Cisco 2524 - Router - EN Bedienungsanleitung

CHAPTER

Configuring the Cisco 2524 and Cisco 2525 Routers 4-1

Configuring the Cisco 2524 and

Cisco 2525 Routers

This chapter describes how to configure the Cisco 2524 and Cisco 2525 routers and

contains the following sections:

•Booting the Router for the First Time

•Configuring the Router

•Specifying the Boot Method

•Checking the Configuration Settings

•Getting More Information

This chapter provides just enough information to get the router up and running. For

Cisco IOS Release 11.0 and earlier releases, refer to the Router Products Configuration

Guide for additional configuration information. For Cisco IOS Release 11.1 and later

releases, refer to the Configuration Fundamentals Configuration Guide.

Booting the Router for the First Time

Each time you power on the router, it goes through the following boot sequence:

1The router goes through power-on self-test diagnostics to verify basic operation of the

CPU, memory, and interfaces.

2The system bootstrap software (boot image) executes and searches for a valid Cisco IOS

image (router operating system software). The source of the Cisco IOS image (Flash

memory or a Trivial File Transfer Protocol [TFTP] server) is determined by the

configuration register setting. The factory-default setting for the configuration register

is 0x2102, which indicates that the router should attempt to load a Cisco IOS image

from Flash memory.

4-2 Cisco 2524 and Cisco 2525 Router User Guide

Configuring the Router

3If after five attempts a valid Cisco IOS image is not found in Flash memory, the router

reverts to boot ROM mode (which is used to install or upgrade a Cisco IOS image).

4If a valid Cisco IOS image is found, then the router searches for a valid configuration

file.

5If a valid configuration file is not found in NVRAM, the router runs the System

Configuration Dialog so you can configure it manually. For normal router operation,

there must be a valid Cisco IOS image in Flash memory and a configuration file in

NVRAM.

The first time you boot your router, you will need to configure the router interfaces and then

save the configuration to a file in NVRAM. Proceed to the next section, “Configuring the

Router,” for configuration instructions.

Configuring the Router

You can configure the router using one of the following procedures:

•Configuration mode—Recommended if you are familiar with Cisco IOS commands.

•AutoInstall—Recommended for automatic installation if another router running

Cisco IOS software is installed on the network. This configuration method must be set

up by someone with experience using Cisco IOS software.

•System Configuration Dialog—Recommended if you are not familiar with Cisco IOS

commands.

Use the procedure that best fits the needs of your network configuration and level of

Cisco IOS experience.

Timesaver Acquire the correct network addresses from your system administrator or

consult your network plan to determine correct addresses before you begin to configure the

router.

Configuring the Cisco 2524 and Cisco 2525 Routers 4-3

Configuring the Router

Using Configuration Mode

You can configure the router manually if you prefer not to use AutoInstall or the System

Configuration Dialog. Take the following steps to configure the router manually:

Step 1 Connect a console terminal following the instructions in the section “Connecting

the Console Terminal and Modem” in the chapter “Installing the Cisco 2524 and

Cisco 2525 Routers,” and then power ON the router.

Step 2 When you are prompted to enter the initial dialog, enter no to go into the normal

operating mode of the router:

Would you like to enter the initial dialog? [yes]: no

Step 3 After a few seconds you will see the user EXEC prompt (Router>). Enter the

enable command to enter enable mode. You can only make configuration changes

in enable mode.

Router> enable

The prompt changes to the privileged EXEC (enable) prompt:

Router#

Step 4 Enter the configure terminal command at the enable prompt to enter

configuration mode:

Router# configure terminal

You can now enter any changes you want to the configuration.

Step 5 Press Ctrl-Z to exit configuration mode.

To see the current operating configuration, enter the show running-config command at the

enable prompt:

Router# show running-config

To see the configuration in NVRAM, enter the show startup-config command at the enable

prompt:

Router# show startup-config

4-4 Cisco 2524 and Cisco 2525 Router User Guide

Configuring the Router

The results of the show running-config and show startup-config commands will be

different if you have made changes to the configuration but have not yet written them to

NVRAM.

To make your changes permanent, enter the copy running-config startup-config

command at the enable prompt:

Router# copy running-config startup-config

********

The router is now configured and will boot with the configuration you entered.

Using AutoInstall

The AutoInstall process is designed to configure the router automatically after connection

to your WAN. In order for AutoInstall to work properly, a Transmission Control

Protocol/Internet Protocol (TCP/IP) host on your network must be preconfigured to provide

the required configuration files. The TCP/IP host may exist anywhere on the network as

long as the following two conditions are maintained:

1The host must be on the remote side of the router’s synchronous serial connection to the

WA N .

2User Datagram Protocol (UDP) broadcasts to and from the router and the TCP/IP host

must be enabled.

This functionality is coordinated by your system administrator at the site where the TCP/IP

host is located. You should not attempt to use AutoInstall unless the required files have been

provided on the TCP/IP host. For Cisco IOS Release 11.0 and earlier releases, refer to the

publication Router Products Configuration Guide for additional information. For

Cisco IOS Release 11.1 and later releases, refer to the publication Configuration

Fundamentals Configuration Guide.

Note AutoInstall works on synchronous serial connections only. The 2-wire

switched 56-kbps DSU/CSU module operates on switched 56-kbps circuits only; therefore,

you cannot use it for AutoInstall.

Configuring the Cisco 2524 and Cisco 2525 Routers 4-5

Configuring the Router

Take the following steps to prepare your router for the AutoInstall process:

Step 1 Attach the WAN cable to the router.

Step 2 Turn ON power to the router.

The router will load the operating system image from Flash memory. If the remote

end of the WAN connection is connected and properly configured, the AutoInstall

process will begin.

If AutoInstall successfully completes, you can write the configuration data to the

router’s NVRAM. Perform the following step to complete this task.

Step 3 Enter the copy running-config startup-config command:

Router# copy running-config startup-config

Taking this step saves the configuration settings that the AutoInstall process

created in the router. If you do not do this, your configuration will be lost the next

time you reload the router.

Using the System Configuration Dialog

If you do not plan to use AutoInstall, make sure all the WAN cables are disconnected from

the router. This will prevent the router from attempting to the run the AutoInstall process.

The router will attempt to run AutoInstall whenever you power it on if there is a WAN

connection on both ends and the router does not have a configuration file stored in

NVRAM. It can take several minutes for the router to determine that AutoInstall is not set

up to a remote TCP/IP host.

If your router does not have a configuration (setup) file and you are not using AutoInstall,

the router will automatically start the setup command facility. An interactive dialog called

the System Configuration Dialog appears on the console screen. This dialog helps you

navigate through the configuration process by prompting you for the configuration

information necessary for the router to operate.

Many prompts in the System Configuration Dialog include default answers, which are

included in square brackets following the question. To accept a default answer, press

Return; otherwise, enter your response.

This section gives an example configuration using the System Configuration Dialog. When

you are configuring your router, respond as appropriate for your network.

4-6 Cisco 2524 and Cisco 2525 Router User Guide

Configuring the Router

At any time during the System Configuration Dialog, you can request help by typing a

question mark (?) at a prompt.

Before proceeding with the System Configuration Dialog, obtain from your system

administrator the node addresses and the number of bits in the subnet field (if applicable)

of the Ethernet and synchronous serial ports. For more information about Internet Protocol

(IP) addresses and subnets, refer to the publication Internetworking Technology Overview.

(See the section “Getting More Information” at the end of this chapter.)

Take the following steps to configure the router using the System Configuration Dialog:

Step 1 Connect a console terminal to the console connector on the rear panel of your

router, and turn ON power to the router. (For more information, refer to the section

“Connecting the Console Terminal and Modem” in the chapter “Installing the

Cisco 2524 and Cisco 2525 Routers.”)

Note The default parameters for the console port are 9600 baud, 8 data bits, no parity, and

2 stop bits.

Step 2 After about 30 seconds, information similar to the following is displayed on the

console screen.

Note The messages displayed vary, depending on the Cisco IOS release and feature set

you selected. The screen displays in this section are for reference only and may not exactly

reflect the screen displays on your console.

When you see this information, you have successfully booted your router:

System Bootstrap, Version X.X(XXXX) [XXXXX XX], RELEASE SOFTWARE

2500 processor with 4096 Kbytes of main memory

Notice: NVRAM invalid, possibly due to write erase.

F3: 5797928+162396+258800 at 0x3000060

Configuring the Cisco 2524 and Cisco 2525 Routers 4-7

Configuring the Router

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

Rights clause at FAR sec. 52.227-19 and subparagraph

Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) X000 Software (IGS-J-L), Version XX.X(XXXX) [XXXXX XXX]

Compiled Fri 20-Oct-95 16:02 by XXXXX

Image text-base: 0x03030FC0, data-base: 0x00001000

Cisco 252X (68030) processor (revision A) with 4092K/2048K bytes of

memory.

Processor board ID 00000000

Bridging software.

X.25 software, Version X.X, NET2, BFE and GOSIP compliant.

Basic Rate ISDN software, Version X.X.

1 Ethernet/IEEE 802.3 interface.

2 Serial network interfaces.

1 ISDN Basic Rate interface.

32K bytes of non-volatile configuration memory.

8192K bytes of processor board System flash (Read ONLY)

Notice: NVRAM invalid, possibly due to write erase.

--- System Configuration Dialog ---

At any point you may enter a question mark '?' for help.

Refer to the 'Getting Started' Guide for additional help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Would you like to enter the initial configuration dialog? [yes]:

Step 3 Press Return or enter yes to begin the configuration process.

4-8 Cisco 2524 and Cisco 2525 Router User Guide

Configuring the Router

Step 4 When the System Configuration Dialog asks whether you want to view the current

interface summary, press Return or enter yes:

First, would you like to see the current interface summary? [yes]:

Any interface listed with OK? value "NO" does not have a valid

configuration

Interface IP-Address OK? Method Status Protocol

Ethernet0 unassigned NO not set up down

BRI0 unassigned NO not set up up

Serial0 unassigned NO not set down down

Serial1 unassigned NO not set down down

Step 5 Configure the global parameters. Choose which protocols to support on the

Ethernet interface. For IP installations, you can press Return to accept the default

values (in brackets) for most of the questions. A typical configuration follows:

Configuring global parameters:

Enter host name [Router]:

Next, you are prompted to enter an enable secret password. There are two types of

privileged-level passwords:

•Enable secret password (a very secure, encrypted password)

•Enable password (a less secure, nonencrypted password)

The enable password is used when the enable secret password does not exist.

For maximum security, be sure the passwords are different. If you enter the same

password for both, the router will accept your entry, but will display a warning

message indicating that you should enter a different password.

Step 6 Enter an enable secret password:

The enable secret is a one-way cryptographic secret used

instead of the enable password when it exists.

Enter enable secret: pail

The enable password is used when there is no enable secret

and when using older software and some boot images.

Configuring the Cisco 2524 and Cisco 2525 Routers 4-9

Configuring the Router

Step 7 Enter the enable and virtual terminal passwords:

Enter enable password: shovel

Enter virtual terminal password: vterm1

Step 8 Press Return to accept Simple Network Management Protocol (SNMP)

management, or enter no to refuse it:

Configure SNMP Network Management? [yes]: no

Step 9 In the following example, the router is configured for AppleTalk, IP, and IPX.

Configure the appropriate protocols for your router:

Configure Vines? [no]:

Configure LAT? [no]:

Configure AppleTalk? [no]: yes

Multizone networks? [no]: yes

Configure DECnet? [no]:

Configure IP? [yes]:

Configure IGRP routing? [yes]:

Your IGRP autonomous system number [1]: 15

Configure CLNS? [no]:

Configure bridging? [no]:

Configure IPX? [no]: yes

Configure XNS? [no]:

Configure Apollo? [no]:

Step 10 Enter the ISDN BRI switch type for the router. The ISDN switch type appropriate

for the router depends on the ISDN provider’s equipment. Table 4-1 lists the ISDN

switch types.

Enter ISDN BRI Switch Type [none]: basic-5ess

4-10 Cisco 2524 and Cisco 2525 Router User Guide

Configuring the Router

Table 4-1 ISDN Switch Types

Configuring the ISDN BRI Interface

This section explains how to configure the ISDN BRI interface. If an ISDN BRI WAN

module is not installed in your router, skip this section and proceed with the next section,

“Configuring the Ethernet or Token Ring Interfaces.”

Country ISDN Switch Type Description

Australia basic-ts013 Australian TS013 switches

Europe basic-1tr6 German 1TR6 ISDN switches

basic-nwnet3 Norwegian NET3 ISDN switches (phase 1)

basic-net3 NET3 ISDN switches (UK and others)

vn2 French VN2 ISDN switches

vn3 French VN3 ISDN switches

Japan ntt Japanese NTT ISDN switches

North America basic-5ess AT&T basic rate switches

basic-dms100 NT DMS-100 basic rate switches

basic-ni1 National ISDN-1 switches

New Zealand basic-nznet3 New Zealand NET3 switches

Andere Handbücher für 2524 - Router - EN

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Cisco Netzwerk-Router Handbücher

Cisco

Cisco 4451-X Handbuch

Cisco

Cisco uBR10012 Universal Broadband Router... Bedienungsanleitung

Cisco

Cisco ASR 1002-F Installationsanleitung

Cisco

Cisco 10000 Series Bedienungsanleitung

Cisco

Cisco Linksys SFE2000 Anleitung zur Verwendung

Cisco

Cisco NCS 5500 Series Handbuch

Cisco

Cisco 3825 Series Service-Handbuch

Cisco

Cisco RV132W Bedienungsanleitung

Cisco

Cisco RV082 - Small Business VPN Router Bedienungsanleitung

Cisco

Cisco 4000 Series Bedienungsanleitung

Cisco

Cisco WTR54GS Bedienungsanleitung

Cisco

Cisco RV260 series Bedienungsanleitung

Cisco

Cisco C3230-1W-49-K9 - 3230 WMIC Card Bundle... Anwendungshandbuch

Cisco

Cisco GSR12/60 - 12012 Router -AnyLAN Bedienerhandbuch

Cisco

Cisco 12000 - Series Chassis Modular Expansion... Kurzanleitung

Cisco

Cisco 2600 Series Handbuch

Cisco

Cisco 12406 series Bedienungsanleitung

Cisco

Cisco NCS 540 Bedienungsanleitung

Cisco

Cisco 3845 - Security Bundle Router Bedienungsanleitung

Cisco

Cisco uBR924 Bedienungsanleitung

Cisco

Cisco 7401ASR Bedienerhandbuch

Cisco

Cisco ASR 9000 Series Bedienungsanleitung

Cisco

Cisco SB 100 Series Originalbetriebsanleitung

Cisco

Cisco 860 Series Handbuch

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

LevelOne

LevelOne FBR-1416 Bedienungsanleitung

Dynacord

Dynacord Promatrix 6000 Bedienungsanleitung

Lorex

Lorex F5D8230-4 Bedienungsanleitung