Christie LW555 Bedienungsanleitung
LW555 & LX505-605 Lamp-Filter Replacement Instruction Sheet 1 of 4
020-000239-03 Rev. 1 (07-2010)
LW555 & LX505-605
Lamp-Filter Replacement
Instruction Sheet
LAMP REPLACEMENT
When the projection lamp reaches its end of life, the Lamp
replacement icon appears on the screen and the LAMP REPLACE
indicator lights. Replace the lamp with a new one promptly. The
timing when the LAMP REPLACE indicator should light depends
on the lamp mode. Note: The Lamp replacement icon will not
appear when the Display indicator function is set to “Off”, or
during “Freeze”.
1. Turn off the projector and unplug the AC power cord and let the
projector cool for at least 45 minutes.
2. Loosen the screw and slide the lamp cover to open it.
3. Loosen 3 screws securing the lamp and pull out the lamp using
the built-in handle.
4. Replace the lamp with a new one. Make sure that the lamp is
properly and fully inserted and fasten 3 screws.
5. Close the lamp cover and secure the screw.
Allow a projector to cool for at least 45
minutes before you open the Lamp cover. The inside of
the projector can become very hot.
When replacing the lamp because it has
stopped illuminating, there is a possibility that the lamp
maybe broken. If replacing the lamp of a projector which
has been installed on the ceiling, you should always
assume that the lamp is broken, and you should stand to
the side of the lamp cover, not underneath it. Remove
the lamp cover gently. Small pieces of glass may fall out
when the lamp cover is opened. If pieces of glass get into
your eyes or mouth, seek medical attention immediately.
2 of 4 LW555 & LX505-605 Lamp-Filter Replacement Instruction Sheet
020-000239-03 Rev. 1 (07-2010)
For continued safety, replace with a lamp of the same type. Do not drop
the lamp or touch the glass bulb! The glass can shatter and may cause injury.
ORDER REPLACEMENT LAMP
HOW TO CHECK LAMP USED TIME
The LAMP REPLACE indicator will light yellow when the total lamp used time (Corresponding
value) reaches 3,000 hours. This is to indicate that lamp replacement is required.
The total lamp used time is calculated by using the following expression:
Total lamp used time (Corresponding value) = Teco + Tnormal x 1.5
where:
Teco : used time in the Eco1, Eco2 and Auto mode
Tnormal : used time in the Normal mode and Auto mode
To check the lamp used time:
1. Press and hold the ON STAND-BY button on the projector for more than 20 seconds.
2. The projector used time and lamp used time will be displayed on the screen briefly as follows.
WARNING MESSAGE ON THE NON-STANDARD LAMP USED
If a non-standard lamp is used, the warning and confirmation messages
will appear on the screen during each startup. Some of the functions are
limited when a non-standard lamp is used in spite of the warning.
MODEL LW555 LX505 LX605
TYPE NO. 003-120507-01 003-120531-01 003-120507-01
SERVICE PART NO. 6103469607 6103475158 6103469607
LW555 & LX505-605 Lamp-Filter Replacement Instruction Sheet 3 of 4
020-000239-03 Rev. 1 (07-2010)
REPLACING THE FILTER CARTRIDGE
The filter prevents dust from accumulating on the optical
elements inside the projector. Should the filter becomes clogged
with dust particles, it will reduce the cooling fans’ effectiveness
and may result in internal heat buildup and adversely affect the
life of the projector. This projector has an electrically operated
filter which helps you to replace the filter easily. The projector
monitors the condition of the filter at all times and automatically
scrolls to anew a filter when it detects clogging.
If the projector detects that the filter is clogged and no scroll is
left in the filter cartridge, a Filter cartridge replacement icon
appears on the screen and the WARNING FILTER indicator on
the top panel lights up. When you see this icon, replace the filter
cartridge and reset the Filter counter and the Scroll counter.
1. Turn off the projector, and unplug the AC power cord from
the AC outlet.
2. First, clean up the dust on the projector and around the air
vents.
3. Press downwards on the filter cover to release the latch
and open the filter cover.
4. Pull out the filter cartridge. When taking out the filter
cartridge, put your finger on the tab and then pull.
5. Insert new filter and close the filter cover. Make sure that the
filter cartridge is properly and fully inserted.
6. Connect the AC power cord to the projector and turn on the
projector.
7. Reset the filter counter and the scroll counter (see next page).
NOTICES! Make sure the filter cartridge is inserted in the
projector. If the filter cartridge is not inserted, the projector
cannot be turned on. Make sure the filter cover is closed when
using the projector. Do not put anything into the air vents. Doing
so may result in malfunction of the projector.
We recommend avoiding dusty/smoky environments when operating the projector. Usage in these
environments may cause poor image quality. When using the projector under these conditions, dust
may accumulate on a lens, liquid crystal panels, or optical elements inside the projector. When the
symptoms above are noticed, contact your authorized dealer or service station for proper cleaning.
ORDER REPLACEMENT FILTER
Type N o. Service Part No.
003-003084-01 6103469034
4 of 4 LW555 & LX505-605 Lamp-Filter Replacement Instruction Sheet
020-000239-03 Rev. 1 (07-2010)
RESETTING THE FILTER COUNTER
Be sure to reset the Filter counter after replacing
the filter cartridge.
1. Press the MENU button to display the On-
Screen Menu. Use the Point buttons to
select Setting and then press the Point or
the SELECT button.
2. Use the Point buttons to select Filter
counter and then press the SELECT button.
Use the Point buttons to select Filter
counter reset and press the SELECT button.
Filter counter reset? appears. Select [Yes] to
continue.
3. Another confirmation dialog box appears,
select [Yes]
RESETTING THE SCROLL COUNTER
Be sure to reset the Scroll counter after replacing
the filter cartridge.
1. Press the MENU button to display the On-
Screen Menu. Use the Point buttons to
select Setting and then press the Point or
the SELECT button.
2. Use the Point buttons to select Filter
counter and then press the SELECT button.
Use the Point buttons to select Scroll
counter reset and press the SELECT button.
Scroll counter reset? appears. Select [Yes] to
continue.
3. Another confirmation dialog box appears,
select [Yes] to reset the Scroll counter.
Andere Handbücher für LW555
2
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Christie Projektor Handbücher
Christie
Christie CP2230 Bedienungsanleitung
Christie
Christie HD2Kc Bedienungsanleitung
Christie
Christie CineLife+ RGB PLF Montageanleitung
Christie
Christie CP2420-Xe Bedienungsanleitung
Christie
Christie CP2306-RGBe Bedienungsanleitung
Christie
Christie CP2000-XB Bedienungsanleitung
Christie
Christie DS+26 Bedienungsanleitung
Christie
Christie M RGB Series Montageanleitung
Christie
Christie 1000W J Series Bedienungsanleitung
Christie
Christie LX400 Bedienungsanleitung
Christie
Christie Mirage HD25 Bedienungsanleitung
Christie
Christie CP4230 Bedienungsanleitung
Christie
Christie GS 2K Series Bedienungsanleitung
Christie
Christie D4K35 Bedienungsanleitung
Christie
Christie 38-VIV303-01 Bedienungsanleitung
Christie
Christie DWU951 Bedienungsanleitung
Christie
Christie Roadster X4 Bedienungsanleitung
Christie
Christie Matrix StIM-WQ Bedienungsanleitung
Christie
Christie Roadster S9 Bedienungsanleitung
Christie
Christie LX501 Betriebsanleitung
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
