Christie Roadster Bedienungsanleitung

Boresight Alignment Procedure Instruction Sheet 1 of 3

020-100116-01 Rev. 1 (11/07)

Boresight Alignment Procedure

Instruction Sheet

INTRODUCTION

The following instructions outline Boresight Adjustment on any Roadster, Mirage, Matrix, DLV,

Christie DS and Christie DW model projector.

Boresight alignment ensures the projection lens is precisely parallel with the exit-face of the prism and

that the correct distance exists between the exit face and the input of the projection lens. Typically, this

procedure is performed whenever a lens mount is replaced to ensure the displayed image has optimum

focus in all four corners and the center.

NOTICE: Projectors must be serviced in a clean environment to prevent dust particles from settling on

optical components.

TOOLS REQUIRED

Lens cap with pinhole in center (Recommended, but not necessary).

WARNINGS

Replacement must be performed by qualified Christie service personnel only.

Observe all electrostatic precautions.

2 of 3 Boresight Alignment Procedure Instruction Sheet

020-100116-01 Rev. 1 (11/07)

INSTRUCTIONS

NOTE: For DLV1400-DX and DLV1920-DX models, refer to Boresight Alignment for Fixed Lens

Mount Models, on page 3.

1. Set the spacing behind screws 1a, 2a, 3a and 4a

to 4mm. Refer to Figure 1.

2. Load the “GRID” internal test pattern (Figure

2).

3. Using the IR keypad, use to enable

the green only.

4. Focus the lens on the screen at the correct size

for the throw ratio of the lens (approximately

center of focus range). See Figure 2. For 0.73

lenses only, set the focus adjustment ring to

mid-range.

5. Ensure the projected image is perfectly square

on the wall with no visible horizontal or vertical

keystone. If vertical keystone is observed, adjust the projector’s feet until it is level and the image

appears rectangular.

6. Adjust the horizontal and vertical lens offsets

until the image is centered in the lens (Figure

3). NOTE: Use a lens cap with a pinhole in the

center or hold a sheet of paper in front of the

lens and then center the image.

Figure 1 Boresight Adjustment Screws

Func

Figure 2 Grid Test Pattern

Figure 3 Offset Adjustment

Boresight Alignment Procedure Instruction Sheet 3 of 3

020-100116-01 Rev. 1 (11/07)

You are now ready to perform a precision boresight alignment on the projector to achieve the best

possible uniform focus.

1. Back off each corner locking screw (1b, 2b, 3b, & 4b) - refer to Figure 1).

2. Observe which portion of the image is out of focus. For example if the top left corner of the image

is out of focus than you will need to adjust screw 3a until that point is correctly focused (see Grid

Test Patterrn at right).

3. Then, observe the bottom right corner of the image, which will now be out of focus. Adjust screw

1a to correctly focus that point. NOTES: 1) You will have to alternate adjustments to both screws

until both points come into focus (or fairly close to focus). 2) Observe the opposite corners while

performing these adjustments as those opposite corners may come into focus as you are adjusting

the first 2 corners.

4. Adjust screw 2a until the top right corner is in focus.

5. Adjust screw 4a until the bottom left corner is in focus.

All four corners plus the center should now be correctly focused. NOTE: If the alignment process

causes the image to shift side-to-side or up and down by more than a few inches, re-center the image

using the lens cap with pinhole. Adjust the horizontal and vertical offsets to bring the image back to

the center. The image may have to be checked and re-centered a few times throughout this procedure.

BORESIGHT ALIGNMENT FOR FIXED LENS MOUNT DLV1400-DX AND

DLV1920-DX MODELS

When aligning boresight on the DLV model prjector, ensure the points below are observed:

• Use a 1.2:1 fixed lens.

• Focus the image as outlined in the steps above.

Andere Handbücher für Roadster

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Christie Projektor Handbücher

Christie

Christie LX750 Bedienungsanleitung

Christie

Christie DCP Series Bedienungsanleitung

Christie

Christie Mirage S+2K Bedienungsanleitung

Christie

Christie DS+750 Bedienungsanleitung

Christie

Christie HAL Series Bedienungsanleitung

Christie

Christie RPMSP-D120U Montage- und Bedienungsanleitung

Christie

Christie LX400 Bedienungsanleitung

Christie

Christie Mirage WU-L Bedienungsanleitung

Christie

Christie LX400 Bedienungsanleitung

Christie

Christie DS+750 Bedienungsanleitung

Christie

Christie Griffyn 4K50-RGB Montageanleitung

Christie

Christie Boxer 4K Series Bedienungsanleitung

Christie

Christie Christie LU77 Bedienungsanleitung

Christie

Christie Boxer 30 Benutzerhandbuch

Christie

Christie 38-RS1001-02 Bedienungsanleitung

Christie

Christie D4K2560 Bedienungsanleitung

Christie

Christie 4K35-RGB Gebrauchs- und Pflegehandbuch

Christie

Christie M Series Bedienungsanleitung

Christie

Christie LX1750 Bedienungsanleitung

Christie

Christie CP2208-LP Bedienungsanleitung

Christie

Christie Vivid LX41 Bedienungsanleitung

Christie

Christie DS Series Bedienungsanleitung

Christie

Christie 35/70 Handbuch

Christie

Christie CineX35 DATZ Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Asus

Asus ZenBeam Latte Bedienungsanleitung

Epson

Epson PowerLite 810p Bedienungsanleitung

BOXLIGHT

BOXLIGHT CP-322i/CP-634i Bedienungsanleitung