Cisco 1100 Series Bedienungsanleitung

Installing and Upgrading Internal Modules and

FRUs

•Installing and Upgrading Internal Modules and FRUs, page 1

Installing and Upgrading Internal Modules and FRUs

This document describes how to install and upgrade internal modules and field replaceable units (FRUs) in

the Cisco 1100 Series Integrated Services Routers (ISRs). The install and upgrade information is contained

in these sections:

Safety Warnings

Class 1 laser product. Statement 1008Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.

Statement 1030

Warning

Accessing Internal Modules

To access the internal modules on the router, you must first disconnect from the power source and then remove

the chassis cover. See the Replacing the Cover section for instructions on how to remove and later replace

the chassis cover on the routers.

Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network

voltages. Statement 1041

Warning

Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router

Replacing the Chassis Cover

The Cisco 1100 Series ISRs have a removable cover.

Do not run the router with the cover off. Doing so can cause the router to overheat very quickly.

Use a number-2 Phillips screwdriver to perform the following tasks.

Removing the Cover

To remove the cover, perform the following steps.

Step 1 Read the Safety Warnings and disconnect the power supply before you perform any module replacement.

Step 2 Confirm the router is turned off and disconnected from the power supply or power supplies. If a redundant power is

used, disconnect from the redundant power supply.

Step 3 Place the chassis on a flat surface.

Step 4 Remove all the screws on the both sides of the router; seven on each side.

Step 5 Pull the cover to disengage the slots along the front (bezel) edge of the chassis, as shown in the figure below.

Figure 1: Removing the Cover

Slots1

Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router

Installing and Upgrading Internal Modules and FRUs

Accessing Internal Modules

Screw holes (7 numbers on each side)2

Replacing the Cover

To replace the cover, perform the following steps.

Step 1 Read the Safety Warnings, on page 1 and disconnect the power supply before you begin.

Step 2 Confirm the router is turned off and disconnected from the power supply or power supplies. If a redundant power is used

disconnect from the redundant power supply.

Step 3 Place the chassis on a flat surface.

Step 4 Locate the cover hooks on the mating slots and slide the cover towards the bezel side.

Step 5 Install seven screws on each side.

Locating Internal and External Slots for Modules

This section describes the locations of internal modules on the router motherboard. Internal modules include

PoE daughter card on the Cisco1100 Series ISRs.

Figure 2: Module Location in the Cisco 1100 Series ISR

Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router

Installing and Upgrading Internal Modules and FRUs

Locating Internal and External Slots for Modules

PoE Module1

Installing the Internal PoE Daughter Card

Use the following procedure to install an Internal PoE daughter card:

Step 1 Read the Safety Warnings and disconnect the power supply before you perform any module installation.

Step 2 Confirm the router is turned off and disconnected from the power supply.

Step 3 Open the chassis according to the instructions in the Removing the Chassis section.

Step 4 Locate the three metal standoff holes, and install the metal standoffs into the three holes. Make sure that the standoffs

are straight when installed. Tighten them gently but firmly, to a torque of 6-8 in-lbf.

Step 5 Place the PoE daughter card on top of the three metal standoffs, lining up the screw holes in the PoE daughter card with

the metal standoffs.

Step 6 Gently push the PoE daughter card down towards the system board until it is firmly fixed.

Step 7 Insert the three M3 (48-0530-01) screws provided, through the PoE daughter card and into the metal standoffs. Tighten

the screws using a torque of 5 in-lb.

Step 8 Close the chassis cover according to the instructions in the Replacing the Cover section, and connect the power supply

cable.

Figure 3: Internal PoE Daughter Card Assembly

PoE Daughter Card2Screws1

Metal Standoffs3

Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router

Installing and Upgrading Internal Modules and FRUs

Locating Internal and External Slots for Modules

Removing and Replacing the Internal PoE Daughter Card

Use the following procedure to remove and replace the Internal PoE daughter card:

Step 1 Read the Safety Warnings and disconnect the power supply before you remove or replace the module.

Step 2 Open the chassis, locate the PoE daughter card assembly.

Step 3 Remove the three M3 (48-0530-01) screws.

Step 4 Pull the PoE daughter card out of the connector. If replacing the card, insert the new PoE daughter card and tighten the

screws to a torque of 5 in-lb.

Step 5 Place the removed card in an anti-static bag to protect it from ESD damage.

To upgrade the PoE daughter card, follow the steps mentioned in the Installing the Internal PoE Daughter Card

section.

Note

Removing and Replacing the USB Flash Token Memory Stick

The Cisco 1100 Series ISRs contain port for a 1 GB flash token memory stick to store configurations or Cisco

IOS XE consolidated packages.

Only Cisco USB Flash memory modules are supported by Cisco routers.Note

Do not remove a USB Flash memory module when issuing some file access command or a read/write

operation to the Flash memory module when it is processing. The router might reload or the USB Flash

memory module can be damaged. You can check to see if the USB activity LED on the router front panel

is flashing, prior to the removal of the USB device

Caution

To remove and then replace a USB flash token memory stick from the router, follow these steps:

Step 1 Pull the memory stick from the USB port.

Step 2 To replace a Cisco USB Flash memory stick, simply insert the module into the USB port. The Flash memory module

can be inserted in only one way, and can be inserted or removed regardless of whether the router is powered up or not.

What to Do Next

This completes the USB Flash memory installation procedure.

Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router

Installing and Upgrading Internal Modules and FRUs

Removing and Replacing the USB Flash Token Memory Stick

AC Power Supplies

Overview of the AC Power Supply

Power supply of the Cisco 1100 Series ISRs is an external AC to DC power adapter. The external power

adapter DC power connector plugs in to the router 4-pin power connector, to power the unit.

Figure 4: Power Supply Unit

Power Cable1

Installing and Removing SFP Modules

This section describes how to install optional small-form-factor pluggable (SFP) modules in the router to

provide optical Gigabit Ethernet connectivity.

The SFP module installs into a slot on the router rear panel. When selected in Cisco IOS software, it is assigned

port gigabitethernet 0/0/0. The default is the built-in RJ-45 1000Base-T connector, which is enabled on this

port.

Only SFP modules certified by Cisco are supported on the routers.

Table 1: SFPs Supported on the Router

DescriptionMinimum

IOS-XE Version

Cisco Model

Number

1000BASE-EX

SFP transceiver

module, SMF,

1310nm, DOM

3.15GLC-EX-SMD

Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router

Installing and Upgrading Internal Modules and FRUs

AC Power Supplies

DescriptionMinimum

IOS-XE Version

Cisco Model

Number

GE SFP, LC

connector

LX/LH

transceiver

3.10GLC-LH-SM

9/1251000Base-ZXGLC-ZX-SM-X=

GE SFP, LC

connector

LX/LH

transceiver; with

DOM

3.10GLC-LH-SMD

GE SFP, LC

connector SX

transceiver

3.10GLC-SX-MM

GE SFP, LC

connector SX

transceiver; with

DOM

3.10GLC-SX-MMD

1000BASE-ZX

SFP

3.10GLC-ZX-SM

1000BASE-ZX

SFP; with DOM

3.16.1GLC-ZX-SMD

100BASE-FX

SFP for FE port

3.10GLC-FE-100FX

100BASE-LX

SFP for FE port

3.10GLC-FE-100LX

100BASE-ZX

SFP (80km)

3.10GLC-FE-100ZX

100BASE-EX

SFP (40km)

3.10GLC-FE-100EX

100BASE-BX10-D

SFP

3.11GLC-FE-100BX-D

100BASE-BX10-U

SFP

3.11GLC-FE-100BX-U

100 V02 SFP on

GE ports

3.10GLC-GE-100

V02

Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router

Installing and Upgrading Internal Modules and FRUs

Installing and Removing SFP Modules

DescriptionMinimum

IOS-XE Version

Cisco Model

Number

1000BASE-BX80

SFP, 1570NM

3.16.1GLC-BX80-D-I

1000BASE-BX80

SFP, 1490NM

3.16.1GLC-BX80-U-I

1000BASE-BX40

SFP, 1550NM

3.16.1GLC-BX40-D-I

1000BASE-BX40

SFP, 1310NM

3.16.1GLC-BX40-U-I

1000BASE-BX

SFP, 1490NM

3.10GLC-BX-D

1000BASE-BX

SFP, 1310NM

3.10GLC-BX-U

1000BASE-SX

SFP transceiver

module for

MMF, 850-nm

wavelength,

extended

operating

temperature

range and DOM

support, dual

LC/PC

connector

3.13SFP-GE-S

CWDM 1470

NM SFP Gigabit

Ethernet and

1G/2G FC

3.10CWDM-SFP-1470

CWDM 1490

NM SFP Gigabit

Ethernet and

1G/2G FC

3.10CWDM-SFP-1490

CWDM 1510

NM SFP Gigabit

Ethernet and

1G/2G FC

3.10CWDM-SFP-1510

CWDM 1530

NM SFP Gigabit

Ethernet and

1G/2G FC

3.10CWDM-SFP-1530

Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router

Installing and Upgrading Internal Modules and FRUs

Installing and Removing SFP Modules

DescriptionMinimum

IOS-XE Version

Cisco Model

Number

CWDM 1550

NM SFP Gigabit

Ethernet and

1G/2G FC

3.10CWDM-SFP-1550

CWDM 1570

NM SFP Gigabit

Ethernet and

1G/2G FC

3.10CWDM-SFP-1570

CWDM 1590

NM SFP Gigabit

Ethernet and

1G/2G FC

3.10CWDM-SFP-1590

CWDM 1610

NM SFP Gigabit

Ethernet and

1G/2G FC

3.10CWDM-SFP-1610

DWDM SFP

1530.33 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-3033

DWDM SFP

1531.12 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-3112

DWDM SFP

1531.90 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-3190

DWDM SFP

1532.68 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-3268

DWDM SFP

1534.25 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-3425

DWDM SFP

1535.04 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-3504

Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router

Installing and Upgrading Internal Modules and FRUs

Installing and Removing SFP Modules

DescriptionMinimum

IOS-XE Version

Cisco Model

Number

DWDM SFP

1535.82 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-3582

DWDM SFP

1536.61 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-3661

DWDM SFP

1538.19 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-3819

DWDM SFP

1538.98 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-3898

DWDM SFP

1539.77 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-3977

DWDM SFP

1540.56 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-4056

DWDM SFP

1542.14 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-4214

DWDM SFP

1542.94 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-4294

DWDM SFP

1543.73 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-4373

DWDM SFP

1544.53 nm SFP

(100 GHz ITU

grid)

3.10DWDM-SFP-4453

Hardware Installation Guide for the Cisco 1100 Series Integrated Services Router

Installing and Upgrading Internal Modules and FRUs

Installing and Removing SFP Modules

Andere Handbücher für 1100 Series

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco 2811 - Voice Security Bundle Router Bedienungsanleitung

Cisco

Cisco NCS 4216 Bedienungsanleitung

Cisco

Cisco Linksys SFE2000 Bedienungsanleitung

Cisco

Cisco DC Power Entry 10005 ESR Bedienungsanleitung

Cisco

Cisco IR1101 Handbuch

Cisco

Cisco 2610XM Kurzanleitung

Cisco

Cisco 800 Series Anleitung zur Verwendung

Cisco

Cisco Profile Series Bedienungsanleitung

Cisco

Cisco 7206VXR - VPN Bundle Router Handbuch

Cisco

Cisco QuickVPN - PC Bedienungsanleitung

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco 2691 - VPN Bundle Router Handbuch

Cisco

Cisco Universal Broadband Router Cisco uBR10012 Handbuch

Cisco

Cisco WRT310N Bedienungsanleitung

Cisco

Cisco 7206 - VXR Router Bedienungsanleitung

Cisco

Cisco ASR1004 - ASR 1004 Modular Expansion Base Bedienungsanleitung

Cisco

Cisco SPS2024 Bedienungsanleitung

Cisco

Cisco ASR 900 Series Anleitung zur Verwendung

Cisco

Cisco 1800 Series Bedienungsanleitung

Cisco

Cisco 1710 Bedienungsanleitung

Cisco

Cisco Unified Communications Manager 8.5(1) Bedienungsanleitung

Cisco

Cisco 4000 Series Bedienungsanleitung

Cisco

Cisco UBR7246VXR Handbuch

Cisco

Cisco RV130 Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung