Cisco LINKSYS AG241 Bedienungsanleitung
Model No.
Quick Installation Guide
A Division of Cisco Systems, Inc.
®
WIRED
AG241 (EU/LA/UK)
with 4-Port Switch
ADSL2 Gateway
Package Contents
•ADSL2Gateway
•UserGuideonCD-ROM
• Ethernet Network Cable
• Phone Cable
• Power Adapter
• Microfilterorsplitter(notsuppliedwith
all models)
• Quick Installation
2
Connect the ADSL2 Gateway
1
In Step 1, you will connect the Gateway
to your ADSL line and to the computers
in your home or business.
First, make sure that all the devices that
you’ll be working with are powered
down, including your PCs and the
Gateway.
AConnect one end of the provided
phone cable to the wall jack with
ADSL service.
NOTE: To avoid interference, you
may need to place a
microfilter or splitter
between the phone
cable and wall jack.
Contact your service
provider for more
information.
BConnect the other end of the
phone cable to the LINE port that
is on the back of the Gateway.
CConnect one end of the provided
Ethernet cable to your PC’s
Ethernet adapter. Connect the
other end of the cable to one of
the Ethernet ports on the back of
the Gateway. Repeat this process
for every PC that you want to
connect to the Gateway.
If you are connecting more than
four PCs to the Gateway, you will
also need to connect a hub or
switch to the Gateway.
NOTE: If your PC’s Ethernet
adapter is not set up, refer
to the Ethernet adapter’s
user guide for more
information.
B
C1
C2
3
DConnect the power adapter to
the Gateway. Connect the power
adapter to the electrical outlet.
ETurn on the Gateway. Then, turn
on the first PC that you want to use
to configure the Gateway.
Proceed to Step 2: Configure the
ADSL2 Gateway.
D
IMPORTANT: Makesureyouonlyplacethe
microfilter or splitter between the phone
and the wall jack and not between the
Gateway and the wall jack. Otherwise your
ADSL will not connect.
4
2
In Step 2, you will configure the Gateway
to be able to gain access to the Internet
through your Internet Service Provider (ISP).
You will need the setup information
provided by your ADSL ISP. If you do not
have this information, please contact
them before proceeding.
The instructions from your ISP tell you how
to set up your PC for Internet access.
Because you are now using the Gateway
to share Internet access among several
computers, you will use the setup
information to configure the Gateway
instead of your PC.
NOTE: You only need to
configure the Gateway
once using the first
computer you set up.
AOpen your web browser. (You may
get an error message at this point.
Continue following these directions.)
Enter http://192.168.1.1 in the web
browser’s Address field. Press the
Enter key.
BAn Enter Network Password window
will appear (Windows XP users will
see a Connect to 192.168.1.1
window). Enter admin in lowercase
letters in the User Name field, and
enter admin in lowercase letters in
the Password field (admin is the
default user name and password.)
Then, click the OK button.
Configure the ADSL2 Gateway
B
5
Model No.
C
Dynamic IP Address
CThe Basic Setup screen will
appear with the Setup tab
selected. Based on the setup
instructions from your ISP, you may
need to provide the following
information.
ADSL Settings. The Gateway
supports five Encapsulations: RFC
1483 Bridged, RFC 1483 Routed,
RFC 2516 PPPoE, RFC 2364
PPPoA, IPoA, and Bridged Mode
Only. Each Basic Setup screen
and available features will differ
depending on what type of
encapsulation you select.
VC Settings. Virtual Circuits (VPI
and VCI): These fields consist of
two items: VPI (Virtual Path
Identifier) and VCI (Virtual Channel
Identifier). Your ISP will provide the
correct settings for these fields.
Multiplexing: Select LLC or VC,
depending on your ISP.
Your ISP will provide the correct
settings.
1 RFC 1483 Bridged
Dynamic IP Address
If your ISP says that you are
connecting through a dynamic IP
address, perform these steps:
aSelect RFC 1483 Routed for the
Encapsulation.
bSelect Obtain an IP Address
Automatically for the IP Setting.
6
Static IP Address
cClick the Save Settings button to
save the settings.
Static IP Address
If your ISP says that you are
connecting through a static or fixed
IP address, perform these steps:
aSelect RFC 1483 Bridged for the
Encapsulation.
bSelect Use the following IP
Address as the IP Setting.
cEnter the IP Address and the
Subnet Mask.
dEnter the Default Gateway
address.
eEnter the DNS in the Primary and/
or Secondary fields. You need to
enter at least one DNS address.
fClick the Save Settings button to
save the settings.
2 RFC 1483 Routed
If your ISP says that you are
connecting through RFC 1483
Routed using a static IP address,
perform these steps:
aSelect RFC 1483 Routed for the
Encapsulation.
bEnter the IP Address and the
Subnet Mask. RFC 1483 Routed
7
PPPoE
cEnter the Default Gateway
address.
dEnter the DNS in the Primary and/
or Secondary fields. You need to
enter at least one DNS address.
eClick the Save Settings button to
save the settings.
3 RFC 2516 PPPoE or RFC 2364
PPPoA
If your ISP says that you are
connecting through PPPoE or PPPoA,
or if you normally enter a user name
and password to access the
Internet, perform these steps:
aSelect RFC2516 PPPoE or RFC
2364 PPPoA as appropriate for the
Encapsulation.
bIf you selected PPPoE, enter the
Service Name (if required).
cEnter the User Name (if required).
dEnter the Password.
eSelect Keep Alive if you always
want to be connected to your ISP,
or select Connect on Demand if
you are charged for the time that
you are connected to your ISP.
fClick the Save Settings button to
save the settings.
PPPoA
NOTE:PPPoE users, who require a
second PPPoE by their ISP, can
select Enable for Second PPPoE
and enter the appropriate
information for the second account.
8
4IPoA
If your ISP says that you are
connecting through IPoA, perform
these steps:
aSelect IPoA for the Encapsulation.
bEnter the IP Address and the
Subnet Mask.
cEnter the Default Gateway
address.
dEnter the DNS in the Primary
and/or Secondary fields. You
need to enter at least one DNS
address.
eClick the Save Settings button to
save the settings.
DIf you haven’t already done so,
click the Save Settings button to
save your Setup settings. Close
the web browser.
ECongratulations! You’ve
successfully configured the
Gateway. Test the setup by
opening your web browser from
any computer and entering:
www.linksys.com/registration
FIf you are unable to reach our
website, you may want to review
the installation and configuration
sections in this Quick Installation or
refer to the Troubleshooting
section of the User Guide.
AG241-EU_LA_UK-QIG-41213NC JL
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2004
Cisco Systems, Inc. All rights reserved.
Foradditionalinformationortroubleshooting
help, refer to the User Guide on the CD-ROM
or the Technical Support Insert. You can also
e-mail for further support.
Website
http://www.linksys.com/international
Registrations
http://www.linksys.com/registration
IPoA
WIRED
A Division of Cisco Systems, Inc.
®
Modelnr.
Installationsvejledning
1
Modelnr.
AG241 (DK)
med 4-Port Switch
Pakkens indhold
• ADSL2-gatewayen
• Brugervejledning på cd-rom (kun på
engelsk)
• Ethernet-kabel
• Telefonledning
• Strømforsyning
• Mikrofilter eller fordeler (følger ikke
med alle modeller)
• Installationsvejledning
ADSL2-gatewayen
2
1
I trin 1 tilslutter du gatewayen til
ADSL-linjen og til computerne i dit
hjem/din virksomhed.
Kontroller først, at alle de involverede
enheder er slukket, herunder dine
pc'er og gatewayen.
ATilslut den ene ende af den
medfølgende telefonledning til
ADSL-vægstikket.
BEMÆRK: Det kan være
nødvendigt at placere
et mikrofilter eller en
fordeler mellem
telefonledningen og
vægstikket for at undgå
interferens. Kontakt din
tjenesteudbyder for at
få yderligere
oplysninger.
BTilslut den anden ende af
telefonledningen til LINE-porten
bag på gatewayen. (Figur B)
CTilslut den ene ende af det
medfølgende Ethernet-kabel til
pc'ens Ethernet-adapter
(Figur C1). Tilslut den anden
ende af kablet til en af Ethernet-
portene bag på gatewayen
(Figur C2). Gentag denne
fremgangsmåde for alle de
pc'er, du vil tilslutte til gatewayen.
Tilslutning af ADSL2-gatewayen
B
C1
C2
Andere Handbücher für LINKSYS AG241
1
Inhaltsverzeichnis
Sprachen:
Andere Cisco Tor Handbücher
Cisco
Cisco DPA 7610 Bedienungsanleitung
Cisco
Cisco Firepower Management Center 1000 Bedienungsanleitung
Cisco
Cisco Linksys WPG12 Bedienungsanleitung
Cisco
Cisco Linksys WAG310G Bedienungsanleitung
Cisco
Cisco VG410 Handbuch
Cisco
Cisco D-PCG1000 PowerKEY CAS Bedienungsanleitung
Cisco
Cisco Meraki Z1 Bedienungsanleitung
Cisco
Cisco DPC2434 Bedienungsanleitung
Cisco
Cisco RF Gateway 10 Bedienungsanleitung
Cisco
Cisco EPC3928 DOCSIS Bedienungsanleitung
Cisco
Cisco VG420 Bedienungsanleitung
Cisco
Cisco SIEMENS HICOM 330E Montage- und Bedienungsanleitung
Cisco
Cisco TelePresence ISDN GW MSE 8321 Bedienungsanleitung
Cisco
Cisco DPC2434 Bedienungsanleitung
Cisco
Cisco DPC3825 Bedienungsanleitung
Cisco
Cisco Explorer 4250 Bedienungsanleitung
Cisco
Cisco LINKSYS RFC 2364 Bedienungsanleitung
Cisco
Cisco ASR 5000 Bedienungsanleitung
Cisco
Cisco DPC3827 Bedienungsanleitung
Cisco
Cisco DPC3929CM Bedienungsanleitung
Beliebte Tor Handbücher anderer Marken
LST
LST M500RFE-AS Bedienungsanleitung
Kinnex
Kinnex Media Gateway Bedienungsanleitung
2N Telekomunikace
2N Telekomunikace 2N StarGate Bedienungsanleitung
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Bedienungsanleitung
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Bedienungsanleitung
Telsey
Telsey CPVA 500 - SIP Bedienungsanleitung
