Circuit-test DMR-6550 Bedienungsanleitung
USER'S MANUAL
Multimeter
True RMS Auto ranging
DMR-6550
CIRCUIT-TEST ELECTRONICS
www.circuittest.com
- 2 -
Introduction
Safety
This meter measures AC/DC Voltage, AC/DC Current, Resistance,
Capacitance, Frequency, Diode Test, Continuity plus Thermocouple
Temperature. Proper use and care of this meter will provide many years of
reliable service.
This symbol adjacent to another symbol, terminal or operating
device indicates that the operator must refer to an explana-
tion in the Operating Instructions to avoid personal injury or
damage to the meter.
This WARNING symbol indicates a potentially hazardous
situation, which if not avoided, could result in death or serious
injury.
This CAUTION symbol indicates a potentially hazardous situ-
ation, which if not avoided, may result damage to the product.
This symbol advises the user that the terminal(s) so marked
must not be connected to a circuit point at which the voltage
with respect to earth ground exceeds (in this case) 500 VAC
or VDC.
This symbol adjacent to one or more terminals identies them
as being associated with ranges that may, be subjected to
particularly hazardous voltages. For maximum safety, the meter
and test leads should not be handled when these terminals
are energized.
Double Insulation.
- 3 -
SAFETY INFORMATION
Caution and proper guidelines must be followed for personal and product safety.
Read this instruction manual carefully and completely before using the meter.
Lack of caution or poor safety practices can result in serious injury or death.
• Always start with power off. Set the function switch to the correct setting
before making any measurements and do not change position of the func-
tion switch during measurements.
• Do not use the meter if the meter or test leads look damaged or if there is
doubt that the meter is not operating properly.
• When using the test probes always keep ngers behind the nger guards.
Never touch the exposed probe tip.
• Always consider circuits to be energized. Never assume any equipment
to be de-energized.
• Use caution when working above 35VDC or 25VAC RMS as these volt-
ages pose a shock hazard.
• Never connect unit to AC or DC powered circuits when the function switch
is set to resistance, diode check or continuity ranges.
• Always disconnect the power when performing resistance, or diode tests.
• Always turn off the power to the circuit under test before unsoldering or
breaking the circuits. Small amount of current can be dangerous.
• Disconnect test leads before removing the batteries or the fuse.
• Do not operate the unit unless the case is completely closed.
- 4 -
SAFETY INSTRUCTIONS
This meter has been designed for safe use, but must be operated with caution.
The rules listed below must be carefully followed for safe operation.
1. NEVER apply voltage or current to the meter that exceeds the specied
maximum:
Input Limits
Function Maximum Input
V DC or V AC 1000VDC/VAC
A DC/AC 10A DC/AC (30 seconds max every
15 minutes)
Frequency, Resistance,
Capacitance, Duty Cycle, Diode
test, Continuity
600V DC/AC rms
Temperature 600V DC/AC rms
2. USE EXTREME CAUTION when working with high voltages.
3. NEVER connect the meter leads across a voltage source while the
function switch is in the current, resistance, or diode mode. Doing so
can damage the meter.
4. ALWAYS discharge lter capacitors in power supplies and disconnect
the power when making resistance or diode tests.
5. ALWAYS turn off the power and disconnect the test leads before open-
ing the covers to replace the fuse or batteries.
6. NEVER operate the meter unless the back cover and the battery and
fuse covers are in place and fastened securely.
- 5 -
Controls and Jacks
1. 6000 count LCD Display
2. Function switch
3. 10A (positive) input jack
4. COM (negative) input jack
5. Positive input jack
6. HOLD & Backlight button
7. Max/Min button
8. Range/ /Diode button
9. Hz/% button
Continuity
Low Battery
Diode
HOLD Data Hold
AUTO AutoRanging
AC Alternating Current or Voltage
DC Direct Current or Voltage
Symbols and Annunciators
- 6 -
Specications
Display: 6000 counts LCD display.
Polarity: Automatic, (-) negative polarity indication.
Input Impedance: 7.8MΩ
Overrange: “OL” mark indication.
AC Response: True RMS
Low battery indication: “ ” is displayed if the battery voltage drops below
operating voltage.
Measurement rate: 2 times per second, nominal.
Auto power off: Automatically shuts down after approx. 15 minutes
of inactivity.
Operating Temperature: 0ºC to 50ºC (32ºF to 122ºF) at < 70 % relative
humidity.
Storage temperature: -20ºC to 60ºC (-4ºF to 140ºF) at < 80 % relative
humidity.
Fuse: 10A/250V Fuse, Fast blow 5x20mm
Battery: One 9V, NEDA 1604 battery.
Dimensions: 150 (H) x 70 (W) x 48 (D) mm
Weight: Approx.: 255g
Enclosure: Double molded
Safety / Approvals: This meter is UL and CUL approved and con-
forms to IEC61010-1 for Overvoltage Category
CAT III 600V and CAT II 1000V.
- 7 -
DC Voltage
Range Resolution Accuracy
600.0mV 0.1mV ±0.5% of reading ± 2 digits
6.000V 1mV
±1.2% of reading ± 2 digits60.00V 10mV
600.0V 100mV
1000V 1V ±1.5% of reading ± 2 digits
AC Voltage
Range Resolution Accuracy
6.000V 1mV ±1.5% of reading ± 10 digits
60.00V 10mV ±1.5% of reading ± 10 digits
600.0V 100mV
1000V 1V ±2.0% of reading ± 10 digits
DC Current
Range Resolution Accuracy
6A 1mA ±2.5% of reading ± 5 digits
10A 10mA
Overload Protection: 10A / 250V Fuse.
Note: Accuracy is given at 18ºC to 28ºC (65ºF to 83ºF), < 70 % RH
AC Current
Range Resolution Accuracy
6A 1mA ±3.0% of reading ± 5 digits
10A 10mA
- 8 -
Resistance
Range Resolution Accuracy
600.0Ω 0.1Ω ±1.2% of reading ± 4 digits
6.000kΩ 1Ω ±1.0% of reading ± 2 digits
60.00kΩ 10Ω ±1.2% of reading ± 2 digits
600.0kΩ 100Ω
6.000MΩ 1kΩ ±2.0% of reading ± 2 digits
60.00MΩ 10kΩ ±5.0% of reading ± 10 digits
Capacitance (Auto-ranging)
Range Resolution Accuracy
40.00nF 10pF ±5.0% of reading ± 50 digits
400.0nF 0.1nF ±3.0% of reading ± 5 digits
±3.0% of reading ± 5 digits
4.000uF 1nF
40.00uF 10nF
400.0uF 0.1uF ±5.0% of reading ± 5 digits
4000uF 1uF ±5.0% of reading ± 5 digits
Frequency (Auto-ranging)
Range Resolution Accuracy
9.999Hz 0.001Hz ±1.5% of reading ± 5 digits
99.99Hz 0.01Hz
999.9Hz 0.1Hz
±1.2% of reading ± 3 digits
9.999kHz 1Hz
99.99kHz 10Hz
999.9kHz 100Hz
10MHz 1kHz ±1.5% of reading ± 4 digits
Sensitivity: >0.5V RMS while ≤1MHz;
Sensitivity: >3V RMS while >1MHz
- 9 -
Duty Cycle
Range Resolution Accuracy
0.1%~99.9% 0.1% ±1.2% of reading ± 2 digits
Pulse width: >100us, <100ms;
Frequency width: 5Hz – 150 kHz
Sensitivity: >0.5V RMS
Temperature
Range Resolution Accuracy
-20ºC~+760ºC 1ºC ±3% of reading ±5ºC/9ºF
-4ºF~+1400 ºF 1ºF
Sensor: Type K Thermocouple
Diode Test
Range Resolution Accuracy
0.3mA typical 1 mV ±10% of reading ± 5 digits
Open circuit voltage: 1.5V dc typical
Audible continuity
Audible threshold: Less than 100Ω Test current: <0.3mA
- 10 -
Operating Instructions
Autoranging/Manual Range Selection
1. Press the RANGE key. The “AUTO” display indicator will turn off.
2. Press the RANGE key to step through the available ranges until you
select the range you want.
3. To exit Manual Ranging, press and hold RANGE key for 2 seconds.
WARNING: Risk of electrocution. High-voltage circuits, both AC and DC,
are very dangerous and should be measured with great care.
1. ALWAYS turn the function switch to the OFF position when the meter
is not in use. This meter automatically shuts OFF after 15 minutes of
inactivity.
2. If “OL” appears in the display during a measurement, the value exceeds
the range you have selected. Change to a higher range.
NOTE: On some low AC and DC voltage ranges, with the test leads not con-
nected to a device, the display may show a random, changing reading. This
is normal and is caused by the high-input sensitivity. The reading will stabilize
and give a proper measurement when connected to a circuit.
When the meter is rst turned on, it automatically goes into Autoranging. This
automatically selects the best range for the measurements being made and is
generally the best mode for most measurements. For measurement situations
requiring that a range be manually selected, perform the following:
NOTE: Manual ranging does not apply for Capacitance, Frequency functions.
Inhaltsverzeichnis
Andere Circuit-test Multimeter Handbücher
Circuit-test
Circuit-test DMR-6500 Bedienungsanleitung
Circuit-test
Circuit-test DMR-4200 Bedienungsanleitung
Circuit-test
Circuit-test DCL-280 Bedienungsanleitung
Circuit-test
Circuit-test DCL-620 Bedienungsanleitung
Circuit-test
Circuit-test DMR-4350 Bedienungsanleitung
Circuit-test
Circuit-test DMR-1500 Bedienungsanleitung
Circuit-test
Circuit-test DCL-420 Bedienungsanleitung
Circuit-test
Circuit-test DMR-2400 Bedienungsanleitung
Circuit-test
Circuit-test DMR-1100 Bedienungsanleitung
Circuit-test
Circuit-test DMR-6600 Bedienungsanleitung
Beliebte Multimeter Handbücher anderer Marken
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Bedienungsanleitung
PeakTech
PeakTech 4000 Gebrauchs- und Pflegehandbuch
YOKOGAWA
YOKOGAWA 90050B Bedienungsanleitung
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung
Fluke
Fluke 8846A Bedienungs- und Wartungshandbuch
Tempo Communications
Tempo Communications MM200 Bedienungsanleitung
