Chromalox 8003 Bedienungsanleitung
8003
Issue Date
April 1994
❒USER’S MANUAL
0037-75212
1/8 DIN
Temperature Controller
8003 Cover 4/27/06, 2:26 PM1
Chromalox 8003 User's Manual i
Contents
Model Identification .................................................................................................................................... Page ii
Dimensions and Panel Cutout ............................................................................................................................1
Wiring ...........................................................................................................................................................................2
Hardware Setup .......................................................................................................................................................3
Configuration Mode ...............................................................................................................................................4
Operator Mode .........................................................................................................................................................9
Error Messages ..................................................................................................................................................... 12
Warranty and Return ........................................................................................................................................... 14
8003 TOC 4/27/06, 2:23 PM1
ii Chromalox 8003 User's Manual
Model Identification
Model
8003 1/8 DIN Temperature Controller
Code Output 1 - Heat or Cool
1 SPDT Relay, 3 Amps at 250 Vac (Resistive) or
SSR Drive, 14V @ 20mA, Jumper Selectable
Code Output 2 - Cool or Alarm
1 Relay, 2 Amps at 250 Vac (Resistive) or
SSR Drive, 14V @ 20mA, Jumper Selectable
Code Options
0 None
1 Alarm #2, 2 Amps at 250 Vac (Resistive load)
Code Power Supply
3 100/240 Vac
5 24 Vac/dc
Code
0 Add to complete model number
8003 - 11130Typical Model Number
8003 TOC 4/27/06, 2:23 PM2
Chromalox 8003 User's Manual 1
Dimensions in inches (mm in parenthesis)
Chromalox
SMRT
PV
MAIN AL1 AL2 SMRT
FUNC
COOL HB
SP
0.5
(12.8)
3.5
(89)
1.9
(48)
3.8
(96)
1.77
(45)
3.62
(92)
5.1
(125)
2.4
(60)
8003 Manual 4/27/06, 2:24 PM1
2Chromalox 8003 User's Manual
Warnings:
• When a relay output is used to drive an inductive
load, it is suggested that you connect an external
snubber network (RC) across the terminals in
accordance with the following table (or use
Chromalox snubber P/N 0149-01305):
• Do not run sensor input wires together with power
cables.
• For thermocouple (TC) wiring, use matching
thermocouple extension wire (i.e. for J T/C, use type
“J” thermocouple extension wire).
• When using shielded sensor cable, ground the shield
at one end only.
Wiring 12
13
14
15
16
17
18
19
20
21
22
PWR
Line
RTD
-
+
C
NC
-
+
1
TC
3
4
5
6
7
8
9
10
11
C
(mF)
0.047
0.1
0.33
R
(Ω)
100
22
47
P.
(W)
1/2
2
2
Operating
Voltage
260 Vac
260 Vac
260 Vac
Load
Current (mA)
<40 mA
<150 mA
<0.5 A
OUT2
SSR
AL1/COOL
OUT2
RELAY
AL1/COOL
OUT1
SSR
OUT1
RELAY
OUT3
AL2
RELAY
TC+
TC-
NO
NO
C
NO
C
8003 Manual 4/27/06, 2:24 PM2
Chromalox 8003 User's Manual 3
Hardware Setup
To select the output type(s) and the alarm contact settings:
1. Remove the instrument from its case.
2. Move the jumpers to the desired position as shown in
the diagram.
3. Set J304 and J305 as shown in the following figure.
PZ22
PZ21
PZ20
PZ19
PZ18
PZ17
PZ16
PZ15
PZ14
PZ13
PZ12
1
1
J305
(MAIN output)
1-2 = SSR
2-3 = Relay
J304
(AL1, Cool.)
1-2 = SSR
2-3 = Relay
3 2 1
3 2 1
J305
J304
8003 Manual 4/27/06, 2:24 PM3
4Chromalox 8003 User's Manual
General Operation
There are two setup modes for the 8003:
• Configuration Mode
• Operator Mode
In general, the Configuration Mode is the initial setup of
the controller when first installed. Input type and alarm
setup are examples of Configuration Mode settings. The
Operator Mode includes settings that might be adjusted
frequently with daily control operations such as setpoints
and PID parameters.
Notes for Configuration Mode:
FUNC = Stores the new value of a selected parameter
and increments to the next parameter.
SMRT = Scrolls parameters back (in reverse order)
without storing the new parameter value.
▲ = Increases the value of the selected parameter.
▼ = Decreases the value of the selected parameter.
Configuration Procedure
1. Remove the instrument from its case.
2. Set the internal switch V2 (see the following
figure) in open position.
3. Reinsert the instrument in its case.
4. Switch on the instrument. “CNF” should be displayed
in the upper display.
Note: If "CAL" indication is immediately displayed,
press the ▲pushbutton to return to the
configuration mode (CNF).
5. Push the FUNC pushbutton.
The lower display shows the parameter code while
the upper display shows the actual parameter value.
PZ1
PZ3
PZ4
PZ6
PZ7
PZ10
PZ11
V2
8003 Manual 4/27/06, 2:24 PM4
Chromalox 8003 User's Manual 5
P1 = Input Type and Standard Range
Range
0 = TC type L 0 / +800 °C
1 = TC type J 0 / +800 °C
2 = TC type K 0 / +999 °C
3 = TC type N 0 / +999 °C
4 = RTD type Pt 100 -199 / +500 °C
5 = RTD type Pt 100 -19.9 / +99.9 °C
8 = TC type L 0 / +999 °F
9 = TC type J 0 / +999 °F
10 = TC type K 0 / +999 °F
11 = TC type N 0 / +999 °F
12 = RTD type Pt 100 -199 / +999 °F
P2 = Initial Scale Value
Not present when P1 = 5
The initial and full scale values are used by the PID
algorithm to calculate the input span.
P3 = Full Scale Value
Not present when P1 = 5
The initial and full scale values are used by the PID
algorithm to calculate the input span.
Note: the minimum input span (P3 - P2) is 300°C or
600°F for TC input and 100°C or 200°F for RTD input.
P4 = Output Configuration
H = Heating HC = Heating / cooling
P5 = Heating Output Type
rEL = Relay
SSr = SSR
The output type selected here must match hardware
jumper setup (see page 2).
P6 = Cooling Element
Available only when P4 = HC
AIr = Air
OIL = Oil
H2O = Water
P7 = Alarm 1 Type
Available only when P4 = H
0 = None
1 = Process alarm (absolute)
2 = Band alarm (+ and - deviation)
3 = Deviation alarm
P8 = Alarm 1 Operation
Available only when P7 is different from 0
H = High Alarm L = Low Alarm
(outside if band alarm) (inside if band alarm)
8003 Manual 4/27/06, 2:24 PM5
6Chromalox 8003 User's Manual
P9 = Alarm 1 Inhibit
Available only when P7 is different from 0.
OFF = inhibit disabled
ON = inhibit enabled
Note: The Alarm Inhibit disables the alarm action after a
setpoint change. At startup, it automatically enables the
alarm when the process temperature reaches the present
condition.
P10 = Alarm 2 Type
0 = Not provided 2 = Band alarm
1= Process alarm 3 = Deviation alarm
P11 = Alarm 2 Operative Mode
Available only when P10 is different from 0.
H = High Alarm L = Low Alarm
P12 = Alarm 2 Inhibit
Available only when P10 is different from 0
OFF = Inhibit disabled
ON = Inhibit enabled
Note: The Alarm Inhibit disables the alarm action after a
setpoint change. At startup, it automatically enables the
alarm when the process temperature reaches the present
condition.
P13 = Type of OFFSET Applied to the Measured Value
P13 = 0 = constant OFFSET (P14) all over the range
P13 different from 0 = P13 shows the application point
of the offset value set by P14 parameter.
P14 = OFFSET Value
When P13 = 0, P14 is programmable, in engineering
units, from -20 % to +20 % of the input range.
When P13 is different from 0, P14 is programmable from
-20 % to + 20 % of P13 value.
P13 = 0
Real curve
Readout
Adjusted
curve
P13
Real curve
Adjusted curve
Readout
P14
Input
P14
Input
-20% to +20%
8003 Manual 4/27/06, 2:24 PM6
Chromalox 8003 User's Manual 7
P15 = Threshold of the “Soft Start” Function
Enter the threshold value, in °F or °C, for the automatic
start of the "Soft Start" function (output power limit).
The range of this setting is determined by the range of the
sensor selected in P1 (i.e., if type J T/C °F is selected in
P1, range is 0-999).
If the unit powers-up below the threshold value, the "Soft
Start" function is enabled and limits the power output to
"OLH" for "toL" minutes. “OLH” and “toL are setup in
the Operator Mode.
P16 = Not used
P17 = Not used
P18 = User Defined Security Code
0 = Security lock disabled (all Operator Mode parameters
may be adjusted)
1 = Security lock enabled (only setpoints may be adjusted)
From 2 to 499 = SP parameter may be modified and
other Operator Mode parameters may
be accessed.
From 500 to 999 = SP, A1 and A2 parameters may be
modified and other Operator Mode
parameters may be accessed.
• When configuration is completed, the instrument
shows " -.-.-. " on both displays.
End of Configuration
• Push the FUNC pushbutton. The instrument will
return to the beginning of the configuration procedure.
For Advanced Configuration
• Push the ▲or ▼pushbutton and set the “217” code on
the upper display.
• Push FUNC. The following advanced configuration
parameters, P19-P29 will be displayed.
P19 = Main Output Action
Available only when P4 = H
r = Reverse (heating)
d = Direct (cooling)
Note: when P4 = HC, this parameter is forced to "r"
P21 = Alarm 1 Relay Action
This parameter is available only if P7 is different from 0
and P4 = H.
r = Reverse (relay de-energized in alarm condition)
d = Direct (relay energized in alarm condition)
8003 Manual 4/27/06, 2:24 PM7
Inhaltsverzeichnis
Andere Chromalox Temperaturregler Handbücher
Chromalox
Chromalox LIMIT Bedienungsanleitung
Chromalox
Chromalox 1604 Bedienungsanleitung
Chromalox
Chromalox 1601 Bedienungsanleitung
Chromalox
Chromalox 1020 Bedienungsanleitung
Chromalox
Chromalox 2110 Bedienungsanleitung
Chromalox
Chromalox 6020 Gebrauchsanweisung
Chromalox
Chromalox TEMPERATURE CONTROLLER 1604-7 Bedienungsanleitung
Chromalox
Chromalox 2110 Bedienungsanleitung
Chromalox
Chromalox 2002 PLUS! Bedienungsanleitung
Chromalox
Chromalox 2104 Bedienungsanleitung
Beliebte Temperaturregler Handbücher anderer Marken
Swegon
Swegon LUNAd MB Bedienungsanleitung
Lucky Reptile
Lucky Reptile Thermo Control II Bedienungsanleitung
SENSORMETRIX
SENSORMETRIX Argon 100 Bedienungsanleitung
Fuji Electric
Fuji Electric PXE4 Bedienungsanleitung
Yuyao gongyi
Yuyao gongyi XMT-808 series Bedienungsanleitung
Selec
Selec TC544C Bedienungsanleitung
