Cisco MX450 Bedienungsanleitung

MX450 Installation Guide

This document describes how to install and set up the MX450 security appliance. Additional reference documents are available online at: www.meraki.com/

library/products.

MX450 Overview

The Meraki MX450 is an enterprise security appliance designed for distributed networks that require remote administration. It is ideal for network administrators

who demand both ease of deployment and a state-of-the-art feature set. The MX450 appliance provides the following new features:

• Two dedicated uplink SFP+10GbE ports

• Support for eight configurable GbE(RJ45), eight GbE SFP and eight 10GbE SFP+ connections

• USB port, to support approved 3G/4G cards for failover to cellular networks

• 128GB (SSD) cache storage

• Dedicated management port

• Front-panel rack mounts

Package Contents

In addition to the MX450, the following are provided:

MX450 Front Panel

Ports and Status Indicators

The MX450 uses LEDs to inform the user of the device's status. When the device powers on, all the Internet LEDs flash twice. Additional functions are described

below, from left to right.

Item Function LED Status Meaning

1 Power Solid orange Power is applied

Rainbow colors Unit is attempting to contact the

Cloud

Flashing white Operation is in progress

Solid white Fully operational

2 USB connectivity Off During boot or USB link

Solid orange Initial link

Flashing orange Internet connectivity not complete

Green USB connection detected

3 HA status Off No HA available

Orange Initial link

Flashing orange High availability not complete

Green HA available

Reset button

Insert a paper clip if a reset is required.

A brief, momentary press: To delete a downloaded configuration and reboot.

Press and hold for more than 10 seconds: To force the unit into a full factory reset.

MX450 Back Panel

Please note that the serial number is located on the product label at the back panel of the MX450-HW.

Mounting Hardware

The mounting hardware includes four sets of standard slot-head rack screws and nuts. The additional screws and nuts are different screw standards meant to

accommodate the most common rack mounts. When installing the appliance, make sure that there is sufficient space between the rear of the rack and other

obstacles to ensure adequate airflow. Ventilation is from side to side not from front to back. This MX security appliance requires a minimum of 10mm clearance

between the venting holes and any obstruction.

Safety Guidelines

Warning: The system must be disconnected from all sources of power and the power cord removed from the power supply module(s)

before accessing, installing, or removing system components.

Caution: The Optical Transceiver product should use UL listed, and Rated Laser Class I, 3.3Vdc.

Connecting to WAN

All Meraki MX devices must have an IP address. This section describes how to configure your local area network before you deploy it. A local management web

service, running on the appliance, is accessed through a browser running on a client PC. This web service is used for configuring and monitoring basic ISP/WAN

connectivity.

Setting up a Static IP Address

Do the following to configure basic connectivity and other networking parameters:

1. Using a client machine such as a laptop, connect to the management port of the MX.

2. Using a browser on the client machine, access the appliance's built-in web service by browsing

to http://setup.meraki.com. (You do not have to be connected to the Internet to reach this address)

3. Click Uplink configuration under the Local status tab. The default credentials use the device serial number as

the username, with a blank password field.

4. Choose Static for the IP Assignment option.

5. Enter the IP address, subnet mask, default gateway IP and DNS server information.

To ensure that the client PC is redirected to the local web service in the following step, you must disable all other network services (ex: wi-fi) on your

client machine.

Setting up a DHCP IP Address

By default all MX devices are configured to DHCP from upstream WAN / ISP servers. Simply plug the MX's WAN / Internet port to your upstream circuit and wait

a few minutes for the unit to negotiate a DHCP address.

Additional Settings

Setting VLANs

If your WAN uplink is on a trunk port, choose VLAN tagging > Use VLAN tagging and enter the appropriate value for VLAN ID for your network.

Setting PPPoE

PPPoE authentication may be required if you are connecting MX device to a DSL circuit. You need to know your authentication option and credentials (supplied

by your ISP) in order to complete these steps.

• Choose Connection Type > PPPoE.

• Select your Authentication option.

• If you select Use authentication, enter appropriate values for Username and Password.

Web Proxy Pettings

These settings take effect if the MX device has to fall back to using HTTP to contact the Cloud Controller. By default, web proxy is disabled. To enable web

proxy, do the following:

• Choose Web proxy > Yes.

• Enter values as appropriate for Hostname or IP and Port.

• If you require authentication, choose Authentication > Use authentication, and enter appropriate values

for Username and Password.

Configuring Physical link settings

To configure physical link settings on the Ethernet ports, click Local status > Ethernet configuration. You can enable half duplex, full duplex,

and autonegotiation, as well as set 10 or 100-Mbps data rates.

When the WAN connection is fully enabled, Internet LED will turn green.

Please note that all these settings below are accessible only via the local management console.

To apply all configuration settings to the appliance, be sure to click Save Settings at the bottom of the page.

Andere Cisco Modem Handbücher

Cisco

Cisco DPC2100 Bedienungsanleitung

Cisco

Cisco WebSTAR DPX100 Bedienungsanleitung

Cisco

Cisco DPC3925 Bedienungsanleitung

Cisco

Cisco DPC3216 Bedienungsanleitung

Cisco

Cisco DPQ2160 Bedienungsanleitung

Cisco

Cisco WAP300N Bedienungsanleitung

Cisco

Cisco uBR904 Montageanleitung

Cisco

Cisco uBR904 Bedienungsanleitung

Cisco

Cisco DPC3000 Bedienungsanleitung

Cisco

Cisco 605 Bedienungsanleitung

Cisco

Cisco LINKSYS ADSL2MUE Bedienungsanleitung

Cisco

Cisco EPC3925 Bedienungsanleitung

Cisco

Cisco Linksys DPC3008 Bedienungsanleitung

Cisco

Cisco DPC2203C2 Bedienungsanleitung

Cisco

Cisco DPC2203C Betriebsanleitung

Cisco

Cisco DPC3848 Bedienungsanleitung

Cisco

Cisco EPC3208G EuroDOCSIS 3.0 8x4 Bedienungsanleitung

Cisco

Cisco 3848 Bedienungsanleitung

Cisco

Cisco Linksys E800 Bedienungsanleitung

Cisco

Cisco WCM300 - Channel Bonded Cable Modem Bedienungsanleitung

Cisco

Cisco uBR904 Bedienungsanleitung

Cisco

Cisco EPC2203 Bedienungsanleitung

Cisco

Cisco DPC3212 Bedienungsanleitung

Cisco

Cisco DPC2202 Bedienungsanleitung

Beliebte Modem Handbücher anderer Marken

Davicom

Davicom DM562AP Bedienungsanleitung

Zte

Zte WiMAX Bedienungsanleitung

Intelimax

Intelimax MA-2060 Bedienungsanleitung

SMC Networks

SMC Networks D3CM1604V Gebrauchs- und Pflegehandbuch

Telstra

Telstra Wi-Fi 4G Advanced Pro X Bedienungsanleitung

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Bedienungsanleitung

Samsung

Samsung AceLink SAM-335A Bedienungsanleitung

Enfora

Enfora Enabler-G Kurzanleitung zur Einrichtung

iRZ

iRZ ATM2-232 Bedienungsanleitung

Zhone

Zhone 6310 Bedienungsanleitung

Paradyne

Paradyne Hotwire 7976 Bedienungsanleitung

US Robotics

US Robotics 3453C Bedienungsanleitung

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Bedienungsanleitung

Zte

Zte MF823 Bedienungsanleitung

Four-Faith

Four-Faith F1403 Bedienungsanleitung

Sierra Wireless

Sierra Wireless AIRLINK MP595W Bedienungsanleitung

Gemtek

Gemtek WiMAX WIXFBR-103 Bedienungsanleitung

Zoom

Zoom 1070 Series Bedienungsanleitung