Christie LW751i Bedienungsanleitung
1
LWU701i/LW751i/LX801i/LWU601i/LW651i
Setup Guide 020-000792-02
LIT GUID SET D2
ENGLISH
Projector
LWU701i/LW751i/LX801i
LWU601i/LW651i
Setup Guide (User's Manual (concise))
Thank you for purchasing this projector.
Read through this manual before using this projector, safely use this projector.
WARNING ►Before using this projector, be sure to read all manuals for this
projector.After reading them, store them in a safe place for future reference.
►Heed all the warnings and cautions in the manuals or on the projector.
►Follow all the instructions in the manuals or on the projector.
First of all............................................2
Entries and graphical symbols explanation......2
Important safety instruction ..............................2
Regulatory notices..............................3
About Electro-Magnetic Interference................3
About Waste Electrical and Electronic Equipment
...4
Contents of package...........................4
Preparing for the remote control.........5
Arrangement.......................................6
Connecting with your devices.............9
Fastening the adapter cover.............10
Attaching the terminal cover............. 11
Connecting power supply .................12
Turning on the power........................13
Adjusting the projector's elevator .....14
Adjusting the lens position................14
Displaying the picture.......................15
Turning off the power........................16
Replacing the lamp...........................17
Cleaning and replacing the air lter
..19
Replacing the internal clock battery...21
Using the CD manual .......................22
Specications ...................................23
Troubleshooting
- Warranty and after-service ...........25
Contents
NOTE •
In this manual, unless any comments are accompanied, “the manuals”
means all the documents provided with this projector, and “the product” means this
projector and all the accessories came with the projector.
http://www.pureglare.com.au
2020-000792-02
LIT GUID SET D2
LWU701i/LW751i/LX801i/LWU601i/LW651i
Setup Guide
First of all
Entries and graphical symbols explanation
The following entries and graphical symbols are used for the manuals and the projector
as follows, for safety purpose. Know their meanings beforehand and heed them.
Important safety instruction
The followings are important instructions for safely using the projector. Be sure to
follow them when handling the projector. The manufacturer assumes no responsi-
bility for any damage caused by mishandling that is beyond normal usage dened
in these manuals of this projector.
WARNING
This entry warns of a risk of serious personal injury or even death.
CAUTION This entry warns of a risk of personal injury or physical damage.
NOTICE This entry notices of fear of causing trouble.
WARNING ►
Never use the projector in or after an abnormality (for example,
giving off smoke, smelling strange, nding a foreign object inside, and so on.)
If an abnormality should occur, unplug the projector urgently.
►Situate the projector away from children and pets.
►Keep small parts away from children and pets. If swallowed, consult a
physician immediately for emergency treatment.
►Do not use the projector during electrical storms.
►Unplug the projector from the power outlet if the projector is not being used.
►
Do not connect the projector to a power supply while no lens unit is attached to it.
►Do not open or remove any portion of the projector, unless the manuals direct
it. For internal maintenance, leave it to your dealer or their service personnel.
►Use only the accessories specied or recommended by the manufacturer.
►Do not modify the projector or accessories.
►Do not let any things or any liquids enter to the inside of the projector.
►Do not get the projector wet.
►
Do not place the projector where any oils, such as cooking or machine oil, are used.
Oil may harm the projector, resulting in malfunction, or falling from the mounted position.
►Do not apply a shock or pressure to this projector.
- Do not place the projector on an unstable place such as the uneven surface
or the leaned table.
- Ensure the projector is stable. Place the projector so that it does not protrude
from the surface where the projector is placed on.
- Place your hands on the grip on the bottom of the projector when carrying the
projector.
- Remove all the attachments including the power cord and cables, from the
projector when carrying the projector.
►
Do not look into the lens and the openings on the projector, while the lamp is on,
since the projection ray may cause a trouble on your eyes.
►
Do not approach the lamp cover and the exhaust vents, while the projection lamp
is on. Allow the lamps to cool before touching them.
http://www.pureglare.com.au
3
LWU701i/LW751i/LX801i/LWU601i/LW651i
Setup Guide 020-000792-02
LIT GUID SET D2
ENGLISH
Regulatory notices
About Electro-Magnetic Interference
This is a Class A product. In a domestic environment this projector may cause
radio interference in which case the user may be required to take adequate
measures.
This projector may cause interference if used in residential areas. Such
use must be avoided unless the user takes special measures to reduce
electromagnetic emissions to prevent interference to the reception of radio and
television broadcasts.
In Canada
CAN ICES-3(A) / NMB-3(A).
In the US and places where the FCC regulations are applicable
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user is required to
correct the interference at his own expense.
INSTRUCTIONS TO USERS: Some cables have to be used with the core set.
Use the accessory cable or a designated type cable for the connection. For cables
that have a core only at one end, connect the core to the projector.
CAUTION: Changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
http://www.pureglare.com.au
4020-000792-02
LIT GUID SET D2
LWU701i/LW751i/LX801i/LWU601i/LW651i
Setup Guide
Contents of package
Your projector should come with the items
shown below. Check that all the items are
included. Contact your dealer immediately
if any items are missing.
(1) Remote control (Batteries not included)
(2) Power cord
(3) Computer cable
(4) Lens hole cover
(5) User’s manuals (Book x1, CD x1)
(6) Security label
(7) Application CD
(8) Adapter cover
(9) Terminal cover
(10) HDMI cable holder (x2)
(11) Cable tie (x2)
(12) HDMITM-DVI cable
NOTE • Keep the original packing materials for future reshipment. Be sure to
use the original packing materials when moving the projector. Remove the lens
unit and attach the lens hole cover when moving the projector.
About Waste Electrical and Electronic Equipment
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries or accumulators included with this equipment, display
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a
heavy metal content of more than 0.0005% Mercury or more than, 0.002%
Cadmium, or more than 0.004% Lead.
Regulatory notices (continued)
(5)
(6)
(2)
(3)
(4)
(1)
(7)
(8)
(9)
(10)
(11)
WARNING ►Keep small parts away from children and pets. Take care
not to put in the mouth. If swallowed, consult a physician immediately for
emergency treatment.
(12)
http://www.pureglare.com.au
5
LWU701i/LW751i/LX801i/LWU601i/LW651i
Setup Guide 020-000792-02
LIT GUID SET D2
ENGLISH
Preparing for the remote control
Insert the batteries into the remote control before using it. If the remote control
starts to malfunction, try to replace the batteries. If you do not plan to use the
remote control for long period, remove the batteries from the remote control and
store them in a safe place.
1. Holding the hook part of the battery
cover, remove it.
2. Align and insert the two AA batteries
according to their plus and minus
terminals as indicated in the remote
control. (Use the appropriate AA
carbon-zinc or alkaline batteries (non-
rechargeable) in accordance with laws
and regulations. Batteries are not
included.)
3. Replace the battery cover in the direction of the arrow
and snap it back into place.
WARNING ►Always handle the batteries with care and use them only as
directed. Improper use may result in battery explosion, cracking or leakage,
which could result in re, injury and/or pollution of the surrounding environment.
• When replacing the batteries, replace both of the batteries with new batteries
of the same type. Do not use a new battery with a used battery.
• Be sure to use only the batteries specied. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.
•
Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
•
Do not place a battery in re or water. Keep batteries in a dark, cool and dry place.
•
If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing the battery.
2
1 3
Installing the lens unit
See the manual of the optional lens.
http://www.pureglare.com.au
6020-000792-02
LIT GUID SET D2
LWU701i/LW751i/LX801i/LWU601i/LW651i
Setup Guide
Arrangement
Refer to tables T-1 to T-3 at the back of this manual as well as the following to
determine the screen size and projection distance. The values shown in the table
are calculated for a full size screen.
9.5
Projector top
Projector bottom
Ⓗ × Ⓥ : Screen size
ⓐ:
Projection distance
Secure a clearance of 50cm or greater between the exhaust vents and walls, and
a clearance of 30cm or greater between the intake vents and walls. Assume that
there is enough clearance in the front, back, and top of the projector in the gure
below.
Secure a clearance of 50cm or greater between the exhaust vents and walls.
Assume that there is enough clearance in the front, sides, and top of the pro-
jector in the gure below.
(continued on next page)
Elevator feet
50cm or greater
Intake
vents
Exhaust
vents
30cm or greater
50cm or greater
Exhaust
vents
http://www.pureglare.com.au
7
LWU701i/LW751i/LX801i/LWU601i/LW651i
Setup Guide 020-000792-02
LIT GUID SET D2
ENGLISH
Secure a clearance of 50cm or greater when installing the projectors side by
side. As for the required clearance not shown in the gure below, follow the
installation mentioned above.
Secure a clearance of 30cm or greater between the intake vents and walls
when installing the projector in portrait mode. As for the required clearance not
shown in the gure below, follow the installation mentioned above.
(continued on next page)
Arrangement (continued)
50cm or greater
30cm or greater
Intake
vents
http://www.pureglare.com.au
8020-000792-02
LIT GUID SET D2
LWU701i/LW751i/LX801i/LWU601i/LW651i
Setup Guide
WARNING ►Install the projector where you can access the power outlet
easily.
►Install the projector in a stable horizontal position.
• Do not use any mounting accessories except the accessories specied by the
manufacturer. Read and keep the manuals of the accessories used.
• For special installation such as ceiling mounting, be sure to consult your
dealer beforehand. Specic mounting accessories and services may be
required.
• Do not put the projector on its side, front or rear position.
• Do not attach nor place anything on the projector unless otherwise specied
in the manual.
►Do not install the projector near thermally conductive or ammable things.
►Do not place the projector where any oils, such as cooking or machine oil, are
used.
►Do not place the projector in a place where it may get wet.
►Do not block the intake vents and exhaust vents of the projector. If the intake
vents and exhaust vents of the projector are blocked, the accumulated inside
heat may cause re.
CAUTION ►Place the projector in a cool place with sufcient ventilation.
• Do not stop up, block nor cover the projector's vent holes.
• Do not place the projector at places that are exposed to magnetic elds, doing
so can cause the cooling fans inside the projector to malfunction.
►Avoid placing the projector in smoky, humid or dusty place.
• Do not place the projector near humidiers.
NOTICE ►Position the projector to prevent light from directly hitting the
projector’s remote sensor.
►
Do not place the projector in a place where radio interference may be caused.
►Set the ALTITUDE of the SERVICE item in the OPTION menu
correctly. It is recommended to leave it at AUTO usually. If the projector is used
with a wrong setting, it may cause damage to the projector itself or the parts
inside. For details, see User’s Manual - Operating Guide.
• When the temperature inside the projector rises high, it may cause the
high rotation of the fan for cooling temporarily.
NOTE
Arrangement (continued)
http://www.pureglare.com.au
9
LWU701i/LW751i/LX801i/LWU601i/LW651i
Setup Guide 020-000792-02
LIT GUID SET D2
ENGLISH
Connecting with your devices
Before connecting the projector to a device, consult the manual of the device to
conrm that the device is suitable for connecting with this projector and prepare
the required accessories, such as a cable in accord with the signal of the device.
Consult your dealer when the required accessory did not come with the projector or
the accessory is damaged.
After making sure that the projector and the devices are turned off, perform the
connection, according to the following instructions. Refer to gures F-1 to F-9 at the
back of this manual.
For details, see User’s Manual - Operating Guide. Before connecting the projector
to a network system, be sure to read User’s Manual - Network Guide too.
WARNING ►Use only the appropriate accessories. Otherwise it could
cause a re or damage the projector and devices.
• Use only the accessories specied or recommended by the projector’s
manufacturer. It may be regulated under some standards.
• Neither disassemble nor modify the projector and the accessories.
• Do not use the damaged accessory. Be careful not to damage the accesso-
ries. Route a cable so that it is neither stepped on nor pinched.
►
Heat may build up in the USB wireless adapter, to avoid possible burns dis-
connect the projector power cord for 10 minutes before touching the adapter.
• When using the USB wireless adapter, use the supplied adapter cover or
terminal cover (10, 11).
CAUTION ►For a cable with a core at only one end, connect the end with
the core to the projector. That may be required by EMI regulations.
►Before connecting the projector to a network system, be sure to obtain the
consent of the administrator of the network.
►
Do not connect the LAN port to any network that might have the excessive
voltage.
►
The designated USB wireless adapter that is sold as an option is required to use
the wireless network function of this projector. Before connecting the USB wireless
adapter, turn off the power of the projector and disconnect the power cord.
NOTE • Do not turn on or off the projector while connected to a device in
operation, unless that is directed in the manual of the device.
• Some input ports are selectable in the use. For details, see User's Manual -
Operating Guide.
• Be careful not to mistakenly connect a connector to a wrong port.
http://www.pureglare.com.au
10 020-000792-02
LIT GUID SET D2
LWU701i/LW751i/LX801i/LWU601i/LW651i
Setup Guide
When using the USB wireless adapter, use the supplied adapter cover for theft
prevention.
USB wireless adapter:
USB-WL-11N-NS
Temperature range: 0 ~ 45°C(operating)
1. Loosen the screw on the bottom left of the WIRELESS port.
2. Insert the tab of the cover into the hole at the upper right of the WIRELESS
port in the direction of the arrow.
3. Align the screw holes on the projector and the cover. Then insert the screw
removed from the projector into the hole and tighten the screw.
Fastening the adapter cover
WIRELESS DC5V 0.5A
LAN
Tab
WIRELESS DC5V 0.5A
WIRELESS DC5V 0.5A
LAN
WARNING ►Keep small parts away from children and pets. Take care not
to put in the mouth.
►Heat may build up in the USB wireless adapter, to avoid possible burns
disconnect the projector power cord for 10 minutes before touching the adapter.
http://www.pureglare.com.au
Andere Handbücher für LW751i
1
Dieses Handbuch passt für folgende Modelle
4
Inhaltsverzeichnis
Andere Christie Projektor Handbücher
Christie
Christie CP2000-SB Bedienungsanleitung
Christie
Christie DHD800 Bedienungsanleitung
Christie
Christie DWU951 Bedienungsanleitung
Christie
Christie CP4220 Bedienungsanleitung
Christie
Christie Solaria One Bedienungsanleitung
Christie
Christie Mirage 2000 Bedienungsanleitung
Christie
Christie DHD675-E Bedienungsanleitung
Christie
Christie 1000W J Series Bedienungsanleitung
Christie
Christie HS Series Montageanleitung
Christie
Christie J Series 2.0 kW Bedienungsanleitung
Christie
Christie 103-002001 Bedienungsanleitung
Christie
Christie M Series Bedienungsanleitung
Christie
Christie Mirage 304K Montageanleitung
Christie
Christie CP2308-C Betriebsanleitung
Christie
Christie RoadRunner L8 Bedienungsanleitung
Christie
Christie Roadster S+12K Bedienungsanleitung
Christie
Christie Captiva Series Bedienungsanleitung
Christie
Christie Christie DS+300 Bedienungsanleitung
Christie
Christie HS Series Bedienungsanleitung
Christie
Christie Boxer 30 Gebrauchs- und Pflegehandbuch
Beliebte Projektor Handbücher anderer Marken
Panasonic
Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung
NEC
NEC NP600S EDU Bedienungsanleitung
BenQ
BenQ SH753P Bedienungsanleitung
Eiki
Eiki EK-623U series Bedienungsanleitung
Epson
Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung
Epson
Epson PowerLite Home Cinema 705HD Bedienungsanleitung
