Christie Roadie HD+35K Bedienungsanleitung

Roadie HD+35K Portrait Upgrade Kit Instruction Sheet 1 of 4

020-100778-03 Rev. 1 (03-2012)

Roadie HD+35K Portrait Upgrade Kit

Instruction Sheet

SAFETY AND WARNING GUIDELINES

HIGH VOLTAGES MAY BE EXPOSED! Always power down and

disconnect power sources prior to servicing. Once the projector is

powered down, allow the cooling fans to automatically turn OFF before

disconnecting from AC and opening the projector.

QUALIFIED SERVICE TECHNICIANS REQUIRED! All module

replacement procedures must be performed by Christie accredited

service technicians.

NON-INSULATED DANGEROUS VOLTAGES MAY BE EXPOSED! Always

disconnect from AC prior to disassembly.

OBSERVE ALL ELECTROSTATIC PRECAUTIONS! Use a grounded wrist

strap when handling electronic assemblies.

Never operate the projector (or the fans) without all the covers installed.

Failure to operate the projector in the correct portrait mode orientation

can cause severe damage to the projector.

INTRODUCTION

The Roadie HD+35K projector must be installed in a Christie rigging

frame (P/N 38-814007-XX) and suspended as not to block

ventilation. The projector can be used in portrait mode after installing

the upgrade kit. The following instructions detail the steps required

to install the portrait upgrade kit.

2 of 4 Roadie HD+35K Portrait Upgrade Kit Instruction Sheet

020-100778-03 Rev. 1 (03-2012)

KITS REQUIRED

Kit Portrait Mode Roadie (P/N 000-102632-XX) includes:

• (1) Lamp Anode Stand Assembly (P/N 000-102637-XX)

• (3) Rubber Isolator (P/N 012-100753-XX)

• (3) 10-32 Screw (P/N 012-100425-XX)

• (3) Flat washers (P/N 012-100500-XX)

• (2) Wire rope lanyard 6-inch LG (P/N 012-100997-XX)

TOOLS REQUIRED

• #2 Phillips® screwdriver

• 3/8-inch wrench

• 3/16-inch Hex driver

INSTRUCTIONS

FRONT TOP COVER

Secure the front top cover to the projector to prevent it from falling off while using in portrait mode.

Cover Should be locked when projector is in use.

1. Unlock the lid.

2. Lift lid.

3. Loop cable through slot.

4. Feed terminal end through the loop.

5. Remove screw and install terminal.

6. Reinstall screw.

7. Repeat steps 2-5 for other side.

8. Close and lock lid.

Roadie HD+35K Portrait Upgrade Kit Instruction Sheet 3 of 4

020-100778-03 Rev. 1 (03-2012)

NEW LAMP ANODE STAND

Replace the existing lamp anode stand with the new one.

1. Open lamp door.

2. Remove existing lamp anode stand.

3. Install new lamp anode stand in the orientation shown.

NOTE: 1) The opening must be farthest away from the lamp door. 2) Torque screws to 35in-lbs

(4Nm).

4. Close lamp door.

4 of 4 Roadie HD+35K Portrait Upgrade Kit Instruction Sheet

020-100778-03 Rev. 1 (03-2012)

FAN VIBRATION ISOLATORS

Replace the existing gel isolators with rubber isolators.

1. Remove back top cover and exhaust lid assembly. See section 5.3.2 Back Top Cover/Exhaust Lid

Assembly of the service manual (P/N 020-100341-XX) for more details.

2. Remove (3) nuts securing the fan bracket to the vibration mounts.

3. Remove fan bracket assembly carefully.

4. Remove the existing (3) gel isolators.

5. Install (3) new black rubber isolators.

6. Reinstall the fan bracket assembly.

7. Secure the fan bracket assembly to the new rubber isolators with the (3) 10-32 screws and the (3)

flat washers provided.

8. Torque the (3) screws to 12in-lbs (1.36Nm).

9. Reinstall the back top cover and the exhaust lid assembly.

PROJECTOR ORIENTATION

For portrait mode, the projector MUST be oriented with lens closest to

the top side up. Failure to do so will cause damage to the projector. Max

tilt ±15 degrees.

Once oriented in portrait mode, lamp alignment must be performed for optimum brightness.

Andere Handbücher für Roadie HD+35K

Inhaltsverzeichnis

Andere Christie Projektor Handbücher

Christie

Christie HS Series Bedienungsanleitung

Christie

Christie 38-VIV210-01 Bedienungsanleitung

Christie

Christie LX37 Bedienungsanleitung

Christie

Christie LW400 Bedienungsanleitung

Christie

Christie LWU505 Bedienungsanleitung

Christie

Christie 4K40-RGB Series Bedienungsanleitung

Christie

Christie CineIPM-2K Bedienungsanleitung

Christie

Christie Solaria One Bedienungsanleitung

Christie

Christie 38-809050-01 Bedienungsanleitung

Christie

Christie D4K2560 Bedienungsanleitung

Christie

Christie DWU1052 Bedienungsanleitung

Christie

Christie Cinema 4K-RGB CP4325-RGB Bedienungsanleitung

Christie

Christie Q Series Installations- und Betriebsanleitung

Christie

Christie CP2309-RGB Bedienungsanleitung

Christie

Christie Vivid LX35 Bedienungsanleitung

Christie

Christie LX605 Bedienungsanleitung

Christie

Christie D Series Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Christie

Christie Roadie HD+35K Bedienungsanleitung

Christie

Christie CineX35 DATZ Bedienungsanleitung

Christie

Christie D4K Series Betriebsanleitung

Christie

Christie Vivid LX41 Bedienungsanleitung

Christie

Christie DS+750 Bedienungsanleitung

Christie

Christie LW502 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

Epson

Epson PowerLite 810p Bedienungsanleitung

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Bedienungsanleitung