Cisco NM-1E2W Kurzanleitung

Doc. No.

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA

Cisco Systems, Inc.

Corporate Headquarters

WAN Card Slot Network Module

Conﬁguration Note

Product Numbers:

NM-1E2W, NM-2E2W, NM-1E1R2W

CPANM-1E2W, CPANM-2E2W, CPANM-1E1R2W

This document provides information about the following network modules for the Cisco 3600 series

of modular access routers:

•1-Ethernet 2-WAN card slot network module, Cisco product number NM-1E2W or

CPANM-1E2W. (See Figure 1.) This module will also be referred to as the 1E 2-slot network

module.

•2-Ethernet 2-WAN card slot network module, Cisco product number NM-2E2W or

CPANM-2E2W. (See Figure 2.) This module will also be referred to as the 2E 2-slot network

module.

•1-Ethernet1-Token Ring 2-WANcardslotnetworkmodule,CiscoproductnumberNM-1E1R2W

or CPANM-1E1R2W. (See Figure 3.) This module will also be referred to as the 1E1R 2-slot

network module.

Unless speciﬁcally identiﬁed, references to 2-slot network modules in this conﬁguration note and

other publications include all three network modules.

Each 2-slot network module provides one or two LAN interfaces, plus two slots for optional WAN

interface cards. For information on WAN interface cards, see the card’s conﬁguration note.

78-3637-01

2WAN Card Slot Network Module Conﬁguration Note

Figure 1 1-Ethernet 2-WAN Card Slot Network Module

Figure 2 2-Ethernet 2-WAN Card Slot Network Module

Figure 3 1-Ethernet 1-Token Ring 2-WAN Card Slot Network Module

Use this document in conjunction with your router installation and conﬁguration guide and the

Regulatory Compliance and Safety Information document for your router. If you have questions or

need help, refer to the section “Obtaining Service and Support” later in this document for further

information.

1E

2WW1

ETHERNET 0

AUI

ACT

LNK

LEDs Enable

LED

10BaseT

port AUI

port

H7215

Key for BRI WAN

interface cards

2E

2WW1

STP

ETHERNET 0ETHERNET 1

AUI

ACT

LNK

ACT

ILNK

LEDs

Key for BRI WAN

interface cards 10BaseT

port

10BaseT 

port LEDs Enable

LED

AUI port

H7213

1E

1R W1

STP

ETHERNET 0

AUI

ACT

LNK

TOKEN RING 0

16MBPS

IN-RING

Token Ring 

interface LEDs 10BaseT

port

STP port UTP port Ethernet

LEDs

AUI port

H6555

Key for BRI WAN

interface cards

WAN Card Slot Network Module Configuration Note 3

Software Requirements

This document contains the following sections:

•Software Requirements, page 3

•Safety Recommendations, page 3

•Required Tools and Equipment, page 6

•Installing a 2-Slot Network Module in a Chassis Slot, page 6

•Network Module Connectors, page 8

•Connecting Ethernet Ports, page 10

•Connecting Token Ring Ports, page 13

•WAN Card Slot Module LEDs, page 14

•Conﬁguring the LAN Interfaces, page 15

•Obtaining Service and Support, page 21

•Cisco Connection Online, page 21

Warning Only trained and qualiﬁed personnel should be allowed to install or replace this

equipment. (To see translated versions of this warning, refer to the Regulatory Compliance and

Safety Information document that accompanied the router.)

Warning Before working on a chassis or working near power supplies, unplug the power cord on

AC units; disconnect the power at the circuit breaker on DC units. (To see translated versions of this

warning,refertotheRegulatoryComplianceandSafetyInformationdocumentthataccompaniedthe

router.)

Warning Ultimate disposal of this product should be handled according to all national laws and

regulations. (To see translated versions of this warning, refer to the Regulatory Compliance and

Safety Information document that accompanied the router.)

Caution To avoid damaging electrostatic discharge (ESD)-sensitive components, ensure that you

have discharged all static electricity from your body before opening the chassis. Before performing

procedures described in this document, review the section “Safety Recommendations” later in this

document.

Software Requirements

The minimum version of Cisco Internetwork Operating System (Cisco IOS) software needed for

2-slot network modules is 11.1(6)AAS.

Safety Recommendations

Follow these guidelines to ensure general safety:

•Keep the chassis area clear and dust-free during and after installation.

•Put the removed chassis cover in a safe place.

•Keep tools away from walk areas where you or others could fall over them.

4WAN Card Slot Network Module Conﬁguration Note

Safety Recommendations

•Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf and roll

up your sleeves.

•Wear safety glasses when working under any conditions that might be hazardous to your eyes.

•Do not perform any action that creates a potential hazard to people or makes the equipment

unsafe.

Warning The Ethernet 10BaseT, Token Ring, serial, console, and auxiliary ports contain safety

extra-low voltage (SELV) circuits. BRI circuits are treated like telephone-network voltage (TNV)

circuits. Avoid connecting SELV circuits to TNV circuits. (To see translated versions of this

warning,refertotheRegulatoryComplianceandSafetyInformationdocumentthataccompaniedthe

router.)

Warning Network hazardous voltages are present in the BRI cable. If you detach the BRI cable,

detach the end away from the router ﬁrst to avoid possible electric shock. Network hazardous

voltages also are present on the system card in the area of the BRI port (RJ-45 connector), regardless

of when power is turned off. (To see translated versions of this warning, refer to the Regulatory

Compliance and Safety Information document that accompanied the router.)

Warning The ISDN connection is regarded as a source of voltage that should be inaccessible to

user contact. Do not attempt to tamper with or open any public telephone operator (PTO)-provided

equipment or connection hardware. Any hardwired connection (other than by a nonremovable,

connect-one-time-only plug) must be made only by PTO staff or suitably trained engineers. (To see

translated versions of this warning, refer to the Regulatory Compliance and Safety Information

document that accompanied the router.)

Safety with Electricity

Warning Before workingon equipment that is connected to power lines, removejewelry(including

rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and

can cause serious burns or weld the metal object to the terminals. (To see translated versions of this

warning,refertotheRegulatoryComplianceandSafetyInformationdocumentthataccompaniedthe

router.)

Follow these guidelines when working on equipment powered by electricity:

•Locate the emergency power-OFF switch in the room in which you are working. Then, if an

electrical accident occurs, you can quickly shut the power OFF.

•Before working on the router, turn OFF the power and unplug the power cord.

•Disconnect all power before doing the following:

—Installing or removing a router chassis

—Working near power supplies

•Do not work alone if potentially hazardous conditions exist.

WAN Card Slot Network Module Configuration Note 5

Safety Recommendations

Warning Before opening the chassis, disconnect the telephone-network cables to avoid contact

with telephone-network voltages. (To see translated versions of this warning, refer to the Regulatory

Compliance and Safety Information document that accompanied the router.)

Warning Do not work on the system or connect or disconnect cables during periods of lightning

activity. (To see translated versions of this warning, refer to the Regulatory Compliance and Safety

Information document that accompanied the router.)

•Never assume that power is disconnected from a circuit. Always check.

Warning Do not touch the power supply when the power cord is connected. For systems with a

power switch, line voltages are present within the power supply even when the power switch is OFF

and the power cord is connected. For systems without a power switch, line voltages are present

within the power supply when the power cord is connected. (To see translated versions of this

warning,refertotheRegulatoryComplianceandSafetyInformationdocumentthataccompaniedthe

router.)

•Look carefully for possible hazards in your work area, such as moist ﬂoors, ungrounded power

extension cables, and missing safety grounds.

•If an electrical accident occurs, proceed as follows:

—Use caution; do not become a victim yourself.

—Turn OFF power to the router.

—If possible, send another person to get medical aid. Otherwise, determine the condition of the

victim and then call for help.

—Determine if the person needs rescue breathing or external cardiac compressions; then take

appropriate action.

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when

electronic printed circuit cards are improperly handled and can result in complete or intermittent

failures. Always follow ESD prevention procedures when removing and replacing cards. Ensure that

the router chassis is electrically connected to earth ground. Wear an ESD-preventive wrist strap,

ensuring that it makes good skin contact. Connect the clip to an unpainted surface of the chassis

frame to safely channel unwanted ESD voltages to ground. To properly guard against ESD damage

and shocks, the wrist strap and cord must operate effectively. If no wrist strap is available, ground

yourself by touching the metal part of the chassis.

Caution For safety, periodically check the resistance value of the antistatic strap, which should be

between 1 and 10 megohms (Mohm).

6WAN Card Slot Network Module Conﬁguration Note

Required Tools and Equipment

You need the following tools and equipment to install a network module in a Cisco 3600 series

chassis slot:

•Network module

•Number 1 Phillips screwdriver or small ﬂat-blade screwdriver

•ESD-preventive wrist strap

Installing a 2-Slot Network Module in a Chassis Slot

Caution Network modules do not support online insertion and removal (hot swap). To avoid

damaging the module, before you insert a network module into a chassis slot, you must turn OFF

electrical power and disconnect network cables.

The following instructions apply only to installing network modules in a chassis slot. To install a

WAN interface card in a network module, see the conﬁguration note for the WAN interface card.

You can install network modules in the chassis either before or after mounting the router, whichever

is more convenient.

Follow this procedure to install a network module:

Step 1 Turn OFF electrical power to the router. However, to channel ESD voltages to ground, do

not unplug the power cable. Remove all network interface cables, including telephone

cables, from the rear panel.

The following warning applies to routers that use a DC power supply:

Warning Before performing any of the following procedures, ensure that power is removed from

the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that

services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of

the circuit breaker in the OFF position. (To see translated versions of this warning, refer to the

Regulatory Compliance and Safety Information document that accompanied the router.)

Step 2 Using either a number 1 Phillips screwdriver or a small ﬂat-blade screwdriver, remove the

blank ﬁller panel from the chassis slot where you plan to install the module. Save the

blank panel for future use.

Step 3 Align the network module with the guides in the chassis and slide it gently into the slot.

(See Figure 4.)

WAN Card Slot Network Module Configuration Note 7

Installing a 2-Slot Network Module in a Chassis Slot

Figure 4 Installing a Module in a Router

Step 4 Push the module into place until you feel its edge connector mate securely with the

connector on the motherboard.

Step 5 Fasten the module’s captive mounting screws into the holes in the chassis, using the

Phillips or ﬂat-blade screwdriver.

Step 6 If the router was previously running, reinstall the network interface cables and turn ON

power to the router.

The following warning applies to routers that use a DC power supply:

Warning After wiring the DC power supply, remove the tape from the circuit breaker switch handle

and reinstate power by moving the handle of the circuit breaker to the ON position. (To see translated

versions of this warning, refer to the Regulatory Compliance and Safety Information document that

accompanied the router.)

Blank Network Module Panels

If the router is conﬁgured with fewer than four network modules, make sure that blank panels ﬁll the

open chassis slots to provide proper airﬂow. (See Figure 5.)

Figure 5 Blank Network Module Panel

Module

Router

H7481

INPUT 100-240VAC 50/60HZ 3.0-1.5 AMPS

2E

2W W1

ETHERNET 1 ETHERNET 0

AUI

ACT

LNK

ACT

LNK

ACT

SERIAL

BRI

NT1

B1

NT1

SEE MANUAL BEFORE INSTALLATION

2E

2W W1

AUI

ACT

LNK

ACT

LNK

BRI

S/T

B1

DO NOT INSTALL WAN INTERFACE

CARDS WITH POWER APPLIED

ETHERNET 1 ETHERNET 0

H6552

8WAN Card Slot Network Module Conﬁguration Note

Network Module Connectors

Blank WAN Interface Card Panels

If the 2-slot network module is conﬁgured with fewer than two WAN interface cards, make sure that

blank panels ﬁll the open base module slots to provide proper airﬂow. (See Figure 6.)

Figure 6 Blank WAN Interface Card Panel

Network Module Connectors

The number and type of connectors on a 2-slot network module depend on the type of module.

1E 2-Slot Network Module

The 1E 2-slot network module has one Ethernet attachment unit interface (AUI) DB-15 connector

and one 10BaseT RJ-45 connector. (See Figure 7.) Only one of these two connectors can be active

at a time. The active port is identiﬁed in software by port type (Ethernet), the module’s slot number,

and port number 0.

The module detects the type of network connection automatically, and you do not need to select the

media type in software. If cables are plugged into both ports, the 10BaseT connection is selected.

Figure 7 1E 2-Slot Network Module

2E 2-Slot Network Module

The 2E 2-slot network module has ports for two Ethernet connections. (See Figure 8.)

Ethernetport 0 uses either theAUI (DB-15)connector on theright or the10BaseT (RJ-45) connector

in the center, but only one at a time. Ethernet port 1 uses the 10BaseT connector on the left. This port

does not provide an AUI connector. Ports are identiﬁed in software by port type (Ethernet), the

module’s slot number, and the port number.

The module detects the type of network connection automatically, and you do not need to select the

media type in software. If cables are plugged into both ports, the 10BaseT connection is selected.

DO NOT INSTALL WAN INTERFACE

CARDS WITH POWER APPLIED

H6649

1E

2WW1

ETHERNET 0

AUI

ACT

LNK

LEDs Enable

LED

10BaseT

port AUI

port

H7215

Key for BRI WAN

interface cards

WAN Card Slot Network Module Configuration Note 9

Network Module Connectors

Figure 8 2E 2-Slot Network Module

1E1R 2-Slot Network Module

The 1E1R 2-slot network module has ports for one Ethernet connection and one Token Ring

connection. (See Figure 9.)

The Ethernet port (Ethernet 0) uses either the AUI (DB-15) connector or the 10BaseT (RJ-45)

connector, but only one at a time. The Token Ring port (Token Ring 0) uses either the shielded

twisted-pair (STP) connector or the unshielded twisted-pair (UTP) connector, but only one at a time.

Ports are identiﬁed in software by port type (Ethernet or Token Ring), the module’s slot number, and

the port number.

The module detects the type of network connection automatically, and you do not need to select the

media type in software. If cables are plugged into both Ethernet ports, the 10BaseT connection is

selected.

Figure 9 1E1R 2-Slot Network Module

2E

2W W1

ETH 1 ETH 0

ACT

LNK

ACT

LNK

SERIAL

BRI

NT1

B1

NT1

H6556

1E

1R W1

STP

ETHERNET 0

AUI

ACT

LNK

TOKEN RING 0

16MBPS

IN-RING

Token Ring 

interface LEDs 10BaseT

port

STP port UTP port Ethernet

LEDs

AUI port

H6555

Key for BRI WAN

interface cards

10 WAN Card Slot Network Module Conﬁguration Note

Connecting Ethernet Ports

On 1-Ethernet network modules and on Ethernet port 0 (the right-hand port) of 2-Ethernet network

modules, connect either the Ethernet AUI or the 10BaseT connector, but not both at the same time.

Ethernet port 1 (the left-hand port) of 2-Ethernet network modules provides only a 10BaseT

connector.

AUI ConnectionsUse an Ethernet AUI cable to connect the AUI port on an Ethernet network module to an Ethernet

transceiver. The female end of the AUI cable mates with the slide-latch connector of the transceiver

cable. (See Figure 10.)

Figure 10 Connecting an Ethernet AUI Port to a Transceiver

If the transceiver cable has thumbscrew connectors, you can connect it directly to the AUI port by

replacing the AUI port slide latch with a jackscrew (provided in a separate bag).

10BaseT Connections

Use an Ethernet 10BaseT cable to connect the 10BaseT port on an Ethernet network module to a hub

or other network device. Figure 11 shows the 10BaseT port on an Ethernet network module

connected to a hub.

2E

2WW1

STP

ETHERNET 0

ETHERNET 1

AUI

ACT

LNK

ACT

ILNK

H7437

Ethernet AUI port (DB-15)

(with jackscrews or slide-latch)

Ethernet AUI cable 

(not supplied) Ethernet

transceiver

BNC connector

To thin Ethernet network To thin Ethernet network

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Steuereinheit Handbücher

Cisco

Cisco NM-1CT1 Kurzanleitung

Cisco

Cisco ASA5506-AP702 Bedienungsanleitung

Cisco

Cisco NCS 1004 Bedienungsanleitung

Cisco

Cisco PA-VXA Series Bedienungs- und Wartungsanleitung

Cisco

Cisco NCS 1010 Merkblatt

Cisco

Cisco Catalyst 3110G Handbuch

Cisco

Cisco Firepower 4110 Bedienungsanleitung

Cisco

Cisco Catalyst 5000 Series Bedienungsanleitung

Cisco

Cisco EHWIC-3G-EVDO Bedienungsanleitung

Cisco

Cisco 6015 Gebrauchs- und Pflegehandbuch

Cisco

Cisco MEM-NP8F Series Kurzanleitung

Cisco

Cisco ONS 15200 Bedienungsanleitung

Cisco

Cisco Catalyst 9400 Series Installations- und Betriebshandbuch

Cisco

Cisco 3110 Bedienungsanleitung

Cisco

Cisco C3850-NM-4-1G Bedienungsanleitung

Cisco

Cisco 7300-1OC12POS-MM Bedienungs- und Wartungsanleitung

Cisco

Cisco TelePresence Touch10 Bedienungsanleitung

Cisco

Cisco Firepower 4112 Handbuch

Cisco

Cisco SCE8000 GBE Bedienungsanleitung

Cisco

Cisco T1 Bedienungsanleitung

Cisco

Cisco TelePresence MCU 4200 Series Bedienungsanleitung

Cisco

Cisco MEM-CIP-64M Bedienungsanleitung

Cisco

Cisco FlexWAN Bedienungsanleitung

Cisco

Cisco GS7000 Betriebsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung