Chrysler 300M 2002 Bedienungsanleitung

CHRYSLER/DODGE

SERVICE MANUAL

2002

300M, CONCORDE

AND INTREPID

NO PART OF THIS PUBLICATION MAY BE

REPRODUCED, STORED IN A RETRIEVAL

SYSTEM, OR TRANSMITTED, IN ANY FORM OR

BY ANY MEANS, ELECTRONIC, MECHANICAL,

PHOTOCOPYING, RECORDING, OR OTHERWISE,

WITHOUT THE PRIOR WRITTEN PERMISSION

OF DAIMLERCHRYSLER CORPORATION.

DaimlerChrysler Corporation reserves the right to make changes in design or

to make additions to or improvements in its products without imposing any

obligations upon itself to install them on its products previously manufac-

tured.

FOREWORD

The information contained in this service manual has been prepared for the professional automotive tech-

nician involved in daily repair operations. Information describing the operation and use of standard and

optional equipment is included in the Owner’s Manual provided with the vehicle.

Information in this manual is divided into groups. These groups contain description, operation, diagnosis,

testing, adjustments, removal, installation, disassembly, and assembly procedures for the systems and compo-

nents. To assist in locating a group title page, use the Group Tab Locator by clicking to the following page. The

first page of the group has a contents section that lists major topics within the group.

A Service Manual Comment form is included at the rear of this manual. Use the form to provide

DaimlerChrysler Corporation with your comments and suggestions.

Tightening torques are provided as a specific value throughout this manual. This value represents the

midpoint of the acceptable engineering torque range for a given fastener application. These torque values are

intended for use in service assembly and installation procedures using the correct OEM fasteners. When

replacing fasteners, always use the same type (part number) fastener as removed.

DaimlerChrysler Corporation reserves the right to change testing procedures, specifications, diagnosis,

repair methods, or vehicle wiring at any time without prior notice or incurring obligation.

GROUP TAB LOCATOR

Introduction

0Lubrication & Maintenance

2Suspension

3Driveline

5Brakes

7Cooling

8A Audio

8B Chime/Buzzer

8C Clock

8E Electronic Control Modules

8F Engine Systems

8G Heated Systems

8H Horn

8I Ignition Control

8J Instrument Cluster

8L Lamps

8M Message Systems

8N Power Systems

8O Restraints

8P Speed Control

8Q Vehicle Theft Security

8R Wipers/Washers

8W Wiring

9Engine

11 Exhaust System

13 Frame & Bumpers

14 Fuel System

19 Steering

21 Transaxle

22 Tires/Wheels

23 Body

24 Heating & Air Conditioning

25 Emissions Control

Service Manual Comment Forms (Rear of Manual)

NOTE: For New Vehicle Preparation

information, see the separate

publication, 81-170-00003.

INTRODUCTION

TABLE OF CONTENTS

page page

BODY CODE PLATES

DESCRIPTION ..........................1

FASTENER IDENTIFICATION

DESCRIPTION ..........................3

FASTENER USAGE

DESCRIPTION

DESCRIPTION - FASTENER USAGE ........6

DESCRIPTION - THREADED HOLE REPAIR . . 6

INTERNATIONAL VEHICLE CONTROL &

DISPLAY SYMBOLS

DESCRIPTION ..........................6

METRIC SYSTEM

DESCRIPTION ..........................7

TORQUE REFERENCES

DESCRIPTION ..........................9

VEHICLE IDENTIFICATION NUMBER

DESCRIPTION .........................10

VEHICLE SAFETY CERTIFICATION LABEL

DESCRIPTION .........................11

E-MARK LABEL

DESCRIPTION .........................11

VECI LABEL

DESCRIPTION .........................11

MANUFACTURE PLATE

DESCRIPTION .........................12

BODY CODE PLATES

DESCRIPTION

LOCATION AND DECODING

The Body Code Plate (Fig. 1) is located in the

engine compartment on the battery tray front side

(Fig. 2). There are seven lines of information on the

body code plate. Lines 4, 5, 6, and 7 are not used to

define service information. Information reads from

left to right, starting with line 3 in the center of the

plate to line 1 at the bottom of the plate.

BODY CODE PLATE LINE 3

DIGITS 1, 2, AND 3

Paint procedure

DIGIT 4

Open Space

DIGITS 5 THROUGH 7

Primary Paint (Refer to 23 - BODY/PAINT - SPEC-

IFICATIONS).

DIGIT 8 AND 9

Open Space

DIGITS 10 THROUGH 12

Secondary Paint

DIGIT 13 AND 14

Open Space

DIGITS 15 THROUGH 18

Interior Trim Code

DIGIT 19

Open Space

Fig. 1 BODY CODE PLATE

1 - PRIMARY PAINT

2 - SECONDARY PAINT

3 - VINYL ROOF

4 - VEHICLE ORDER NUMBER

5 - CAR LINE SHELL

6 - PAINT PROCEDURE

7 - ENGINE

8 - TRIM

9 - TRANSMISSION

10 - MARKET

11 - VIN

LH INTRODUCTION 1

DIGITS 20, 21, AND 22

Engine Code

•EER = 2.7 L, Six Cylinder, 24 Valve, DOHC,

Gasoline, Aluminum Block (MPI)

•EGG = 3.5 L, Six Cylinder, 24 Valve, SOHC,

High Output, Gasoline, Aluminum Block (MPI)

•EGK = 3.5 L, Six Cylinder, 24 Valve, SOHC,

High Output, Gasoline, Aluminum Block (MPI)

•EGJ = 3.5 L, Six Cylinder, 24 Valve, SOHC,

High Output, Gasoline, Aluminum Block

•EGC = 3.5 L, Six Cylinder, 24 Valve, SOHC,

Magnum, Gasoline, Aluminum Block

DIGIT 23

Open Space

BODY CODE PLATE – LINE 2

DIGITS 1 THROUGH 12

Vehicle Order Number

DIGITS 13, THROUGH 15

Vinyl Roof Code

DIGITS 16 AND 17

Open space

DIGITS 18 AND 19

Vehicle Shell Line

•LH

DIGITS 20

Carline

•C = Chrysler

•D = Dodge

•Y = Chrysler

DIGIT 21

Price Class

•E = Economy

•H = High Line

•L = Low Line

•M = Mid Line

•P = Premium

•S = Special/Sport

•X = Performance Image

DIGITS 22 AND 23

Body Type

•41 = Four Door Sedan

BODY CODE PLATE LINE 1

DIGITS 1, 2, AND 3

Transaxle Codes

•DGX = 42LE 4-Speed Electronic Automatic

Transaxle

DIGIT 4

Open Space

DIGIT 5

Market Code

•C = Canada

•B = International

•M = Mexico

•U = United States

DIGIT 6

Open Space

DIGITS 7 THROUGH 23

Vehicle Identification Number

•(Refer to VEHICLE DATA/VEHICLE INFOR-

MATION/VEHICLE IDENTIFICATION NUMBER -

DESCRIPTION) for proper breakdown of VIN code.

IF TWO BODY CODE PLATES ARE REQUIRED

The last code shown on either plate will be fol-

lowed by END. When two plates are required, the

last code space on the first plate will indicate (CTD)

When a second plate is required, the first four

spaces of each line will not be used due to overlap of

the plates.

Fig. 2 BODY CODE PLATE LOCATION

1 - BODY COPY PLATE

2 - BATTERY TRAY

2 INTRODUCTION LH

BODY CODE PLATES (Continued)

FASTENER IDENTIFICATION

DESCRIPTION

The SAE bolt strength grades range from grade 2

to grade 8. The higher the grade number, the greater

the bolt strength. Identification is determined by the

line marks on the top of each bolt head. The actual

bolt strength grade corresponds to the number of line

marks plus 2. The most commonly used metric bolt

strength classes are 9.8 and 10.9. The metric

strength class identification number is imprinted on

the head of the bolt. The higher the class number,

the greater the bolt strength. Some metric nuts are

imprinted with a single-digit strength class on the

nut face. Refer to the Fastener Identification and

Fastener Strength Charts (Fig. 3) and (Fig. 4).

LH INTRODUCTION 3

Fig. 3 FASTENER IDENTIFICATION

4 INTRODUCTION LH

FASTENER IDENTIFICATION (Continued)

Fig. 4 FASTENER STRENGTH

LH INTRODUCTION 5

FASTENER IDENTIFICATION (Continued)

FASTENER USAGE

DESCRIPTION

DESCRIPTION - FASTENER USAGE

WARNING: USE OF AN INCORRECT FASTENER

MAY RESULT IN COMPONENT DAMAGE OR PER-

SONAL INJURY.

Fasteners and torque specifications references in

this Service Manual are identified in metric and SAE

format.

During any maintenance or repair procedures, it is

important to salvage all fasteners (nuts, bolts, etc.)

for reassembly. If the fastener is not salvageable, a

fastener of equivalent specification must be used.

DESCRIPTION - THREADED HOLE REPAIR

Most stripped threaded holes can be repaired using

a Helicoilt. Follow the vehicle or Helicoiltrecommen-

dations for application and repair procedures.

INTERNATIONAL VEHICLE

CONTROL & DISPLAY

SYMBOLS

DESCRIPTION

The graphic symbols illustrated in the following

International Control and Display Symbols Chart

(Fig. 5) are used to identify various instrument con-

trols. The symbols correspond to the controls and dis-

plays that are located on the instrument panel.

Fig. 5 INTERNATIONAL CONTROL AND DISPLAY SYMBOLS

1 High Beam 13 Rear Window Washer

2 Fog Lamps 14 Fuel

3 Headlamp, Parking Lamps, Panel Lamps 15 Engine Coolant Temperature

4 Turn Warning 16 Battery Charging Condition

5 Hazard Warning 17 Engine Oil

6 Windshield Washer 18 Seat Belt

7 Windshield Wiper 19 Brake Failure

8 Windshield Wiper and Washer 20 Parking Brake

9 Windscreen Demisting and Defrosting 21 Front Hood

10 Ventilating Fan 22 Rear hood (Decklid)

11 Rear Window Defogger 23 Horn

12 Rear Window Wiper 24 Lighter

6 INTRODUCTION LH

METRIC SYSTEM

DESCRIPTION

The metric system is based on quantities of one,

ten, one hundred, one thousand and one million.

The following chart will assist in converting metric

units to equivalent English and SAE units, or vise

versa.

CONVERSION FORMULAS AND EQUIVALENT VALUES

MULTIPLY BY TO GET MULTIPLY BY TO GET

in-lbs x

0.11298 = Newton Meters

(N·m) N·m x 8.851 = in-lbs

ft-lbs x

1.3558 = Newton Meters

(N·m) N·m x

0.7376 = ft-lbs

Inches Hg (60° F) x 3.377 = Kilopascals (kPa) kPa x

0.2961 = Inches Hg

psi x 6.895 = Kilopascals (kPa) kPa x 0.145 = psi

Inches x 25.4 = Millimeters (mm) mm x

0.03937 = Inches

Feet x

0.3048 = Meters (M) M x 3.281 = Feet

Yards x

0.9144 = Meters M x

1.0936 = Yards

mph x

1.6093 = Kilometers/Hr.

(Km/h) Km/h x

0.6214 = mph

Feet/Sec x

0.3048 = Meters/Sec (M/S) M/S x 3.281 = Feet/Sec

mph x

0.4470 = Meters/Sec (M/S) M/S x 2.237 = mph

Kilometers/Hr. (Km/h) x

0.27778 = Meters/Sec (M/S) M/S x 3.600 Kilometers/Hr. (Km/h)

COMMON METRIC EQUIVALENTS

1 inch = 25 Millimeters 1 Cubic Inch = 16 Cubic Centimeters

1 Foot = 0.3 Meter 1 Cubic Foot = 0.03 Cubic Meter

1 Yard = 0.9 Meter 1 Cubic Yard = 0.8 Cubic Meter

1 Mile = 1.6 Kilometers

Refer to the Metric Conversion Chart to convert

torque values listed in metric Newton- meters (N·m).

Also, use the chart to convert between millimeters

(mm) and inches (in.) (Fig. 6).

LH INTRODUCTION 7

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Chrysler Automobil Handbücher

Chrysler

Chrysler 2014 Grand Cherokee Bedienungsanleitung

Chrysler

Chrysler 2009 Sebring Convertible Bedienungsanleitung

Chrysler

Chrysler SRT8 2012 Bedienungsanleitung

Chrysler

Chrysler Imperial Newport 1965 Bedienungsanleitung

Chrysler

Chrysler TOWN & COUNTRY 2009 Bedienungsanleitung

Chrysler

Chrysler All Vehicles 2013 Bedienungsanleitung

Chrysler

Chrysler 2005 Sebring Bedienungsanleitung

Chrysler

Chrysler Dodge Avenger 2013 Installationsanleitung

Chrysler

Chrysler Caravan 2005 Service-Handbuch

Chrysler

Chrysler pacifica hybrid 2017 Bedienungsanleitung

Chrysler

Chrysler Pacifica Hybrid 2022 Bedienungsanleitung

Chrysler

Chrysler Pacifica Hybrid 2020 Bedienungsanleitung

Chrysler

Chrysler Sebring Sedan Bedienungsanleitung

Chrysler

Chrysler 300 2018 Bedienungsanleitung

Chrysler

Chrysler 300 2010 Bedienungsanleitung

Chrysler

Chrysler 300 SRT 2019 Bedienungsanleitung

Chrysler

Chrysler Sebring Convertible Bedienungsanleitung

Chrysler

Chrysler GRAND CARAVAN 2023 Bedienungsanleitung

Chrysler

Chrysler 160 Gebrauchsanweisung

Chrysler

Chrysler Town and Country 2003 Bedienungsanleitung

Chrysler

Chrysler 2011 300 Limited Bedienungsanleitung

Chrysler

Chrysler 2005 Sebring Convertible Bedienungsanleitung

Chrysler

Chrysler Windsor C-60 1953 Bedienungsanleitung

Chrysler

Chrysler VOYAGER 2024 Bedienungsanleitung

Beliebte Automobil Handbücher anderer Marken

Toyota

Toyota 2000 Tundra Bedienungsanleitung

CITROËN

CITROËN DS4 DSign Bedienungsanleitung

Lexus

Lexus 2015 CT 200h Bedienungsanleitung

Cadillac

Cadillac CTS 2008 Bedienungsanleitung

Mercedes-Benz

Mercedes-Benz M-class ML 55 AMG Bedienungsanleitung

Porsche

Porsche Boxster S Bedienungsanleitung

GMC

GMC 2010 Savana 1500 Cargo Bedienungsanleitung

KIAM

KIAM SPORTAGE 2014 Stücklistenhandbuch

GMC

GMC 2013 Terrain Montageanleitung

GMC

GMC T-Series 1999 Bedienungsanleitung

Mercury

Mercury 1998 Mystique Bedienungsanleitung

Mercury

Mercury 2007 Mariner Bedienungsanleitung

Mazda

Mazda 2007 Mazdaspeed 3 Leitfaden

Mazda

Mazda 2014 CX-5 Bedienungsanleitung

GMC

GMC Chevrolet Express 2022 Bedienungsanleitung

GMC

GMC 1997 Jimmy Bedienungsanleitung

Chevrolet

Chevrolet 2012 Malibu Bedienungsanleitung

Cadillac

Cadillac 2010 Escalade Bedienungsanleitung