Cisco IP DECT 6800 Series Handbuch

Hardware Installation

•Installation Requirements, on page 1

•Install the Base Station, on page 5

•Mount the Base Station on the Ceiling, on page 6

•Mount the Base Station on a Desk, on page 9

•Mount the Base Station on the Wall, on page 10

•Install the Battery in the Handset, on page 13

•Set Up the Charging Cradle, on page 16

•Charge the Handset Battery, on page 17

Installation Requirements

The Cisco IP DECT 6800 Series is made up of the following hardware:

• Cisco IP DECT Phone 6825 Handset

• Cisco IP DECT Phone 6825 Ruggedized Handset

• Cisco IP DECT 210 Multi-Cell Base Station

Before you begin to set up the Cisco IP DECT 6800 Series system:

• Determine the number of users (handsets) that are required.

• Determine the number of phone lines (numbers) that are required. Each user can have up to 2 lines and

2 concurrent calls.

• Given the number of handsets, determine the number of base stations required, based on:

• Estimated simultaneous handset usage

You can have up to 30 handsets registered on each base station. However, the number of active

calls the base station can handle is limited by the codec.

Hardware Installation

Table 1: Codec and Number of Active Handsets Supported

Number of Active CallsCodecBand

10 calls for single base station

configuration

8 calls for multicell

configuration (see note)

G.711

G.726

Narrowband

5G.722

OPUS

Wideband

If a user turns on Push to Talk, the base station can only support 6 active calls

with the narrowband codec and 3 calls with the wideband codec.

Note

The single cell and multicell deployments have different maximum numbers of handsets and base

stations. The following table describes the limits.

Table 2: Maximum Handsets and Base Stations in Single Cell and Multicell Configurations

MulticellSingle CellHardware

2501Base stations

1000 SIP registrations30Handsets

For information on network configurations, see Single Cell and Multicell Networks, on page 3.

• Size of the space to be covered.

• Range of the base stations. Each base station has a range of up to 984 feet (300 meters) outdoors

and a range of 164 feet (50 meters) indoors.

• The call control system must be set up and operational. Obtain the call control system information,

including server addresses, user ids, and passwords. You may find Worksheets useful when you collect

the information.

• Plan the location to install each base station.

• Determine if you need to mount the base stations on walls or on the ceiling.

We provide wall plugs and screws to mount the base station on drywall (plasterboard), but your

surface may require a different fastening system.

•Ensure that there is a LAN connection close to the planned location of each base station. The Ethernet

cable included with the base is 78.5 inches (200 cm) but you can use any length of straight-through

CAT5e cable.

• If you do not use Power over Ethernet (PoE), ensure that there is an electrical outlet close to the

planned location of each base station. The length of the power cord with the adapter is 82 inches

(208 cm).

Hardware Installation

Installation Requirements

• Determine that the base stations are placed so that handsets can communicate. Make sure that the

coverage is optimal for your users.

With the Cisco IP DECT 210 Multi-Cell Base Station, you can add additional base stations to

improve coverage.

Related Topics

Mount the Base Station on the Wall, on page 10

Mount the Base Station on the Ceiling, on page 6

Single Cell and Multicell Networks

Based on the information collected in Installation Requirements, on page 1, you set up either a single cell

system or a multicell system.

A single cell system consists of one base station with up to 30 handsets. The following diagram shows a single

cell network.

Figure 1: Single Cell Network

A multicell system consists of several base stations with each handling up to 30 handsets. The following

diagram shows a multicell network with 3 base stations.

Hardware Installation

Single Cell and Multicell Networks

Figure 2: Multicell Network

Base Station Package Contents

Your base station package has the following contents:

• Base station

• Base station stand

• Ethernet cable

• Regional power adapter

• USB-to-power jack cable

• Mounting screws and plugs

• Printed compliance document

If you want to mount the base station on the ceiling, you need to order a separate ceiling mount kit.

Power Requirements

The base station requires one of these power sources:

• Power over Ethernet (PoE) - minimum IEEE 802.3: Power class 2 (3.84 – 6.49W)

• Power adapter specific to your region with a USB-to-power jack cable. The power adapter is plugged

into an electrical outlet.

The handset is powered by a 3.7V, 1000mAh, 4.1Wh, Lithium ion battery.

The handset charger power cable plugs into the regional power adapter, and the power adapter must be plugged

into an electrical outlet.

Hardware Installation

Base Station Package Contents

Install the Base Station

When the base station connects to the network, the LEDs light to indicate the network status:

• Green—Connected.

• Amber—Connection in progress.

• Red, flashing—Can't connect to the network.

• Red, solid—Network connection resetting.

Use this procedure to check that the base station and the network can communicate with each other, before

you mount the base station in the chosen location.

Before you begin

The base station requires:

• Power over Ethernet (PoE) or a power adapter

• LAN connection

• An IP address assigned by DHCP in the network

Procedure

Step 1 Plug one end of the Ethernet cable into the base station.

Step 2 Plug the other end of the Ethernet cable into the LAN port.

Step 3 If you don't use PoE, plug the power adapter into the base station and then into the electrical outlet.

Step 4 If the LED flashes red after a few minutes, do these steps:

a) Locate the Reset button on the bottom edge of the base station.

b) Press and hold Reset until the LED is a solid red.

c) Release Reset.

The LED should flash amber and then try to connect. If the LED doesn't light green, then the base station

can't get an IP address. See Base Station LED is Solid Red for further help.

What to do next

Mount the base station with one of these procedures:

•Mount the Base Station on the Ceiling, on page 6

•Mount the Base Station on a Desk, on page 9

•Mount the Base Station on the Wall, on page 10

Hardware Installation

Install the Base Station

Mount the Base Station on the Ceiling

You can mount the base station on a ceiling. The base station has a custom ceiling mount bracket that you

can install on the ceiling. You need to order the ceiling mount bracket.

Figure 3: Ceiling Mount Bracket

Each base station has a range of up to 984 feet (300 meters).

In this task, the term device means the base station.

Before you begin

You need:

• Ceiling mount bracket

• Pencil

• Mounting hardware (screws and plugs) suitable for the ceiling construction.

• LAN connection close to the mounting location.

• If you do not use PoE, a power outlet close to the mounting location.

• Ensure that the base station can communicate with the network (see Install the Base Station, on page

5). After it can communicate and the LED is green, you can unplug the cables.

Determine the best placement, taking into account the coverage area and the building construction materials.

You may need to install addition base stations for best coverage.

You can use the site survey tool on the handset to plan placement.

Procedure

Step 1 Hold the ceiling mount bracket in the desired location.

Step 2 Mark the screw placement.

Hardware Installation

Mount the Base Station on the Ceiling

Step 3 Install the plugs as described by the manufacturer.

Step 4 Install the screws through the bracket and into the plugs.

Step 5 Connect the Ethernet cable to the device and route the cable through the slot in the device.

Step 6 Plug the power adapter into the device and route the cable through the slot in the device.

Step 7 Align the slots in the bracket with the slots in the device and turn left until the device locks in place.

This graphic shows the alignment of the mounting bracket to the base station.

Hardware Installation

Mount the Base Station on the Ceiling

This diagram shows the way you turn the device to lock it into the mounting bracket.

Step 8 Plug the Ethernet cable into the LAN port.

Hardware Installation

Mount the Base Station on the Ceiling

Step 9 If required, plug the power adapter into the electrical outlet.

What to do next

Configure the Base Station

Mount the Base Station on a Desk

You can place the base station on a desk or other horizontal surface (for example, a book shelf). Select a

location where the base station won't be easily knocked off.

Each base station has a range of up to 984 feet (300 meters).

In this task, the term device means the base station.

Before you begin

You need:

• LAN connection close to the mounting location.

• If you do not use PoE, a power outlet close to the mounting location.

• Ensure that the base station can communicate with the network (see Install the Base Station, on page

5). After it can communicate and the LED is green, you can unplug the cables if you haven't tested the

base station in the final location.

Determine the best placement, taking into account the coverage area and the building construction materials.

You may need to install addition base stations for best coverage.

You can use the site survey tool on the handset to plan placement.

Procedure

Step 1 Connect the Ethernet cable to the device and route the cable through the slot in the device.

Step 2 If required, plug the power adapter into the device and route the cable through the slot in the device.

Step 3 Slide the stand into the device and press it until it clicks into place.

This graphic shows the stand connection to the base station.

Hardware Installation

Mount the Base Station on a Desk

Step 4 Plug the Ethernet cable into the LAN port.

Step 5 If required, plug the power adapter into the electrical outlet.

What to do next

Configure the Base Station

Mount the Base Station on the Wall

You can mount the base station on a wall. You put two screws into the wall and slip the base station onto the

screw heads or you can use the ceiling mount bracket.

We recommend that you mount the base station as high as possible on a wall. If possible, mount it at a

downward facing angle for better radio coverage.

Each base station has a range of up to 984 feet (300 meters).

In this task, the term device means the base station.

Before you begin

You need:

• Pencil

• Level

• Tape measure

• Mounting hardware (screws and wall plugs) suitable for the wall construction. You can also use the

ceiling mount bracket.

• LAN connection close to the mounting location.

• If you do not use PoE, a power outlet close to the mounting location.

Hardware Installation

Mount the Base Station on the Wall

Andere Handbücher für IP DECT 6800 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Schnurloses Telefon Handbücher

Cisco

Cisco 6800 Series Bedienungsanleitung

Cisco

Cisco Webex 840 Bedienungsanleitung

Cisco

Cisco Webex 840 Bedienungsanleitung

Cisco

Cisco 6800 Series Bedienungsanleitung

Cisco

Cisco 6800 Series Handbuch

Cisco

Cisco 78 Series Bedienungsanleitung

Cisco

Cisco Small Business Pro SPA 504G Bedienungsanleitung

Cisco

Cisco 860 Series Bedienungsanleitung

Cisco

Cisco Webex 860 Bedienungsanleitung

Cisco

Cisco IP DECT 6800 Series Bedienungsanleitung

Cisco

Cisco Webex Wireless Phone 800 Series Betriebsanleitung

Cisco

Cisco 6800 Series Bedienungsanleitung

Cisco

Cisco Webex 840 Bedienungsanleitung

Cisco

Cisco 860 Series Bedienungsanleitung

Cisco

Cisco Webex Wireless Phone 800 Series Handbuch

Cisco

Cisco 840 Bedienungsanleitung

Cisco

Cisco Webex Wireless Phone 840 Bedienungsanleitung

Cisco

Cisco SPA 232 Bedienungsanleitung

Cisco

Cisco Webex 800 Series Bedienungsanleitung

Cisco

Cisco 8821 Betriebsanleitung

Cisco

Cisco 6800 Series Betriebsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung