ENTER to signal the control unit to change to desired temperature. The control
unit will beep to confirm the setting was accepted.
Andere Handbücher für ChiliPad
1
Inhaltsverzeichnis
