Circutor CDP series Beilage

APPLICATION NOTES
Connection and conguration of a
CDP with KOSTAL inverters
(M028E0401-03-19A)

2
CDP
Application notes

3
Application notes
CDP
SAFETY PRECAUTIONS
DANGER
Warns of a risk, which could result in personal injury or material damage.
ATTENTION
Indicates that special attention should be paid to a speci c point.
Follow the warnings described in this manual with the symbols shown below.
If you must handle the unit for its installation, start-up or maintenance, the following
should be taken into consideration:
Incorrect handling or installation of the unit may result in injury to personnel as well as damage
to the unit. In particular, handling with voltages applied may result in electric shock, which may
cause death or serious injury to personnel. Defective installation or maintenance may also
lead to the risk of re.
Read the manual carefully prior to connecting the unit. Follow all installation and maintenance
instructions throughout the unit’s working life. Pay special attention to the installation stan-
dards of the National Electrical Code.
Refer to the instruction manual before using the unit
In this manual, if the instructions marked with this symbol are not respected or carried out correctly, it can
result in injury or damage to the unit and /or installations.
CIRCUTOR, SA reserves the right to modify features or the product manual without prior noti cation.
DISCLAIMER
CIRCUTOR, SA reserves the right to make modi cations to the device or the unit speci ca-
tions set out in this instruction manual without prior notice.
CIRCUTOR, SA on its web site, supplies its customers with the latest versions of the device
speci cations and the most updated manuals.
www.circutor.com
CIRCUTOR, recommends using the original cables and accessories that are
supplied with the device.

4
CDP
Application notes
CONTENTS
SAFETY PRECAUTIONS ��������������������������������������������������������������������������������������������������������������������������������������� 3
DISCLAIMER ���������������������������������������������������������������������������������������������������������������������������������������������������������� 3
CONTENTS������������������������������������������������������������������������������������������������������������������������������������������������������������� 4
REVISION LOG������������������������������������������������������������������������������������������������������������������������������������������������������� 5
SYMBOLS��������������������������������������������������������������������������������������������������������������������������������������������������������������� 5
1�- INTRODUCTION������������������������������������������������������������������������������������������������������������������������������������������������ 6
2�- KOSTAL PIKO INVERTER�������������������������������������������������������������������������������������������������������������������������������� 7
2�1�- COMMUNICATION CABLE����������������������������������������������������������������������������������������������������������������������� 7
2�1�1� CONNECTION OF ONE INVERTER ���������������������������������������������������������������������������������������������������� 8
2�1�2� CONNECTION OF SEVERAL INVERTERS����������������������������������������������������������������������������������������� 8
2�2�- INVERTER COMMUNICATION CONFIGURATION���������������������������������������������������������������������������������� 8
2�2�1� COMMUNICATION BETWEEN THE INVERTER AND THE PC BY ETHERNET CABLE ���������������� 10
2�2�2� CONFIGURATION ������������������������������������������������������������������������������������������������������������������������������ 10
3�- CDP CONFIGURATION����������������������������������������������������������������������������������������������������������������������������������� 12
4�- COMMUNICATIONS TEST AND REGULATION �������������������������������������������������������������������������������������������� 14
4�1�- COMMUNICATIONS TEST���������������������������������������������������������������������������������������������������������������������� 14
4�2�- REGULATION TEST�������������������������������������������������������������������������������������������������������������������������������� 15
5�- MAINTENANCE AND TECHNICAL SERVICE������������������������������������������������������������������������������������������������ 16
6�- GUARANTEE��������������������������������������������������������������������������������������������������������������������������������������������������� 16

5
Application notes
CDP
REVISION LOG
Table 1: Log of revisions.
Date Revision Description
10/14 M028E0401-03-14A Original version
09/19 M028E0401-03-19A Change in the following sections:
1. - 2.1. - 2.2. - 2.2.2. - 3.
Note: The images of the units are solely for the purpose of illustration and may differ from the
original unit.
SYMBOLS
Table 2:Symbols.
Symbol Description
In compliance with the relevant European directive.
Device covered by European directive 2012/19/EC. At the end of its useful life, do not
leave the unit in a household waste container. Follow local regulations on electronic equip-
ment recycling.
DC current
~AC current

6
CDP
Application notes
1�- INTRODUCTION
KOSTAL offers several inverter models that can be managed via the CDP Dynamic power con-
troller, specically they are:
PIKO IQ 4�2-10
PIKO 10-20
PIKO 36 EPC
For the CDP controller to be able to correctly manage the inverter, communication between the
two devices must be correct and both products must be correctly programmed.
These application notes are not meant as a substitute for the CDP or
inverter manuals, but rather as additional support for individuals who
need to interconnect the two devices.
Even so, the guides and manuals of each product should be consulted and each company is
responsible for providing technical support.
An inverter from the KOSTAL PIKO family of inverters will be used as the model in these ap-
plication notes.
NOTE: Images and information on the inverter are taken from the ofcial documents and manuals pro-
vided by the manufacturer.
NOTE: The test has been conducted using the KOSTAL PIKO 10.1 inverter, s.n.90391MEF00014,
HW:040350 SW:04.03

7
Application notes
CDP
2�- KOSTAL PIKO INVERTER
The CDP and the inverter communicate via an RS-485 bus. This RS-485 bus can connect up
to 32 inverters, although the number of inverters in the vast majority of domestic installations
ranges from 1 to 3.
2.1.- COMMUNICATION CABLE
To communicate with a KOSTAL PIKO inverter using a CDP, the inverter must be equipped
with a communications card with an RS-485 interface (Figure 1).
Figure 1:Communication card.
Table 3:Communication card.
No Description
1Connection terminal S0/AL-Out (2-pole)
22 Ethernet connections (RJ45)
3Analog interface connection terminal
4Connection terminal for RS-485 interface
5Extension module connection terminal
The connector is a terminal for a 0.25mm2cable
Functions of the communication cable terminals between the CDP and the inverter:
Table 4: Functions of the communication cable terminals.
CDP
R2 channel communications
connector
Communication card
RS-485 Terminal (No. 4)
Terminal Description Terminal Description
1 A+ A+ RS-485 A +
3 B- B- RS-485 B -
5 GND GND GND
It is not necessary to wire the GND terminal, although it is advisable to do so for long distances.

8
CDP
Application notes
2�1�1� CONNECTION OF ONE INVERTER
Figure 2 shows the connection between the CDP and a single inverter.
Figure 2:Connection between a CDP and a single inverter.
2�1�2� CONNECTION OF SEVERAL INVERTERS
Figure 3 shows the connection between the CDP and several inverters.
Figure 3:Connection between a CDP and several inverters.
The communication cable between the inverters must have the following conguration Table 5:
Table 5:Communications cable connection.
Inverter 1 cable
end
Inverter 3 cable
end
Inverter n cable
end
A A A
B B B
GND GND GND
2.2.- INVERTER COMMUNICATION CONFIGURATION
The following describes how to use the display to congure the inverter for ensuring correct
communication with the CDP.
The AC and DC sides of the inverter must be connected to the mains before
it can turn on.
Consult the inverter manual if you have any doubts.
The web server or the display (only for type II communications card) can be used for congur-
ing any parameter in the KOSTAL inverter.

9
Application notes
CDP
The front panel display may vary according to the inverter model, Figure 4 and Figure 5.
Figure 4:PIKO 3.0/3.6/4.2/5.5 screen (with type I communications card)
Figure 5:PIKO 7.0/8.3/10.1/10/12/15/17/20 screen (with type II communications card )
Programming the inverter on the web server is recommended, given that it streamlines the pro-
gramming and enables a faster and easier conguration.
The parameters to be congured are:
Peripheral number
KOSTAL communication protocol
Analogue input function.
The communications speed is 19200 bps, a xed parameter.
When a KOSTAL inverter is selected in the CDP, the device adjusts the communication speed
to the inverters’ speed.

10
CDP
Application notes
2�2�1� COMMUNICATION BETWEEN THE INVERTER AND THE PC BY ETHERNET CABLE
The KOSTAL inverter is equipped with a web server that can be accessed using the IP address
shown on the display of the unit.
To view the IP address, follow the instructions below:
1�- Press the button in the main menu until the inverter icon appears shaded, as shown in
Figure 6.
Figure 6:Main menu screen.
2�- Press “Enter”
3�- Press the button until you reach the “Communication” option. Press “Enter”.
4�- Press the button until you reach the “Network 2 Conguration” option. Press “Enter”.
This window shows the current IP address of the inverter.
See the chapter on how to access the web server in the inverter manual.
2�2�2� CONFIGURATION
The following values must be programmed in the web server, Figure 7:
Peripheral number: enter the number 1 (if there is 1 inverter) and consecutive numbers
following 1 (if there are several inverters).
Communication protocol: select KOSTAL
Baud rate: select 19200
Bus Termination: select if it is a single inverter. In the case of having a several inverters
chain as shown in Figure 3, select for the last inverter.
Analogue input function the “Sensors” option must be selected for this variable
Andere Handbücher für CDP series
2
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Circutor Controller Handbücher

Circutor
Circutor computer max 6f Bedienungsanleitung

Circutor
Circutor CDP series Beilage

Circutor
Circutor Computer SMART III FAST 6 Bedienungsanleitung

Circutor
Circutor Computer SMART III FAST 12Vdc Bedienungsanleitung

Circutor
Circutor CDP Beilage

Circutor
Circutor computer MAX 6 Bedienungsanleitung

Circutor
Circutor CDP series Beilage

Circutor
Circutor FastComp 12rt Bedienungsanleitung

Circutor
Circutor Computer SMART III 6 Bedienungsanleitung

Circutor
Circutor max 12f Bedienungsanleitung

















