Maintenance
The strainer basket inthe filter tank should be inspected and cleaned at
1. Remove lid and lift out basket.
2. Remove debris and hose off with clean water if
3. Inspect the lid gasket, lubricate with
only if needed. If it is damaged, pls replace.
4. Replace the strainer.
5. Re-prime the filter tank.
6. Correctly locate the o-ring.
7. Replace the lid hand tighten
8. Switch on pump.
In c
limates where the pump may be
the
pump is protected from damage.It is
winter period it should be
the drain plug. Store it in a safe place when not use. An
filter tank basket.
When you a
re activate the pump ensure all seals ando
re-grease if necessary,
replace if unsure of condition.
Checkthat the motor shaft moves freely before re
1. When connecting electric cables tothe motor of the pump, be careful to correctly arrange
them inside the connection box, verifythat no bits of cable are l
See that the ground wire is correctly connected. When connecting the motor, follow the wiring
diagram supplied with the pump.
2. Be especially careful that no water enters the motor or electrical parts under voltage.
3. In
the event that the planned use is not as specified, adaptations and supplementary
technical rules may be necessary.
4. Before starting the pump, verifythe calibration of the electrical protection devices of the
motor and that
the protections against elec
positioned and attached.
5. It is advisable to follow the steps listed below before handling the pump in any way.
a) Turn off the voltage tothe pump.
b) Lock starting devices.
c) Verify that there is no voltage
in the circuits, including ancillary devices and auxiliary circuits.
d) Wait until motor stops completely.
The above list should be considered indicative and not binding for the purpose of safety,
specific safety
rules may exist in particular regulations.
Assembly Instructions (some parts may be pre
F
ollow the step below and the corresponding diagrams for assembly.
Step 1.
Place the strainer basket tothe strainer housing. Be sure that the opening the basket is
aligned with the opening in the
The strainer basket inthe filter tank should be inspected and cleaned at
2. Remove debris and hose off with clean water if
necessary.
3. Inspect the lid gasket, lubricate with
silicon based grease
only if needed. If it is damaged, pls replace.
limates where the pump may be
exposed to frost or freezing,c
are must be taken to ensure
pump is protected from damage.It is
recommended
that ifthe pump is not used during
and store pump in a
dry location. Do not replace
the drain plug. Store it in a safe place when not use. An
example would be store plug in the
re activate the pump ensure all seals ando
-
rings are in operational condition,
replace if unsure of condition.
Checkthat the motor shaft moves freely before re
-activation.
1. When connecting electric cables tothe motor of the pump, be careful to correctly arrange
them inside the connection box, verifythat no bits of cable are l
eft inside the box on closing it.
See that the ground wire is correctly connected. When connecting the motor, follow the wiring
2. Be especially careful that no water enters the motor or electrical parts under voltage.
the event that the planned use is not as specified, adaptations and supplementary
4. Before starting the pump, verifythe calibration of the electrical protection devices of the
the protections against elec
trical and mechanical contacts are correctly
5. It is advisable to follow the steps listed below before handling the pump in any way.
a) Turn off the voltage tothe pump.
in the circuits, including ancillary devices and auxiliary circuits.
d) Wait until motor stops completely.
The above list should be considered indicative and not binding for the purpose of safety,
rules may exist in particular regulations.
Assembly Instructions (some parts may be pre
-assembled)
ollow the step below and the corresponding diagrams for assembly.
Place the strainer basket tothe strainer housing. Be sure that the opening the basket is
are must be taken to ensure
that ifthe pump is not used during
dry location. Do not replace
example would be store plug in the
rings are in operational condition,
1. When connecting electric cables tothe motor of the pump, be careful to correctly arrange
eft inside the box on closing it.
See that the ground wire is correctly connected. When connecting the motor, follow the wiring
2. Be especially careful that no water enters the motor or electrical parts under voltage.
the event that the planned use is not as specified, adaptations and supplementary
4. Before starting the pump, verifythe calibration of the electrical protection devices of the
trical and mechanical contacts are correctly
5. It is advisable to follow the steps listed below before handling the pump in any way.
in the circuits, including ancillary devices and auxiliary circuits.
The above list should be considered indicative and not binding for the purpose of safety,
Place the strainer basket tothe strainer housing. Be sure that the opening the basket is
5
