Cisco 12010 series Bedienungsanleitung
CHAPTER
7-1
Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide
OL-11496-01
7
Maintaining the Router
Your router is equipped as ordered and is ready for installation and startup when
it is shipped. As your networking requirements change, you may need to upgrade
the system by adding or changing components. This chapter describes how to
maintain router components.
Procedures for maintaining the router are described in the following sections:
•Powering Off the Router, page 7-2
•Removing and Installing the Front Covers and Bezel Extenders on Original
Cisco 12010 Series Routers, page 7-3
•Removing and Installing the Front Door on Cisco 12010 Enhanced Series
Router, page 7-11
•Cleaning or Replacing the Chassis Air Filter, page 7-16
•Cleaning or Replacing the Chassis Air Filter, page 7-16
•Removing and Replacing the Blower Module, page 7-23
•Removing and Replacing AC and DC Power Subsystem Components,
page 7-27
•Removing and Replacing Cards from the Chassis, page 7-61
•Upgrading the Switch Fabric in the Cisco 12410 Router, page 7-67
•Removing and Installing a Chassis, page 7-69
Chapter 7 Maintaining the Router
Powering Off the Router
7-2
Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide
OL-11496-01
Prerequisites and Preparation
Before you perform any of the procedures in this chapter, be sure that you:
•Review the “Safety Guidelines” section on page 2-2.
•Read the safety and ESD-prevention guidelines described in the “Compliance
and Safety Information” section on page 2-3.
•Ensure that you have all of the necessary tools and equipment before
beginning the procedure.
•Have access to the following documents during the installation:
–
Regulatory Compliance and Safety Information for Cisco 12000 Series
Routers publication that shipped with the router (PN 78-4347-xx)
Powering Off the Router
Most Cisco 12010, Cisco 12410, and Cisco 12810 series routers field-replaceable
units (FRUs) can be removed and replaced with the power on and the system
operating. This is known as online insertion and removal (OIR). Power supplies,
line cards, the RP, CSCs, SFCs, and alarm cards all support OIR. Unless otherwise
noted, the maintenance tasks described in this chapter can be performed while the
router remains powered on.
In some cases it may be necessary to power off the router, for example, to upgrade
both power supplies and PDUs. Use the following procedure to power off the
router.
Step 1 Set the power switch on each power supply to the off (0) position.
Step 2 Power off all circuit breakers for the source power lines connected to the power
supplies.
Step 3 Verify that the Pwr OK indicator on each power supply is off.
Step 4 Verify that the OK indicator on the blower module is off.
7-3
Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide
OL-11496-01
Chapter 7 Maintaining the Router
Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers
Removing and Installing the Front Covers and Bezel
Extenders on Original Cisco 12010 Series Routers
The front covers are fastened to the chassis by ball studs that insert into clips on
the front of the chassis. The front covers are referred to as snap-on front covers.
The partial front cover on the air filter door is fastened to the air filter door by four
screws inserted from the back side of the air filter door. This partial front cover is
referred to as the air filter door front cover.
Note Recently released routers have bezel extenders installed on the front cover (bezel)
for the line card and route processor (RP) card cage to bring the cover out an
additional 2 inches (50.8 mm) to allow more room for cables. If your chassis does
not have these extenders and you want to purchase them, contact Cisco sales. (See
the “Attaching Bezel Extenders to the Front Cover” section on page 7-6 if you are
installing the bezel extenders.)
Removing the Front Covers
The front covers are held in place by ball studs that snap into clips on the chassis.
Refer to Figure 7-1 and use the following procedure to remove the snap-on front
covers.
Step 1 Grasp the outside edges of the blower module front cover and pull it straight out
to detach the front cover from the chassis.
Step 2 Repeat Step 1 for the RP and line card cage front cover.
Chapter 7 Maintaining the Router
Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers
7-4
Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide
OL-11496-01
Installing the Front Covers
Refer to Figure 7-1 and use the following procedure to install the front covers.
Step 1 Hold the front cover by its outside edges and align the ball studs with the ball stud
clips on the front of the chassis.
Step 2 Push the front cover into the ball stud clips and the front cover is flush with the
front of the chassis.
Step 3 Repeat Step 1 and Step 2 for the remaining front cover.
7-5
Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide
OL-11496-01
Chapter 7 Maintaining the Router
Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers
Figure 7-1 Removing and Installing the Front Covers
Chapter 7 Maintaining the Router
Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers
7-6
Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide
OL-11496-01
Attaching Bezel Extenders to the Front Cover
Use the following procedure to attach the bezel extenders to the card cage front
cover.
Step 1 Remove the line card and RP card cage front cover from the chassis as described
in the “Removing the Front Covers” section on page 7-3.
Step 2 Remove the four ball studs from the front cover (Figure 7-2, item 3).
Step 3 Screw the four ball studs into the threaded holes on the bezel extenders (two ball
studs for each bezel extender) using a wrench to secure them.
Caution Do not overtighten the ball studs. Overtightening the ball studs could damage the
threaded hole on the bezel extender.
Step 4 Attach the bezel extenders to the front cover:
a. Facing the inside of the front cover, align the screw holes in the left side bezel
extender with the mounting screw holes in the front cover (Figure 7-2,
item 4).
Note If you cannot align both screw holes on the front cover inserts, you have
the incorrect bezel extender. Try the other bezel extender on this side.
b. Fasten the bezel extender to the front cover with the mounting screws
(Figure 7-2, item 2).
Caution Do not overtighten the screws. Overtightening the screws could damage the
threaded holes in the front cover.
c. Repeat Steps aand bto fasten the right side bezel extender to the other side
of the front cover (Figure 7-2, item 5).
7-7
Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide
OL-11496-01
Chapter 7 Maintaining the Router
Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers
Figure 7-2 Attaching the Bezel Extenders to the Front Cover
1Line card and RP card cage front cover (bezel) 4Left side bezel extender
2Mounting screws 5Right side bezel extender
3Ball studs ––
Chapter 7 Maintaining the Router
Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers
7-8
Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide
OL-11496-01
Step 5 Hold the front cover by its outside edges and align the ball studs with the ball stud
clips on the front of the chassis (Figure 7-3).
Figure 7-3 Attaching the Front Cover Using Bezel Extenders
Step 6 Push the front cover into the ball stud clips so that the front cover is flush with the
front of the chassis.
7-9
Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide
OL-11496-01
Chapter 7 Maintaining the Router
Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers
Removing and Replacing the Air Filter Door Front Cover
Use the following procedure to remove and replace the air filter door front cover.
Step 1 Loosen the captive screws on each side of the air filter door and swing the door
away from the switch fabric and alarm card cage.
Figure 7-4 Opening the Air Filter Door
Caution Be especially careful not to damage the honeycomb screen on the back of the air
filter door and on the inside of the switch fabric and alarm card cage. Damaging
the honeycomb screen can restrict the air flow and cause overheating and diminish
EMI protection.
Chapter 7 Maintaining the Router
Removing and Installing the Front Covers and Bezel Extenders on Original Cisco 12010 Series Routers
7-10
Cisco 12010, Cisco 12410, and Cisco 12810 Router Installation and Configuration Guide
OL-11496-01
Step 2 Remove the (4) screws from each corner that fasten the partial front cover to the
air filter door (Figure 7-5).
•Set aside the screws; you will need them to install the replacement front
cover.
Figure 7-5 Removing the Air Filter Door Front Cover
Step 3 Hold the replacement front cover by its outside edges and align the screw holes in
the front cover with the holes on the air filter door.
Step 4 Secure the front cover to the air filter door using the (4) screws that you removed
in Step 2.
Caution Do not overtighten the screws. Overtightening the screws can damage the
threaded holes in the air filter door.
Step 5 Close the air filter door and tighten the captive screws.
Caution Align and seat the door carefully to avoid damaging the EMI-preventive gaskets
on the door. The air filter door must be closed and secured at all times to maintain
correct EMI performance.
Andere Handbücher für 12010 series
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Cisco Netzwerk-Router Handbücher
Cisco
Cisco 6000 series Technisches Handbuch
Cisco
Cisco Linksys WRT54G3GV2-ST Bedienungsanleitung
Cisco
Cisco 1417 Bedienungsanleitung
Cisco
Cisco ON100 Network Agent Bedienungsanleitung
Cisco
Cisco 800 Series Handbuch
Cisco
Cisco ASR 5000 Bedienungs- und Wartungshandbuch
Cisco
Cisco Router Cisco 831 Anleitung zur Verwendung
Cisco
Cisco WRP500 Bedienungsanleitung
Cisco
Cisco 860 Series Handbuch
Cisco
Cisco ASR-920-8S4Z-PD Handbuch
Cisco
Cisco 7200 VXR Series Bedienungsanleitung
Cisco
Cisco CISCO1750 Bedienungsanleitung
Cisco
Cisco 5915 Kurzanleitung
Cisco
Cisco CISCO7206 Originalbetriebsanleitung
Cisco
Cisco ASR 9000 Series Bedienungsanleitung
Cisco
Cisco 1750 Handbuch
Cisco
Cisco uBR10012 Universal Broadband Router... Bedienungsanleitung
Cisco
Cisco Router Cisco 7206 VXR Bedienungsanleitung
Cisco
Cisco CRS Series Bedienungsanleitung
Cisco
Cisco Cisco 12416 Bedienerhandbuch
