Circutor EHome Link Bedienungsanleitung

eHome Link

INSTALLATION GUIDE

(M354A01-03-22C)

eHome Link

2Installation Guide

eHome Link

Installation Guide

Revision log

Date Revision Description

02/22 M354A01-03-22A Initial Version

06/22 M354A01-03-22B Changes in the following sections:

2.- 3.- 5.C.- 5.G.- 5.H.- 5.J.- 5.K.- 5.L.- 6.- 7.

07/22 M354A01-03-22C Changes in the following sections:

5.F.- 5.H.- 5.I.

Disclaimer

CIRCUTOR S.A.U. reserves the right to make modifications to the device or the unit specifications set

out in this instruction manual without prior notice.

CIRCUTOR S.A.U. on its web site, supplies its customers with the latest versions of the device speci-

fications and the most updated manuals.

www.circutor.com

eHome Link

4Installation Guide

eHome Link

Installation Guide

This document is copyrighted, 2022 by CIRCUTOR S.A.U. All rights are reserved. CIRCUTOR S.A.U.

reserves the right to make improvements to the products described in this manual at any time without

notice.

No part of this manual can be reproduced, copied, translated or transmitted in any form or by any means

without the prior written permission of the original manufacturer. Information provided in this manual is

intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for

its use, or for any infringements upon the rights of third parties at hat may result from its use.

All other product names or trademarks are properties of their respective owners.

eHome Link

Installation Guide

Here’s your guide

to install eHome

Link

Disclaimer .............................................................................................................................................. 3

Revision log ........................................................................................................................................... 3

Here’s your guide to install eHome Link .......................................................................................... 5

1.- So, hello! ........................................................................................................................................... 6

2.- Before the installation ................................................................................................................... 8

3.- Overview ......................................................................................................................................... 10

4.- Dimensions .................................................................................................................................... 12

5.- Installation ......................................................................................................................................14

A.- Space Requirements .............................................................................................................. 15

B.- Opening the unit ..................................................................................................................... 16

C.- Power Supply line and Data connection ............................................................................ 18

D.- Positioning ...............................................................................................................................20

E.- Fixing ......................................................................................................................................... 21

F.- Electrical Installation .............................................................................................................. 22

G.- Power Supply Line connection .............................................................................................23

H.- Current Limit Selector ..............................................................................................................24

I.- Unique CirBEON (Optional) ....................................................................................................25

J.- Remote Control Function ........................................................................................................28

K.- Data Modbus RS485 Connection ..........................................................................................29

L.- Closing the Charge Point .......................................................................................................30

M.- Verification............................................................................................................................... 31

6.- Technical Data ............................................................................................................................... 32

7.- Modbus register map ................................................................................................................... 34

Need help ? ......................................................................................................................................... 37

Guarantee ............................................................................................................................................ 37

eHome Link

6Installation Guide

eHome Link

Installation Guide

So, hello!

This manual provides commissioning information about eHome Link, which has been

designed and tested to allow electric vehicle charging according to IEC 61851-1:2017.

This document has different sections such as step-by-step installation procedure and

technical data.

THE FOLLOWING SYMBOLS ARE USED FOR IMPORTANT

SAFETY INFORMATION IN THIS DOCUMENT

ELECTRIC RISK

Take precautions to make the electrical connection inside the unit.

Unit must be disconnected from any power source during commissioning.

ATTENTION!

Indicates that the damage to property can occur if appropriate precautions

are not taken.

• Complies with IEC 61851, Electric vehicle conductive charging system (IEC 61851-

1:2017 and IEC 61851-21-2:2018)

• Complies with IEC 62196, Plugs, socket-outlets, vehicle couplers and vehicle

inlets (IEC 62196-1 and IEC 62196-2).

• Directives: 2014/35/UE, LVD;2014/30/UE, EMC.

eHome Link

8Installation Guide

Refer to TECHNICAL DATA section for more information about environmental installation conditions.

Read carefully all the instructions before starting in order to ensure

properly installation of the Charge Point.

IMPORTANT SAFETY INSTRUCTIONS

The Charge Point is designed for installation in indoor and outdoor areas. For each of the different

conditions of installation, the unit shall be installed safely and assuring the adequate protections.

• Charge Point must not be installed in areas

where potential risk of explosions are.

• Do not install the Charge Point where

falling objects may damage the device.

• The Charge Point can be installed in

locations with non-restricted access.

• The surface where the Charge Point is

placed must withstand the mechanical

forces.

• This device shall not be used for any other

purpose than electric vehicle charging

modes as specified in IEC 61851.

• Do not modify this device. If modified,

CIRCUTOR will reject all responsibility and

the warranty will be void.

• The Charge Point does not support the

ventilation optional function described in

IEC 61851-1:2017 (clause 6.3.2.2)

• Do not use any adapter, except those

approved by the EV manufacturer. Adapter

only allowed to eHome Link models with

socket-outlet.

• Do not perform any repair or manipulation

of the unit while it is energized.

• Only trained and qualified personnel should

be able to access to low voltage electrical

parts inside the unit.

• Check the installation annually by qualified

technician.

• Remove from service any item which have

a fault that could be dangerous for users

(broken plugs, caps that don’t close...).

• Use only CIRCUTOR supplied spare parts.

• Do not use this product if the enclosure or

the EV connector is broken, cracked, open,

or shows any other indication of damage.

eHome Link

Installation Guide

ELECTRICAL WIRING CONSIDERATIONS

Take into consideration this section before start wiring connections

of the Charge Point.

1 — ELECTRICAL PROTECTIONS

The Charge Point may not include elements of electrical protection.

If this equipment has internal electrical protections, they are installed in each socket-outlet

for the protection of the user against an electrical failure, according to the international

standard IEC 61851-1:2017.

In order to guarantee the total protection of the users and the installation (power supply line

included) in front of any electrical hazard, it is mandatory to install a (MCB) Miniature Circuit

Breaker and a (RCD) Residual Current Device upstream of the Charge Point.

These electrical protections and the rest of the installation have to be aligned with the local

and national rules. The selectivity of the protections has to be guaranteed at all times.

2 — POWER SUPPLY LINE DIMENSIONING

The dimensioning of the input power supply line of the Charge Point must be checked by

a qualified electrician. Note that various factors such as cable length between distribution

board and the Charge Point or the maximum output current of the Charge Point may

influence the criteria of cable selection.

3 — MAXIMUM OUTPUT CURRENT

Please refer to the TECHNICAL DATA section to consult the default factory settings for

maximum output current of the Charge Point.

If the maximum output current the Charge Point can deliver exceeds the maximum current

that can be provided by the installation, the Charge Point maximum current limit should be

adjusted following the guidelines included in this manual. Refer to Current Limit Selector

section for more information.

Refer to TECHNICAL DATA section for more information about environmental installation conditions.

Before the installation

eHome Link

10 Installation Guide

SHORT DESCRIPTION

eHome Link is specially designed to be easily installed both in outdoor and indoor private

car parks, and to be compatible with all the EV models of the market according to European

standard IEC 61851-1, by just plugging your car.

What’s included:

Installation

Guide

Charge Point

eHome Link

Guía de instalación

Andere Handbücher für eHome Link

Inhaltsverzeichnis

Andere Circutor Akkuladegerät Handbücher

Circutor

Circutor URBAN Bedienungsanleitung

Circutor

Circutor Raption 50 Series Bedienungsanleitung

Circutor

Circutor Wallbox ePark Bedienungsanleitung

Circutor

Circutor URBAN WB DC Series Bedienungsanleitung

Circutor

Circutor WB-eBasic T2C32 Benutzerhandbuch

Circutor

Circutor Wallbox eNext Series Bedienungsanleitung

Circutor

Circutor eHome T1C16 Bedienungsanleitung

Circutor

Circutor eHome Series Bedienungsanleitung

Circutor

Circutor Raption 150 Series Bedienungsanleitung

Circutor

Circutor eHome Series Bedienungsanleitung

Circutor

Circutor URBAN M11 Bedienungsanleitung

Circutor

Circutor Raption 150C Series Bedienungsanleitung

Circutor

Circutor Raption Series Bedienungsanleitung

Circutor

Circutor eHome Link Bedienungsanleitung

Circutor

Circutor RAPTION 160C Series Bedienungsanleitung

Circutor

Circutor URBAN WB Series Bedienungsanleitung

Circutor

Circutor URBAN WB Series Bedienungsanleitung

Circutor

Circutor WB-eBasic T2S32 Benutzerhandbuch

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung