Cisco ATA 186 Bedienerhandbuch
CHAPTER
2-1
Cisco ATA 186 Installation and Configuration Guide
OL-1267-01
2
Installing the Cisco ATA 186
This chapter provides information about installing the Cisco ATA 186.
English is the default language. For information on the upgrade process, see
Chapter 6, “Upgrading the Cisco ATA 186 Software.”
Installation Overview
The general steps necessary to install the Cisco ATA 186 are:
1. Plan the network and Cisco ATA 186 configuration.
2. Install the Ethernet connection.
3. Install and configure the other network devices; for example, gatekeeper if
you are using H.323 or proxy server if you are using SIP.
4. If you will be routing calls through the Public Switched Telephone Network
(PSTN), install and configure the Gateway.
5. Install the Cisco ATA 186.
6. Configure the Cisco ATA 186.
7. Perform any troubleshooting and maintenance, including upgrading the
software if necessary.
Chapter 2 Installing the Cisco ATA 186
Installation Overview
2-2
Cisco ATA 186 Installation and Configuration Guide OL-1267-01
Figure 2-1 shows an example of a network with a Cisco ATA 186.
Figure 2-1 Example Network Diagram
62467
10BaseT ACT 5VPHONE1 PHONE2
ATA 186 Broadband
modem Voice
Gateway
Gatekeeper
or Proxy Server
PSTN
IP
Network
ISP
Connection
POP
2-3
Cisco ATA 186 Installation and Configuration Guide
OL-1267-01
Chapter 2 Installing the Cisco ATA 186 Network Requirements
Network Requirements
The Cisco ATA 186 acts as a terminal on an IP network. You need the following
equipment:
•One or two standard analog telephone handsets.
•Ethernet connection.
•Gatekeeper or proxy server—Currently, there must be a device running ITU
H.323 or RFC 2543bis SIP-complaint software. The gatekeeper must be
running the applicable version of software for the features and protocol you
want to use.
•Voice Packet Gateway—Required if you are connecting to the Public
Switched Telephone Network (PSTN).
•Fax machine (optional).
•If you are using a firewall, Cisco recommends that it be a Cisco PIX firewall,
Version 5 or later versions.
Safety Recommendations
To ensure general safety, follow these guidelines:
•Do not open or disassemble this product.
•Do not get this product wet or pour liquids into this device.
•Do not perform any action that creates a potential hazard to people or makes
the equipment unsafe.
Chapter 2 Installing the Cisco ATA 186
System Requirements
2-4
Cisco ATA 186 Installation and Configuration Guide OL-1267-01
System Requirements
Caution The Cisco ATA 186 is intended for use with a 5V DC power adaptor only.
The Cisco ATA 186 installation package includes:
•Cisco ATA 186
•Cisco ATA 186 documentation
•5V Power Adaptor
You also need:
•10BaseT category-3 cable or better
•One or two analog touch-tone telephones
Note Telephones must be set to use tone, rather than pulse dialing for the
Cisco ATA 186 to operate correctly.
2-5
Cisco ATA 186 Installation and Configuration Guide
OL-1267-01
Chapter 2 Installing the Cisco ATA 186 Installation Warnings
Installation Warnings
This section contains important safety information.
Number 26 AWG Warning
Warning
To reduce the risk of fire, use only No. 26 AWG or larger
telecommunication line cord.
Waarschuwing
Om brandgevaar te reduceren, dient slechts
telecommunicatielijnsnoer nr. 26 AWG of groter gebruikt te worden.
Varoitus
Tulipalovaaran vähentämiseksi käytä ainoastaan nro 26 AWG- tai
paksumpaa tietoliikennejohdinta.
Attention
Pour réduire le risque d’incendie, n’utiliser que des cordons de
lignes de télécommunications de type AWG nº 26 ou plus larges.
Warnung
Zur Reduzierung der Feuergefahr eine Fernmeldeleitungsschnur der
Größe 26 AWG oder größer verwenden.
Avvertenza
Per ridurre il rischio di incendio, usare solo un cavo per linea di
telecomunicazioni di sezione 0,12 mm
2
(26 AWG) o maggiore.
Advarsel
Bruk kun AWG nr. 26 eller telekommunikasjonsledninger med større
dimensjon for å redusere faren for brann.
Aviso
Para reduzir o risco de incêndio, utilize apenas terminais de fio de
telecomunicações Nº. 26 AWG ou superiores.
¡Advertencia!
Para reducir el riesgo de incendios, usar sólo líneas de
telecomunicaciones de calibre No. 26 AWG o más gruesas.
Varning!
För att minska brandrisken skall endast Nr. 26 AWG eller större
telekommunikationsledning användas.
Chapter 2 Installing the Cisco ATA 186
Installation Warnings
2-6
Cisco ATA 186 Installation and Configuration Guide OL-1267-01
Short-Circuit Protection Warning
Warning
This product relies on the building's installation for short-circuit
(overcurrent) protection. Ensure that a fuse or circuit breaker no
larger than 120VAC, 20A U.S. (240VAC, 16 to 20A international) is
used on the phase conductors (all current-carrying conductors).
The fuse or circuit breaker must have adequate safety approvals
recognized by the country of usage.
Waarschuwing
Dit product is afhankelijk van de installatie van het gebouw voor
bescherming tegen kortsluiting (overstroom). Zorg ervoor dat de
zekering of stroomonderbreker die gebruikt wordt niet groter is
dan 120 V~, 20 ampère in de V.S. of 240 V~, 16-20 ampère
internationaal op de fasegeleiders (alle stroomdragende
geleiders). De zekering of stroomonderbreker dient de juiste
veiligheidsgoedkeuringen te hebben in het land waarin het
gebruikt wordt.
Varoitus
Tämä tuote on riippuvainen rakennuksen oikosulkusuojauksesta
(ylivirtasuojauksesta). Varmista, että vaihejohtimissa (kaikissa
jännitteellisissä johtimissa) käytetään alle 240 V vaihtovirran,
16–20 ampeerin (kansainvälinen) tai 120 V vaihtovirran, 20
ampeerin(Yhdysvallat)sulakettataivirtakytkintä.Sulakkeessatai
virtakytkimessä on oltava käyttömaassa tunnistetut, riittävät
turvahyväksynnät.
Attention
Pour la protection contre les courts-circuits (surtension), ce
produit utilise les dispositifs intégrés au bâtiment. Assurez-vous
qu'un fusible ou un disjoncteur est utilisé sur les conducteurs de
phase (tous les conducteurs porteurs de courant). Le fusible ou le
disjoncteur (maximum 240 V CA, 16 à 20 A [aux USA, maximum 120
V CA, 20 A]) doit être conforme aux normes de sécurité en vigueur
dans votre pays.
2-7
Cisco ATA 186 Installation and Configuration Guide
OL-1267-01
Chapter 2 Installing the Cisco ATA 186 Installation Warnings
Warnung
Diese Produkt erfordert eine Gebäudeabsicherung gegen
Kurzschluß (Überstrom). Achten Sie darauf, daß auf den
Phasenleitern (allen stromführenden Leitern) eine Sicherung oder
ein Schaltkreisunterbrecher verwendet wird, der nicht größer ist
als 120VAC, 20A U.S. (240VAC, 16 bis 20A international). Die
Sicherung oder der Schaltkreisunterbrecher muß angemessenen
Sicherheitsvorschriften genügen, die den Bestimmungen des
Anwendungslandes entsprechen.
Avvertenza
La protezione di questo prodotto da cortocircuiti (sovracorrente)
dipende dall'impianto elettrico dell’edificio. Assicuratevi che un
fusibile o interruttore di circuito con meno di 120VAC, 20A U.S.
(240VAC,da16a20Ainternazionale) venga utilizzatosuiconduttori
di fase (tutti i conduttori di corrente elettrica). Il fusibile o
interruttoredicircuitodeverispondereallespecifichedisicurezza
invigore nel paese dove viene utilizzato.
Advarsel
Dette produktet er avhengig av bygningens installasjoner for
overstrømsbeskyttelse(kortslutning). Kontrollerat det ikkebrukes
en sikring eller overbelastningsbryter som er større enn 120 V, 20
ampere i USA, eller 240 V, 16 til 20 ampere internasjonalt, på
faselederne (alle strømførende ledere). Sikringen eller
overbelastningsbryteren må være sikkerhetsgodkjent i det
aktuelle landet der den skal brukes.
Aviso
Este dispositivo depende das instalações existentes para
protecção contra curto-circuitos (sobrecarga). Assegure-se de
que utiliza um fusível ou um disjuntor com uma capacidade não
superior a 120VAC, 20A U.S. (240VAC, 16 a 20A internacional) nos
condutores de fase (todos os condutores de corrente). O fusível ou
disjuntor deverá possuir as necessárias aprovações de segurança
por parte das autoridades locais.
Chapter 2 Installing the Cisco ATA 186
Installation Warnings
2-8
Cisco ATA 186 Installation and Configuration Guide OL-1267-01
TN Power Systems Warning
¡Advertencia!
Este producto ha sido diseñado teniendo en cuenta que la
instalación del edificio contará con protección contra
cortocircuitos (sobrevoltajes). Asegúrese de que se usa un fusible
o cortacircuitos no superior a 120VAC, 20A en los EE.UU. (240VAC,
de16a 20Aen el restode países)en los conductores de fase(todos
los conductores de transporte corriente). El fusible o
cortacircuitos debe contar con las aprobaciones de seguridad
adecuadas y reconocidas por el país en el que vayan a usarse.
Varning!
Denna produkt förlitar sig på att byggnadens installation är
försedd med skydd mot kortslutning (överström). Se till att en
säkring eller ett överspänningsskydd för högst 120 V~, 20 A USA
(240 V~, 16 – 20 A internationellt) används på fasledarna (alla
strömförande ledare). Säkringen eller överspänningsskyddet
måste ha fullgoda säkerhetstillstånd som erkänns av
användningslandet.
Warning
The device is designed to work with TN power systems.
Waarschuwing
Het apparaat is ontworpen om te functioneren met TN
energiesystemen.
Varoitus
Koje on suunniteltu toimimaan TN-sähkövoimajärjestelmien
yhteydessä.
Attention
Ce dispositif a été conçu pour fonctionner avec des systèmes
d'alimentation TN.
Warnung
Das Gerät ist für die Verwendung mit TN-Stromsystemen ausgelegt.
Avvertenza
Il dispositivo è stato progettato per l’uso con sistemi di
alimentazione TN.
2-9
Cisco ATA 186 Installation and Configuration Guide
OL-1267-01
Chapter 2 Installing the Cisco ATA 186 Installation Warnings
Installing the Cisco ATA 186
Follow these steps to install the Cisco ATA 186 hardware. (See Figure 2-2.)
Figure 2-2 Installing the Cisco ATA 186
Advarsel
Utstyret er utfomet til bruk med TN-strømsystemer.
Aviso
O dispositivo foi criado para operar com sistemas de corrente TN.
¡Advertencia!
El equipo está diseñado para trabajar con sistemas de alimentación
tipo TN.
Varning!
Enheten är konstruerad för användning tillsammans med
elkraftssystem av TN-typ.
10BaseT ACT 5VPHONE 1 PHONE 2
62290
ABC D
Chapter 2 Installing the Cisco ATA 186
Installation Warnings
2-10
Cisco ATA 186 Installation and Configuration Guide OL-1267-01
A—Phone 1 connector (RJ-11)
B—Phone 2 connector (RJ-11)
C—10Base-T Ethernet connector
D—12V power connector
Step 1 Place the Cisco ATA 186 near an electrical outlet. Connect the first telephone to
the PHONE 1 input port (A) on the rear panel of the Cisco ATA 186 by using a
telephone line cord with an RJ-11 connector. The PHONE 1 input port will be the
primary telephone line.
Caution Do not connect the Cisco ATA 186 PHONE input ports to the telephone wall
jack. To prevent damage to the device or building telephone wiring, connect
each Cisco ATA 186 PHONE port to a telephone only, never to a telephone
wall jack.
Step 2 You can connect a second telephone to the PHONE 2 input (B) by using a second
telephone line cord. The PHONE 2 input is the secondary telephone line.
Note If you are connecting only one telephone to the Cisco ATA 186, you must use
the PHONE 1 input; otherwise, the telephone cannot place calls.
Step 3 Connect one end of a 10-BaseT Ethernet cable (C) to a hub, switch, or broadband
modem (DSL, cable, and so on).
Step 4 Connect the other end of the Ethernet cable to the RJ-45 input port (C) on the rear
panel of the Cisco ATA 186.
Note Use a crossover Ethernet cable to connect the Cisco ATA 186 to another
Ethernet device (such as a router or PC) without using a hub. Otherwise, use a
straight through Ethernet cable.
Step 5 Plug the AC power adaptor into an electrical outlet. Insert the power cord into the
rear panel of the unit (D). Each connected telephone should ring once, indicating
that the Cisco ATA 186 is powered and ready to use. When the Cisco ATA 186 is
properly connected and powered up, the green activity LED flashes. The activity
LED, labeled ACT, indicates network activity.
Andere Handbücher für ATA 186
8
Inhaltsverzeichnis
Andere Cisco Tor Handbücher
Cisco
Cisco Linksys WAG310G Bedienungsanleitung
Cisco
Cisco IOS XE Intelligent Services Bedienungsanleitung
Cisco
Cisco DPC3928 DOCSIS Bedienungsanleitung
Cisco
Cisco WAG54G Bedienungsanleitung
Cisco
Cisco SPA232D Bedienungsanleitung
Cisco
Cisco Physical Access CIAC-GW-K9 Bedienungsanleitung
Cisco
Cisco VG200 Bedienungsanleitung
Cisco
Cisco Linksys WAG200G Bedienungsanleitung
Cisco
Cisco ASR 5000 Bedienungsanleitung
Cisco
Cisco VG410 Handbuch
Cisco
Cisco Small Business SPA8800 Bedienungsanleitung
Cisco
Cisco TelePresence Advanced Media Gateway 3610 Bedienungsanleitung
Cisco
Cisco SPA-841 - Sipura VoIP Phone Bedienungsanleitung
Cisco
Cisco DPC2425 Bedienungsanleitung
Cisco
Cisco DPC2425 Bedienungsanleitung
Cisco
Cisco DPC2420 Bedienungsanleitung
Cisco
Cisco Linksys WAG325N Bedienungsanleitung
Cisco
Cisco EPC2425 Bedienungsanleitung
Cisco
Cisco Meraki Z3C Bedienungsanleitung
Cisco
Cisco SPA122 ATA Bedienungsanleitung
Beliebte Tor Handbücher anderer Marken
LST
LST M500RFE-AS Bedienungsanleitung
Kinnex
Kinnex Media Gateway Bedienungsanleitung
2N Telekomunikace
2N Telekomunikace 2N StarGate Bedienungsanleitung
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung
Telsey
Telsey CPVA 500 - SIP Bedienungsanleitung
