Christie LX1000 Bedienungsanleitung

LX1000 Lamp/Filter Replacement Instruction Sheet 1 of 4

020-000168-01 Rev. 1 (02-2009)

LX1000 Lamp/Filter Replacement

Instruction Sheet

INTRODUCTION

These instructions outline the details for Lamp and Filter replacement in the LX1000 projector (Model

No. 103-021104-01). NOTICE: Use only a Christie approved Lamp and Filter Kit for your specific

projector model.

KITS REQUIRED

003-120479-01 (Replacement Lamp)

003-002003-01 (Replacement Air Filter)

INSTRUCTIONS

LAMP REPLACEMENT

When the projection lamp reaches its end of life, the Lamp

replacement icon appears on the screen and the LAMP 1/ REPLACE

or LAMP 2/REPLACE indicator is orange. Replace the lamp with a

new one promptly. The timing for illumination of the lamp

replacement indicator depends on the lamp mode.

Allow the projector to cool for at least 45

minutes before the lamp cover is opened. The inside of the

projector can become very hot and may cause injury.

NOTICES: 1) Switch the lamp OFF before opening the lamp cover. 2) For continued safety, replace

with a lamp assembly of the same type. 3) Do not drop the lamp assembly or touch a glass bulb! The

glass can shatter and may cause injury.

NOTE: The Lamp replacement icon will not appear when the Display function is set to “Off”, or

during “Freeze”.

2 of 4 LX1000 Lamp/Filter Replacement Instruction Sheet

020-000168-01 Rev. 1 (02-2009)

1. Use the Lamp Status Display to verify which lamp (1 or 2)

requires replacement.

2. Press the Side Control ON/STANDBY button twice to switch

the projector OFF. Let the projector cool for at least 45

minutes (READY indicator will be green).

3. Switch the Main ON/OFF Switch to OFF and unplug the AC

power cord from the AC outlet.

4. Loosen the lamp cover screw and slide the lamp cover away

from the projector. Then lift the cover until it locks into place

in the open position.

5. Loosen the 2 screws securing the lamp to be replaced and pull

the lamp up by grasping the handle.

6. Install the new lamp and make sure the lamp is properly

seated. Tighten the 2 screws.

7. Close the lamp cover and tighten the screw.

8. Connect the AC power cord to the projector and switch the Main ON/OFF Switch to ON.

9. Press the ON-STANDBY button to switch the projector ON.

10. Reset the Lamp Replacement Counter (see instructions below).

Do Not operate the projector while any of the lamps are removed. This may

result in malfunctions, fire hazard, or other possible accidents.

NOTE: To maintain picture quality (better balance of color and brightness on entire screen), we

recommend replacing both lamps at one time.

RESETTING THE LAMP COUNTER

Make sure the Lamp counter is reset after a lamp is replaced. When the Lamp counter is reset, the

LAMP 1/ REPLACE or LAMP 2/REPLACE indicator will switch off and the Lamp replacement icon

will disappear.

1. Press the MENU button on the side-control to display

the On-Screen Menu. Use the Point buttons to

move the red frame pointer to the Setting Menu icon.

2. Use the Point buttons to move the red frame pointer

to Lamp counter and then press the Select button. A

dialog box appears. Select a lamp to display “Lamp

replacement counter Reset?”. Select [Yes] to continue.

3. In the confirmation dialog box,select [Yes] to reset the

Lamp counter.

NOTE: Do not reset the Lamp counter without replacing a

lamp.

LX1000 Lamp/Filter Replacement Instruction Sheet 3 of 4

020-000168-01 Rev. 1 (02-2009)

REPLACING THE FILTER CARTRIDGE

1. Press the Side Control ON/STANDBY button twice to switch

the projector OFF. Let the projector cool for at least 45 min-

utes (READY indicator will be green).

2. Switch the Main ON/OFF Switch to OFF and unplug the AC

power cord from the AC outlet.

3. Clean the dust from the projector and around the air vents.

4. Slide the Filter cover to access the filter (see figure at right).

5. Hold the finger grip and pull to remove the filter cartridge.

6. Place a new filter into position. Make sure that the filter

cartridge is properly and fully inserted.

7. Close the filter cover.

8. Connect the AC power cord to the projector and switch the

Main ON/OFF Switch to ON.

9. Press the ON-STANDBY button to switch the projector ON.

10. Reset the Filter counter (see instructions below).

NOTICES: 1) Make sure the filter cartridge is correctly inserted

into the projector otherwise, the projector cannot be turned on.

Do not block the air vents. Doing so may result in malfunction of

the projector. 2) It is recommended that dusty/smoky environments

are avoided when operating the projector. Usage in these environments may cause poor image quality.

When using the projector under dusty or smoky conditions, dust may accumulate on a lens, liquid

crystal panels, or optical elements inside the projector. Such conditions may degrade the quality of the

projected image. When the symptoms above are noticed, contact your authorized dealer or service

station for proper cleaning.

4 of 4 LX1000 Lamp/Filter Replacement Instruction Sheet

020-000168-01 Rev. 1 (02-2009)

RESETTING THE FILTER COUNTER

Make sure the Filter counter is reset after the filter cartridge is replaced.

1. Press the MENU button to display the On-Screen Menu.

Use the Point buttons to move the red frame pointer to

the Setting Menu icon.

2. Use the Point buttons to move the red frame pointer to

Filter counter and then press the SELECT button. A dialog

box appears showing the Used time option and the Scrolls

remaining option. Use the Point buttons to select Used

time.

3. Used time shows the total accumulated time of the filter use,

a timer setting option, and the Reset option. Select Reset

and the “Filter counter Reset?” appears. Select [Yes] to

continue.

4. In the confirmation dialog box, select [Yes] to reset the

Filter counter.

RESETTING THE SCROLL COUNTER

Make sure the Scroll counter is reset after the filter cartridge is replaced.

1. Press the MENU button to display the On-Screen Menu.

Use the Point buttons to move the red frame pointer to

the Setting Menu icon.

2. Use the Point buttons to move the red frame pointer to

Filter counter and then press the SELECT button. A dialog

box appears showing the Used time option and the Scrolls

remaining option. Use the Point buttons to select

Scroll(s) remaining.

3. Scroll(s) remaining shows the number of the remaining

scrolls and the Reset option. Select Reset and the “Scroll

counter Reset?” appears. Select [Yes] to continue.

4. In the confirmation dialog box, select [Yes] to reset the

Scroll counter.

NOTE: While the scroll counter reset is in progress, a “Please

wait...” message appears on the screen, the cooling fans operate

and the filter cartridge is adjusted.

Andere Handbücher für LX1000

Inhaltsverzeichnis

Andere Christie Projektor Handbücher

Christie

Christie DS+ Series Bedienungsanleitung

Christie

Christie Mirage 4K40-RGB Bedienungsanleitung

Christie

Christie Mirage 4K35 Bedienungsanleitung

Christie

Christie Christie LX120 Bedienungsanleitung

Christie

Christie IMB-S2 Stücklistenhandbuch

Christie

Christie HS Series Betriebsanleitung

Christie

Christie J series 2.0kW Bedienungsanleitung

Christie

Christie HS Series Bedienungsanleitung

Christie

Christie I Series Bedienungsanleitung

Christie

Christie 38-VIV212-01 Bedienungsanleitung

Christie

Christie APS Series Bedienungsanleitung

Christie

Christie Mirage 4K25 Bedienungsanleitung

Christie

Christie DHD600-G Bedienungsanleitung

Christie

Christie LX605 Bedienungsanleitung

Christie

Christie Boxer 4K Gebrauchs- und Pflegehandbuch

Christie

Christie Solaria One Bedienungsanleitung

Christie

Christie HS 2K Series Bedienungsanleitung

Christie

Christie Matrix 1500 Bedienungsanleitung

Christie

Christie 38-VIV208-03 Bedienungsanleitung

Christie

Christie Q Series Bedienungsanleitung

Christie

Christie MIRAGE DS+8K-J Bedienungsanleitung

Christie

Christie GraphXMASTER DLV1400-DX Bedienungsanleitung

Christie

Christie D4K2560 Bedienungsanleitung

Christie

Christie 103-006101-01 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung