Cisco 1603R Bedienungsanleitung
Quick Start Guide
INSTALLING YOUR
CISCO 1600 SERIES ROUTER
UNPACK THE BOX
INSTALL THE ROUTER
VERIFY YOUR INSTALLATION
Cisco 1600
Hub
PC
PC
PC
PC
PC
Internet
Ethernet
network
WAN
connection Backup
WAN connection
(optional)
PC
Server
Server
1
2
3
2
Note: For Items That You Provide—You need only the items required to install your specific Cisco 1600 model.
Cables ordered from Cisco are colored as shown below.
Unpack the Box.
Note: The Cisco 1600 series routers are either of run-from-flash (RFF) or run-from-RAM (RFR) models. In
this document, model names without an R refer to both models. The “Router Memory” section in the hardware
installation guide that came with your router describes the differences between RFF and RFR models.
Cisco 1600 Router
Accessory Kit Items
Power supply
Power cord (black)
Software
Configuration
Product documentation
Items That You Provide
10BaseT Ethernet cable
RJ-48S-to-RJ-48S (Cisco 1602)
(blue, if ordered from Cisco)
RJ-45-to-RJ-45
(red if ordered from Cisco for Cisco 1603)
(orange if ordered from Cisco for Cisco 1604)
Ethernet AUI cable
Hardware
Installation
Documentation
CD
Ethernet AUI transceiver or Ethernet 10BaseT hub
WAN interface card
(optional, might already be installed)
Phillips screwdriver
(if installing a WAN interface card)
Serial cable (Cisco 1601)
(blue if ordered from Cisco)
DB-25-to-DB-9 console
adapter (light gray)
Console cable
(light blue, RJ-45-to-DB-9)
3
There are four steps to installing your router:
Install the Router.
Warning Hazardous network voltages are present in WAN interface card ports regardless of whether
power to the router is OFF or ON. To avoid electric shock, use caution when working near WAN ports.
When detaching cables, detach the end away from the router first.
A. Connect the router to your Ethernet network.
B. Install a WAN interface card in the router (optional). If the card is not already installed, and you want to
use a card with the router, you must install it.
C. Connect the router to the WAN line. This is the telephone line (Frame Relay, serial, 56-kbps, or ISDN) that
is supplied by the telephone company.
D. Connect the router to the power supply. After you connect the power, you can confirm proper installation
by checking that certain LEDs are on.
Note: If you’re not sure what Cisco 1600 router model you are using, look on the rear panel.
DONOTINSTALLANYWAN
MODULEWITHPOWERON
Cisco 1601
4
A. Connect the router to the local network.
Install the Router (continued).
Connect the router to your local Ethernet network in
one of three ways:
Option 1: Connect the ETHERNET Ø 10BASET
port to an Ethernet hub or switch.
Option 2: Connect the ETHERNET Ø AUI port to
an Ethernet transceiver.
Option 3: Connect the ETHERNET Ø 10BASET
port to your PC.
Option 1
You must provide the Ethernet hub or switch and the
RJ-45-to-RJ-45 cable required for this connection.
Connect one end of the cable to the yellow
ETHERNET Ø 10BASET port.and the other end to
a network port on the 10BaseT hub or switch.
Option 2
You must provide the transceiver and AUI cable for
this connection. If the transceiver that you are using
connects directly to the router, you do not need the
cable.
DONOTINSTALLANYWAN
MODULEWITHPOWERON
LNK LED
Connect one end of the Ethernet transceiver to the
yellow ETHERNET Ø AUI port and the other end
to the Ethernet network.
Option 3
You must provide an Ethernet crossover cable for
this connection.
Connect one end of the crossover cable to the yellow
ETHERNET Ø 10BASET port and the other end to
the Ethernet connector on the back of your
computer.
DONOTINSTALLANYWAN
MODULEWITHPOWERON
DONOTINSTALLANYWAN
MODULEWITHPOWERON
5
B. Install the WAN interface card.
Look for a WAN interface card in the slot on the right-rear of the router, just above the slot labeled FLASH PC
CARD. (There is no WAN interface card installed if there is a metal plate over the slot.) If the card is already
installed, connect the card to your WAN line according to the instructions that came with the card. To install a
card, follow the instructions below.
Install the Router (continued).
Note: You must provide a Phillips
screwdriver for this step.
Step 1 Turn the power OFF by putting
the power switch in the O position.
Step 2 Remove the thumbscrews that
hold the slot cover in place.
Step 3 Remove the metal plate that
covers the card slot.
Step 4 Hold the card by the edges and
line it up with the guide on the card slot.
Step 5 Insert the card into the slot and
push in until it is firmly seated in the
connector and the card front panel is flush
with the router rear panel.
Step 6 Use the Phillips screwdriver to
tighten the screws that are in the card.
Step 7 Connect the correct cable to the
card according the instructions that came
with the card.
Step 8 Turn the power ON by putting
the power switch in the | position.
DONOTINSTALLANYWAN
MODULEWITHPOWERON
6
(
C. Connect the router to the wide-area network.
Install the Router (continued).
Each of the Cisco 1600 routers supports a different type of wide-area network (WAN) connection. This section
describes how to make these connections. The model number of your router is on the rear panel.
• Cisco 1601—This page
• Cisco 1602—Page 7
• Cisco 1603—Page 8
• Cisco 1604—Page 9
Cisco 1601 Serial Connection
Note: For this step, you must order a standard serial cable from Cisco. When you order the cable, specify the
type of serial line you are using.
Step 1 Connect one end of the serial cable to the blue SERIAL Ø port on the rear panel.
Step 2 Depending on what is required by your telephone company, do one of the following:
• Connect the other end of the cable to an external device such as an asynchronous modem, a
synchronous modem, or other DCE equipment (as shown in this illustration).
• Connect the other end of the cable directly to the wall jack.
DONOTINSTALLANYWAN
MODULEWITHPOWERON
RDY LED
External DCE equipment
7
C. Connect the router to the wide-area network (continued).
Cisco 1602 56-Kbps Connection
Note: You must provide an RJ-45-to-RJ-45 cable for this step.
Step 1 Connect one end of the cable to the blue SERIAL Ø 56K DSU/CSU port on the rear panel.
Step 2 Connect the other end of the cable to the 56-Kbps wall jack.
56-Kbps wall jack
CARRIER LED
8
C. Connect the router to the wide-area network (continued).
Cisco 1603 ISDN BRI S/T Connection
Note: You must provide a straight-through RJ-45-to-RJ-45 cable and (if required for your site) a network
termination (NT1) device for this connection.
Step 1 Connect one end of the cable to the orange ISDN BRI Ø S/T port on the rear panel.
Step 2 Depending on what is required by your telephone company, do one of the following:
• Connect the other end of the cable to an external NT1, then connect the NT1 to the ISDN wall jack.
• Connect the other end of the cable to the ISDN wall jack (as shown in this illustration).
OK LED
9
C. Connect the router to the wide-area network (continued).
Cisco 1604 ISDN BRI U Connection
Note: You must provide a straight-through cable, either RJ-11-to-RJ-11 (standard telephone cable) or
RJ-45-to-RJ-45, for this connection.
Step 1 Connect one end of the cable to the red ISDN BRI Ø port on the rear panel.
Step 2 Connect the other end directly to the ISDN wall jack.
For instructions on connecting another ISDN device such as a fax or telephone to the ISDN PHONE port, refer
to the hardware installation guide that came with your router.
NT1 LED
10
D. Connect the power supply.
Install the Router (continued).
After connecting the router to power and turning it on, you can confirm that you have installed the router
correctly by checking certain LEDs. Connect the router to the power supply as shown below. Depending on
where you install the router, your power supply and power outlet could be different from those in the picture.
Step 1 Connect the power supply cord to the power socket on the rear panel.
Step 2 Connect the power supply to a power outlet.
Confirm that the router has power by checking that the SYSTEM PWR LED on the front panel is on.
Step 3 Confirm that the router has power by checking that the SYSTEM PWR LED on the front panel is on.
DONOTINSTALLANYWAN
MODULEWITHPOWERON
Andere Handbücher für 1603R
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Cisco Netzwerk-Router Handbücher
Cisco
Cisco Aironet 350 Series Bedienungsanleitung
Cisco
Cisco Small Business Pro SRP527W Bedienungsanleitung
Cisco
Cisco NCS 5500 Series Bedienungsanleitung
Cisco
Cisco Catalyst 2960 Series Bedienungsanleitung
Cisco
Cisco Linksys WRK54G Bedienungsanleitung
Cisco
Cisco 7513 Series Bedienungsanleitung
Cisco
Cisco Network Convergence System 6000 Series Bedienungsanleitung
Cisco
Cisco 880 Series Bedienungsanleitung
Cisco
Cisco 3700 series Bedienungsanleitung
Cisco
Cisco ASR 903 Bedienungsanleitung
Cisco
Cisco 805 Series Bedienungsanleitung
Cisco
Cisco Profile Series Bedienungsanleitung
Cisco
Cisco DC Power Entry 10005 ESR Bedienungsanleitung
Cisco
Cisco ASR 901S Series Merkblatt
Cisco
Cisco NCS 4216 Bedienungsanleitung
Cisco
Cisco RV042 - Small Business Dual WAN VPN Router Bedienungsanleitung
Cisco
Cisco ASR 9000 Series Merkblatt
Cisco
Cisco WTR54GS Bedienungsanleitung
Cisco
Cisco 7609 Bedienungsanleitung
Cisco
Cisco Small Business RV315W Bedienungsanleitung
