Cisco CE 2000 Platform SCE 2000 4xGBE Bedienungsanleitung

QUICK START GUIDE

Cisco Service Control Engine 2000 4xGBE QUICK START GUIDE,

RELEASE 3.8.X

1Preparing for Installation

2Rack-Mounting the SCE 2000 Chassis

3Connecting Power Supply Units

4Connecting Management Interfaces and Performing Initial System Configuration

5Cabling Line Ports

6Completing the Installation

7Troubleshooting

8Obtaining Documentation and Submitting a Service Request

Revised: September 17, 2012, OL-26789-01

Note This document supports all 3.8.x releases.

1 Preparing for Installation

This section contains warnings, tools and part information, and site preparation details.

Warning

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any

equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for

preventing accidents.

Warning

Only trained and qualified personnel should install, replace, or service this equipment.

Warning

Read the installation instructions before you connect the system to its power source.

Warning

This unit is intended for installation in restricted access areas. A restricted access area is where access can only

be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is

controlled by the authority responsible for the location.

Warning

Voltage is present on the backplane when the system is operating. To reduce risk of an electric shock, keep hands

and fingers out of the power supply bays and backplane areas.

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Warning

Before you begin the installation of the SCE 2000 platform, read the Regulatory Compliance and Safety Information

for the Cisco Service Control Engines (SCE) document.

Site Preparation

•Print out and have accessible the “Cisco SCE 2000 GBE Installation Checklist”, found in the Cisco SCE 2000 GBE

Installation and Configuration Guide, to record information about this installation.

•Verify that the power service at the site is suitable for the SCE 2000 chassis.

•Verify that there is at least a two inch (5 cm) clearance on both sides of the SCE 2000 and five inches (12.7 cm) at the rear

for adequate airflow for the inlet and exhaust vents.

Tools and Parts

Use the following list of tools and parts as a checklist for preparing to install the SCE 2000 chassis:

•Number 1 and number 2 Phillips screwdrivers

•1/4-inch flat-blade screwdriver

•Tape measure and level

•Masking tape or some other method of marking the desired installation height in the rack

•1/4-inch hex wrench

•Grounding kit (shipped with SCE 2000)

•12 AWG or 2.5 mm copper installation wire with hex or loop connectors for DC power leads (DC power only) Ring

terminals must be UL approved and suitable for 12 AWG wire.

•AC power cords (AC power only, shipped with SCE 2000)

•Rack-mounting kit (shipped with SCE 2000)

–

Spare screws for changing bracket position

Unpacking the Cisco SCE 2000

Tip When you unpack the Cisco SCE 2000, do not discard the shipping container. Flatten the shipping cartons and store

them with the pallet. You may need these containers if you move or ship the Cisco SCE 2000 in the future.

Check the contents of the shipping container:

•Check the contents of the accessories kit against the list of accessories in the “Cisco SCE 2000 Component List” in the Cisco

SCE 2000 Installation and Configuration Guide and the packing slip. Verify that you received all listed equipment, which

should include the following:

–

Hardware and software documentation, if ordered

–

Optional equipment that you ordered, such as network interface cables, transceivers, or special connectors

Installing the SCE 2000 on a Workbench or Tabletop

You can install the SCE 2000 platform on any flat surface (Figure 1) as long as the surface is large enough for the SCE 2000,

and allows for adequate airflow and ventilation around the sides of the SCE 2000. When installing the SCE 2000 on a

workbench or tabletop or in a rack, ensure that the surface is clean and in a safe location.

Figure 1 Installing the System on a Flat Surface

LINKRX

Cisco SCE 2000

Series

4xGBE

RXMMT

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

GBE-1

SUBLINENET

PWRB ST

TUS

PWRA BYP

ASS

10/100/

1000

LINK/

ACTIVE

10/100/

1000

LINK/

ACTIVE

GBE-2

SUBLINE/CASCADENET

AUX

CONSOLE

MNG 2

MNG 1

92782

Step 1 Remove the adhesive strips from the four rubber feet and affix the feet onto the four marked locations on the bottom

panel of the unit

Step 2 Place the SCE 2000 platform on the tabletop or workbench.

2 Rack-Mounting the SCE 2000 Chassis

This chapter provides information for rack-mounting the SCE 2000 chassis.

Warning

Before you install, operate, or service the system, read the Regulatory Compliance and Safety Information for the

Cisco Service Control Engines (SCE). This guide contains important safety information you should know before

working with the system.

SCE 2000 Mounting Brackets

There are two standard types of equipment racks, and the appropriate brackets for each are provided in the enclosed kit.

•19” rack with front rack posts — the mounting kit includes two mounting brackets as illustrated below:

Figure 2 Mounting Brackets

•19” rack with front and back rack posts — in addition to the mounting brackets illustrated below, the mounting kit includes

two crossrail supports that the unit slides onto.

Figure 3 Crossrail Supports

The SCE 2000 mounts to the two front rack posts with brackets that attach to the front of the SCE 2000. The inside width

between the two posts or mounting strips (left and right) must be at least 17.3 inches (44 cm).

Note Remember to leave a two-inch (5 cm) clearance on both sides of the SCE 2000 and at the rear for adequate airflow for

the inlet and exhaust vents.

210429

210430

Attaching Brackets to the SCE 2000

Before installing the SCE 2000 in the rack, you must first install an appropriate rack-mount bracket on each side of the front

of the SCE 2000, as illustrated in the following figures.

Figure 4 Attaching the Mounting Brackets (4-post)

Figure 5 Attaching the Mounting Brackets (2-post)

Before installing the SCE 2000 in the rack, you must first install a rack-mount bracket on each side of the front of the SCE 2000.

To install the rack-mount brackets on the SCE 2000 chassis, complete the following steps:

Step 1 Align the rack-mount bracket to the side of the SCE 2000. Choose the proper bracket for your installation (2-post rack

or 4-post rack) as illustrated in SCE 2000 Mounting Brackets

Step 2 Insert and tighten three screws.

Step 3 Repeat steps 1 and 2 on the other side of the SCE 2000.

If mounting the SCE 2000 in a rack with only two posts, skip to Mounting the System to the Rack, page 8.

If mounting the SCE 2000 in a rack with four posts, proceed to the next step, Installing the Crossrail Supports (Four-post rack

only), page 7.

LINKRX

Cisco SCE 2000

Series

4xGBE

RXMMTX

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

GBE-1

SUBLINENET

PWRB ST

TUS

PWRA BYP

ASS

10/100/

1000

LINK/

ACTIVE

10/100/

1000

LINK/

ACTIVE

GBE-2

SUBLINE/CASCADENET

AUX

CONSOLE

MNG2

MNG1

1 2

92780

LINKRX

Cisco SCE 2000

Series

4xGBE

RXMMTX

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

GBE-1

SUBLINENET

PWRB ST

TUS

PWRA BYP

ASS

10/100/

1000

LINK/

ACTIVE

10/100/

1000

LINK/

ACTIVE

GBE-2

SUBLINE/CASCADENET

AUX

CONSOLE

MNG2

MNG1

1 2

210431

Installing the Crossrail Supports (Four-post rack only)

This section provides information for assembling the crossrail supports and attaching them to the rack.

When mounting in a rack with four posts (front and back) the two crossrail supports are mounted one on each side of the rack.

The SCE 2000 then slides into these crossrails, which support the weight of the unit.

Assembling the Crossrail Supports

Step 1 Assemble the two crossrail supports. Use three screws for each crossrail assembly.

Figure 6 Assembling the Slider Brackets

Step 2 Make sure that they are oriented so that both crossrails will support the SCE 2000 when they are attached to the rack.

Attaching the Crossrail Supports to the Rack

Step 1 Align the crossrail supports with the side of the rack, parallel to the floor.

Figure 7 Attaching the Crossrails to the Rack

Step 2 Insert and tighten two screws to the front posts or mounting strips of the rack

Step 3 Insert and tighten two screws to the back posts of the rack.

Step 4 Repeat steps 2 and 3 on the other side of the rack, keeping the brackets flush against the posts and parallel to the

supporting bracket on first side of the rack.

321

92777

321

92778

Mounting the System to the Rack

When the appropriate mounting brackets are securely installed, the SCE 2000 can be installed into the rack.

Caution Make sure that the rack brakes are locked or that the rack is otherwise stabilized.

Step 1 Slide the SCE 2000 into the rack, pushing it back until the brackets (installed at the front of the unit) meet the mounting

strips or posts on both sides of the rack.

Figure 8 Sliding the SCE Platform into the Rack

A rack with both front and back posts will have the crossrail supports installed. Slide the SCE 2000 onto these crossrails

and push it all the way back.

LINKRX

CiscoSCE2000

Series

4xGBE

RXMMTX

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

GBE-1

SUBLINENET

PWRBST

TUS

PWRABYP

ASS

10/100/

1000

LINK/

ACTIVE

10/100/

1000

LINK/

ACTIVE

GBE-2

SUBL

INE/CASCADENET

AUX

CONSOLE

MNG2

MNG1

LINKRX

Cisco SCE 2000

Series

4xGBE

RXMMTX

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

GBE-1

SUBL

INENET

PWRB ST

TUS

PWRA BYP

ASS

10/100/

1000

LINK/

ACTIVE

10/100/

1000

LINK/

ACTIVE

GBE-2

SUBLINE/CASCADENET

AUX

CONSOLE

MNG2

MNG1

1 2 3

92781

Step 2 While keeping the brackets flush against the posts or mounting strips, align the holes in the brackets with the holes on

the rack or mounting strip. Insert and tighten two appropriate screws to the rack for each bracket.

Figure 9 Securing the SCE Platform to the Rack

Note Since the brackets support the weight of the entire SCE 2000 chassis, be sure to use all four screws to fasten the

two rack-mount brackets to the rack posts.

LINKRX

Cisco SCE 2000

Series

4xGBE

RXMMTX

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

LINKRXTX

RXMMTX

GBE-1

SUBLINENET

PWRB ST

TUS

PWRA BYP

ASS

10/100/

1000

LINK/

ACTIVE

10/100/

1000

LINK/

ACTIVE

GBE-2

SUBLINE/CASCADENET

AUX

CONSOLE

MNG2

MNG1

321

92779

3 Connecting Power Supply Units

The SCE 2000 platform is shipped with the power supplies (AC or DC) already installed. This section provides information for

grounding the SCE 2000 platform and connecting the AC or DC power supply units.

Connecting Chassis Ground

Figure 10 Grounding the Unit (AC)

Figure 11 Grounding the Unit (DC)

A grounding kit is provided with each SCE 2000. Use this grounding kit to properly ground the SCE 2000 chassis.

BYPASS 2

IN POWER B OK IN POWER A OK

BYPASS 1

92766

BYPASS 2

IN POWER B OK IN POWER A OK

BYPASS 1

210601

Andere Handbücher für CE 2000 Platform SCE 2000 4xGBE

Inhaltsverzeichnis

Andere Cisco Motor Handbücher

Cisco

Cisco SCE 1000 and Bedienerhandbuch

Beliebte Motor Handbücher anderer Marken

Rotax

Rotax 125 senior MAX evo Bedienungsanleitung

Kohler

Kohler K361 Bedienungsanleitung

MTD

MTD OHV Series Bedienungsanleitung

Kohler

Kohler COMMAND CH18-745 Bedienungsanleitung

Mercury

Mercury D4.2L D-Tronic Bedienungsanleitung

Selve

Selve SE Plus-RC Series Bedienungsanleitung

Perkins

Perkins 1206E-E66TA Bedienungsanleitung

Skov

Skov DA 174 Handbuch

Rossi

Rossi TX11 Series Bedienungsanleitung

Siemens

Siemens SIMOTICS T-1FW3 Merkblatt

AL-KO

AL-KO PRO 350 Bedienungsanleitung

MTU

MTU 12 V 4000 Lx4 Bedienungsanleitung

Nanni

Nanni N3.30 Gebrauchsanweisung

Nanni

Nanni N5.160 CR2 Bedienungsanleitung

KSB

KSB SuPreme Series Montageanleitung

Hiwin

Hiwin EM1 Series Bedienungsanleitung

Rotax

Rotax 912 i series Betriebsanleitung

Siemens

Siemens SIMOTICS XP 1MB1 Bedienungsanleitung