Cisco ASA 5585-X Bedienungsanleitung

Cisco Systems, Inc. www.cisco.com

Cisco ASA 5585-X Quick Start Guide

Last Updated: April 1, 2015

1. Package Contents

This section lists the package contents of each chassis. Note that contents are subject to change, and your exact

contents might contain additional or fewer items.

Note: The ASA 5585-X with SSP-10, SSP-20, or SSP-40 ships with one power supply module installed and one

power cable. The ASA 5585-X with SSP-60, ships with two power supply modules installed and two power

cables.

2. Power On the ASA

1. Attach the power cable to the back of the ASA. If you have redundant power supplies, you must connect both

power cables to the back of the chassis.

PWR

BOOT

ALARM

ACT

VPN

PS1

HDD1

PS0

HDD0

USB

RESET

SFP1 SFP01

7MGMT

AUX CONSOLE

PWR

BOOT

ALARM

ACT

VPN

PS1

HDD1

PS0

HDD0

USB

RESET

SFP1 SFP01

012

7MGMT

AUX CONSOLE

300015

1ASA 5585-X Chassis 2Power Cable (US Shown)

3Blue Console Cable PC Terminal Adapter 4Cable Management Brackets

54 Cable Management Bracket Screws 6Ground Lug Kit

7Slide Rail Kit

Cisco ASA 5585-X Quick Start Guide

3. Network Considerations for Multiple SSPs

2. Connect the power cables to the electrical outlets.

3. Power on the ASA. If you have redundant power supplies, you must power on both modules.

4. Check the Power LED on the front of the ASA; the AC ON indicator should be green, the FAN ON indicator

should be green, and the OUT OK indicator should be off.

3. Network Considerations for Multiple SSPs

The ASA SSP resides in slot 0 (bottom). A second SSP (or network module) can be installed in slot 1 (top). When

you install a non-ASA SSP in slot 1, all non-management interfaces belong to the ASA in slot 0, while the

management interfaces belong to the module. If you install dual ASA SSPs, then they are completely independent

systems.

Default Configuration for Management

See the following table for default configurations for the Management interfaces depending on which module is

installed in slot 1. Note that the left-hand Management interface (when facing the back of the chassis) is not

configured by default.

1Power Supply Module (PS0) 2Power Supply Module (PS1)

249822

Cisco ASA 1200W AC

100-240V

15.0/8.0.A

56/60Hz

FAN

OUT

FAIL

Cisco ASA 1200W AC

100-240V

15.0/8.0.A

56/60Hz

FAN

OUT

FAIL

1 2

PWR

BOOT

ALARM

ACT

VPN

PS1

HDD1

PS0

HDD0

USB RESET

SFP1 SFP0 101234567 MGMT

AUX CONSOLE

PWR

BOOT

ALARM

ACT

VPN

PS1

HDD1

PS0

HDD0

USB RESET

SFP1 SFP0 101234567 MGMT

AUX CONSOLE

ASA Management 0/0

Default IP: 192.168.1.1

Module Management 1/0

Default IP: Varies

Cisco ASA 5585-X Quick Start Guide

4. Connect Interface Cables and Verify Connectivity

All management traffic to and from the non-ASA SSP must enter and exit the Management 1/0 or 1/1 interface.

Because this interface is not an ASA data interface, traffic cannot pass through the ASA over the backplane; you

need to physically cable the management interface to an ASA interface. Non-ASA SSPs usually need Internet

access for updates. See the following typical cabling setup to allow SSP access to the Internet through the ASA

management interface. Other options are possible, depending on how you want to connect your network; for

example, you can make the Management 1/0 interface outside facing; or you can route between it and a different

ASA interface if you have an inside router; and so on.

4. Connect Interface Cables and Verify Connectivity

1. Cable the management and data interfaces. See 3. Network Considerations for Multiple SSPs, page 2 for a

sample cabling scenario.

Slot 0 Module Management

Interface ID

Default IP

address

Slot 1 Module Management

Interface ID

Default IP

address

ASA SSP

The ASA SSP is

the only

supported

module in slot 0.

Management 0/0 192.168.1.1 ASA SSP Management 0/0 192.168.1.1

If you want to put

both ASA SSPs

on the same

network, you

must change

from this default.

All other SSPs Management 1/0 Varies. See the

module quick start

guide for exact

values.

ASA Management 0/0

Module Management 1/0

Set IP to be on same network as M0/0

Management PC

Layer 2

Switch

ASA

management outside

Module

Internet

Module Gateway

to Internet

Cisco ASA 5585-X Quick Start Guide

5. Launch ASDM

2. If you do not use the Management 0/0 for ASA management, you need to configure a data interface for

management. Do one of the following, then recable the computer so it is on the new management network:

—Connect to the console port to configure a data interface for management with CLI. See the Getting Started

chapter in the general operations configuration guide for detailed steps.

—Temporarily connect to Management 0/0, launch ASDM (see 5. Launch ASDM, page 4), and configure a

data interface for management.

3. If you are using the fiber interfaces, you need an SFP+ module for 10-Gigabit Ethernet (a license may be

required) or an SFP module for Gigabit Ethernet. (SFP or SFP+ modules are not included.)

The interfaces available depend on your model. See the hardware guide for more information.

4. Check the LINK/ACT indicators to verify interface connectivity.

5. For software module configuration, see the ASA FirePOWER quick start guide,ASA CX quick start guide, or

IPS quick start guide.

5. Launch ASDM

Using ASDM, you can use wizards to configure basic and advanced features. See the ASDM release notes on

Cisco.com for the requirements to run ASDM.

Procedure

1. On the computer connected to the ASA Management 0/0 interface, launch a web browser.

2. In the Address field, enter the following URL: https://192.168.1.1/admin. The Cisco ASDM web page

appears.

3. Click one of the available options: Install ASDM Launcher, Run ASDM, or Run Startup Wizard.

4. Follow the onscreen instructions to launch ASDM according to the option you chose. The Cisco ASDM-IDM

Launcher appears.

Note: If you choose to click Install ASDM Launcher, in some cases you need to install an identity certificate

for the ASA and a separate certificate for the ASA FirePOWER module according to Install an Identity

Certificate for ASDM.

1(Optional) Slot 1 module, multiple types available. 2Slot 0 ASA SSP

3ASA SSP Management 0/0 interface (RJ-45)

PWR

BOOT

ALARM

ACT

VPN

PS1

HDD1

PS0

HDD0

USB

RESET

SFP1 SFP0 101234567 MGMT

AUX CONSOLE

PWR

BOOT

ALARM

ACT

VPN

PS1

HDD1

PS0

HDD0

USB

RESET

SFP1 SFP0 101234567 MGMT

AUX CONSOLE

Secure Network

Management PC

Unsecure Network

300016

Cisco ASA 5585-X Quick Start Guide

6. Run ASDM Wizards and Advanced Configuration

5. Leave the username and password fields empty, and click OK. The main ASDM window appears.

6. Run ASDM Wizards and Advanced Configuration

ASDM includes many wizards to configure your security policy. See the Wizards menu for all available wizards,

including the Startup Wizard for initial deployment. To continue configuring your ASA, see the documents

available for your software version at Navigating the Cisco ASA Series Documentation.

Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To

view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property

of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other

company. (1110R)

Cisco ASA 5585-X Quick Start Guide

6. Run ASDM Wizards and Advanced Configuration

Inhaltsverzeichnis

Andere Cisco Firewall Handbücher

Cisco

Cisco Small Business RV215W Bedienungsanleitung

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Bedienungsanleitung

Cisco

Cisco Firepower 1010 Bedienungsanleitung

Cisco

Cisco ISA3000-4C-K9 Handbuch

Cisco

Cisco Meraki MX100 Bedienungsanleitung

Cisco

Cisco Firepower 1100 Bedienungsanleitung

Cisco

Cisco C170 Bedienungsanleitung

Cisco

Cisco Meraki MX64W Bedienungsanleitung

Cisco

Cisco MX400 Bedienungsanleitung

Cisco

Cisco ISA 3000 Bedienungsanleitung

Cisco

Cisco Cisco ASA Series Montageanleitung

Cisco

Cisco RV110W Bedienungsanleitung

Cisco

Cisco ASA 5580 Bedienungsanleitung

Cisco

Cisco Meraki MX64 Bedienungsanleitung

Cisco

Cisco ASA 5506-X Bedienungsanleitung

Cisco

Cisco Firepower 4100 Series Installations- und Betriebshandbuch

Cisco

Cisco PIX 520 - PIX Firewall 520 Bedienungsanleitung

Cisco

Cisco ASA 5550 Series Bedienungsanleitung

Cisco

Cisco ASA 5512-X Handbuch

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Handbuch

Cisco

Cisco 3110 Handbuch

Cisco

Cisco LightStream 1010 Bedienungsanleitung

Cisco

Cisco ASA 5506-X Bedienungsanleitung

Cisco

Cisco PIX-515E Bedienungsanleitung

Beliebte Firewall Handbücher anderer Marken

Fortinet

Fortinet FortiGate Voice Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 2300 Bedienungsanleitung

SecureLogix

SecureLogix ETM System Bedienungsanleitung

NETGEAR

NETGEAR ProSafe FVX538 Bedienungsanleitung

Lanner

Lanner FW-8877 Bedienungsanleitung

Huawei

Huawei USG6000 Series Installations- und Betriebshandbuch

H3C

H3C SecPath F5000-AI-15 Bedienungsanleitung

Nexcom

Nexcom DNA 1150 Bedienungsanleitung

Fortinet

Fortinet FortiGate-60 series Bedienungsanleitung

Draytek

Draytek Vigor2860 Series Bedienungsanleitung

Lanner electronics

Lanner electronics FW-7650 Series Bedienungsanleitung

Swisscom

Swisscom Internet Backup Bedienungsanleitung

SonicWALL

SonicWALL NSa 5700 Bedienungsanleitung

DPtech

DPtech FW1000 SERIES Bedienungsanleitung

FEITIAN

FEITIAN MultiPass FIDO Bedienungsanleitung

EBLOCKER

EBLOCKER PRO Bedienungsanleitung

GTA

GTA GB-200 Bedienungsanleitung

Trend Micro

Trend Micro Deep Edge Bedienungsanleitung