Chiron Technology IRIS 8xx Series Bedienungsanleitung

Chiron Technology

IRIS 8xx Series Alarm over IP Dialler

Installation and User Guide

Chiron Technology

Wyvols Court

Swallowfield

Reading

Tel: +44 (0)118 988 0228

E-mail: [email protected]

[email protected]

Chiron Technology Ltd 2006

Version 1.5 16/10/06

The information contained is supplied without liability for any errors or omissions. No part may be reproduced or used except as

authorised by contract or other written permission. The copyright and foregoing restriction on reproduction and use extend to all

media in which the information may be embedded.

Table of Contents

1OVERVIEW 7

2PRODUCT INVENTORY 8

3INTERFACES AND INDICATORS 9

3.1 IRIS 800 9

3.1.1 PCB Unit – Front Panel Indicators 9

3.1.2 PCB Unit – Rear Panel Connectors 9

3.1.3 Cased Unit – Front Panel Indicators 9

3.1.4 Cased Unit – Rear Panel Indicators 9

3.2 IRIS 820 10

3.2.1 PCB Unit – Front Panel Indicators 10

3.2.2 PCB Unit – Rear Panel Connectors 10

3.2.3 Cased Unit – Front Panel Indicators 10

3.2.4 Cased Unit – Rear Panel Connectors 10

3.3 IRIS 840 11

3.4 IRIS 850 12

3.4.1 PCB Unit – Front Panel Indicators and Connector 12

3.4.2 PCB Unit – Rear Panel Connectors 12

3.4.3 PCB Unit – Pin Inputs and Relay Outputs 12

4INSTALLATION – ALARM TRANSMISSION AND POLLING OVER IP 14

4.1 Preparation Prior to Installation 14

4.2 Physical Installation 14

4.3 Checking Network Connection 15

4.4 Polling Configuration 16

4.5 Alarm Transmission Configuration 17

5INSTALLATION – BACKUP TRANSMISSION OVER PSTN OR ISDN 18

5.1 Preparation Prior to Installation 18

5.2 Physical Installation 18

5.3 Checking Network Connection 18

5.4 Alarm Transmission Configuration 18

6INSTALLATION – BACKUP POLLING/TRANSMISSION OVER GPRS 20

Version 1.5 16/10/06 2

6.1 Preparation Prior to Installation 20

6.2 Physical Installation 20

6.3 Checking and Network Connection 20

6.4 Polling Configuration 21

6.5 Alarm Transmission 21

7INSTALLATION – BACKUP TRANSMISSION OVER GSM 22

7.1 Preparation Prior to Installation 22

7.2 Physical Installation and Checking Network Connection 22

7.3 Alarm Transmission 22

8ADVANCED INSTALLATION - DATA CALLS 23

8.1 Installation 23

8.2 Configuration 24

8.2.1 General 24

8.2.2 Calls over ISDN using V.120 Rate Adaption 24

8.2.3 Calls over Ethernet using TCP/IP 24

8.2.4 Calls over GPRS using TCP/IP 25

9ADVANCED INSTALLATION – PIN ALARMS 26

9.1 Installation 26

9.2 Default Alarm Messages 27

9.3 Configuration 27

10 ADVANCED INSTALLATION - SMS MESSAGING 29

10.1 Installation 29

10.2 Configuration 29

11 ALARM PANEL UPLOAD AND DOWNLOAD 31

12 LOCAL CONFIGURATION SOFTWARE 32

12.1 Installation of the Local Configuration Software 32

12.2 Connecting to the Dialler 32

Version 1.5 16/10/06 3

12.3 Running the Configuration Software 32

13 LOCAL CONFIGURATION WITH A TELEPHONE HANDSET 33

13.1 Dialler Default 33

13.2 IP Address 33

14 TROUBLESHOOTING 34

15 SPECIFICATION 35

15.1 Feature comparison 35

15.2 Polling over IP 36

15.3 Alarms over IP 36

15.4 Alarm and Polling Security 36

15.5 Alarm System Upload/Download 36

15.6 Alarm Interface 37

15.7 Ethernet Interface 37

15.8 ISDN Interface 37

15.9 PSTN Interface 37

15.10 GSM/GPRS Interface 38

15.11 SMS Messaging 38

15.12 Data Interface 38

15.13 Pin Inputs 38

15.14 Relay Outputs 38

15.15 LED Status Indicators 40

15.16 Power Supply 40

15.17 Weights 40

16 CONFORMANCE AND SAFETY 41

16.1 Conformance 41

16.2 Conformance to EN50131 and EN50136 41

Version 1.5 16/10/06 4

16.3 Safety 42

Version 1.5 16/10/06 5

Change History

Revision Date Changes

1.5 16/10/08 Added clarifications for EMC conformance

1.4 5/9/06 Added info on time for detection and reporting of alarms

and faults on alarm dialler and pin inputs.

Added details on serial interface data stop/parity/bits.

Changed analogue POTS voltage value to 40V peak.

Removed pin input sense resistors from inventory.

1.3 22/5/06 Requirement to install in suitable enclosure is now

mandatory rather than recommended.

1.2 25/1/06 Added IRIS 840.

1.1 29/12/05 Replace references to Velcro to self-adhesive feet.

Included sense resistors in inventory.

Change references to IRIS Configuration Console to IRIS

Configuration Software.

Added details for pin alarms.

Added product weights to spec section.

0.7 Original production version.

Version 1.5 16/10/06 6

1 Overview

The Chiron IRIS Alarm over IP Dialler range offers a unique way to connect any

standard alarm dialler over an IP network, with backup over traditional PSTN or

ISDN dial-up networks and/or GSM/GPRS wireless networks if required.

An integral polling mechanism is included in all products to provide constant

monitoring of the communications paths so that any problems are reported to the

ARC.

Advanced features such as data calls and SMS messaging are also offered.

The full set of features of each model in the range is included in the Specification

section at the end of this User Guide.

The Installation sections of this Use Guide sets out a straightforward set of

instructions for the installer from the most simple installation for alarm

transmission over an IP network, through installations with communications

backup routes, to more advanced installations which use data call and SMS

messaging features of the IRIS range.

Version 1.5 16/10/06 7

2 Product Inventory

The accessories included with each IRIS unit are as follows:

IRIS

800

(PCB)

IRIS

800

(Cased)

IRIS

820

(PCB)

IRIS

820

(Cased)

IRIS

840

(PCB)

IRIS

850

(PCB)

Main IRIS unit ••••••

Plug top mains power

supply

••

Power cable ••••

Ethernet cable (cream) ••••••

Dialler cable (grey) ••••••

ISDN cable (black) •••

PSTN cable (grey) •••

Installation guide ••••••

18K sense resistor ••••••

Antenna Optional Optional

When using the Local Configuration Software, a standard 9-way modem serial

cable is required for connection of the IRIS Dialler to a lap-top.

For the IRIS 840 and 850, the GSM SIM card can be obtained from the chosen

GSM network operator. Note that a SIM card offering both GSM and GPRS calls

is required to enable the full functionality.

Version 1.5 16/10/06 8

3 Interfaces and Indicators

The interface and indicators on each unit are shown below. Please see the

Installation sections for more details on how these are used.

3.1 IRIS 800

Note – for the IRIS 800 the PCB version is narrower than the cased version.

3.1.1 PCB Unit – Front Panel Indicators

DIAL

ETH

POLL

PWR ETH

3.1.2 PCB Unit – Rear Panel Connectors

DIAL V24

3.1.3 Cased Unit – Front Panel Indicators

Alarm Adapter

IRIS 800

DIAL SDETH POLL RD TR

3.1.4 Cased Unit – Rear Panel Indicators

ETHV24DIALPWR

Version 1.5 16/10/06 9

3.2 IRIS 820

3.2.1 PCB Unit – Front Panel Indicators

PSTN DIAL ETH POLL RD SD TR ISDN

3.2.2 PCB Unit – Rear Panel Connectors

PWR V24 ETH ISDN

PSTN DIAL

3.2.3 Cased Unit – Front Panel Indicators

Alarm Adapter

PSTN

IRIS 820

DIAL SDETH POLL RD TR ISDN

3.2.4 Cased Unit – Rear Panel Connectors

ISDNETHV24DIALPWR PSTN

Version 1.5 16/10/06 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chiron Technology Sicherheitssystem Handbücher

Chiron Technology

Chiron Technology IRIS Touch 200 Range Bedienungs- und Wartungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung